At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
To replace the brake lamp of Your volkswagen beetle 2001 model is relatively simple. Please follow the steps below:
To remove the lens and gain access to the bulbs You first need to release the lens holder from inside the trunk by completely unscrewing the large plastic wing nut that is under a round plastic panel that's located almost directly behind the rear brake light lens.
To gain access to the plastic wing nut remove the round panel by gently prying it off.
After this is done You release the lens by using something flat like a dinner table knife to pry and release the clip that holds the lens in place.
Locating the clip: The rear fender has two seams that end at the light lens, the inboard seam (the one closest to the hatch)is where you want to insert the table knife to pry the metal clip that holds the lens in place.
Gently and carefully insert the knife blade directly at the seam and pry upward to release the lens.
Once the clip releases pull the lens the rest of the way and remove the bulbs by turning the bulb holder sockets counter-clockwise.
After this is done remove bulbs by slightly pushing down on the bulb and turning it counter-clockwise.
The reinstall is reverse of the removal the procedure.
When re-installing take care to clock the lens where the metal clip and the lens protrusions end up in the same position as before.
You may need to assist sliding the lens retaining clip in with the knife when reinstalling.
The process for changing the tail light bulbs for a 2003 New Beetle TDI is relatively simple.
To remove the lens and gain access
to the bulbs you first need to release the lens holder from inside the
trunk by completely unscrewing the large plastic wing nut that is under
a round plastic panel that's located almost directly behind the rear
brake light lens.
To gain access to the plastic wing nut remove the
round panel by gently prying it off. After this is done you release the lens by using something flat like screwdriver to pry and
release the clip that holds the lens in place. Locating the clip: The
rear fender has two seams that end at the light lens, the inboard seam
(the one closest to the hatch)is where you want to insert the table
knife to pry the metal clip that holds the lens in place.
Gently and
carefully insert the flathead screwdriver directly at the seam and pry upward to
release the lens. Once the clip releases pull the lens the rest of the
way and remove the bulbs by turning the bulb holder sockets counter-clockwise. After this is done remove bulbs by slightly pushing
down on the bulb and turning it counter-clockwise.
To reinstall is
reverse of the removal the procedure. When re-installing take care to
clock the lens where the metal clip and the lens protrusions end up
in the same position as before. Note: you may need to assist sliding
the lens retaining clip in with the screwdriver when reinstalling!
jack up truck support it remove tire you should see the caliper,on the back side you will see two small bolts lossen the bolts remove it might require some prying support the caliper,check the rotor if has grooves in it it should be turned. use a c clamp to force the piston back in the caliper be careful of the rubber seal put the new pads on reinstall the caliper tighten the bolts start the truck pump the brakes a few times go back check for leaks if none put tire back on remove support lower to ground test drive
Try the wireing harness on the driver side rear to the passenger side you may have some wires caroded also it could be shorted out pig tails. If this helped you please rate this free question and if you need more help post here and thanks for using for Fix-ya.com
I don't know this van but many tail light assembly's have a couple of screws you remove then a couple of snap clips. So after you remove the screws you gently pry the assembly off with a slim pry tool.
Yes, there is a "spear point" plastic clip that is still engaged into a socket type holder in the front outboard portion of the tail lamp assembly. Pry gently with a tape wrapped screwdriver at the front outboard corner of the assembly and the clip will release. You will then be able to see how the clip works and will be able to align and engage it first when replacing the tail lamp assembly.
jack & support vehicle. remove rear axle cover drain fluid, removeleft rear tire drum/rotor brakes, remove bolt in axle housing that holds the 3/4 inch pin in place pull pin , push left axle shaft inwards and remove c clip from inside axle case,slide out axle shaft,remove seal,remove bearing and install in revers
The process for changing the tail light bulbs for a 2002 New Beetle in my case a TDI is relatively simple. To remove the lense and gain access to the bulbs you first need to release the lense holder from inside the trunk by completely unscrewing the large plastic wing nut that is under a round plastic panel that's located almost directly behind the rear brake light lense. To gain access to the plastic wing nut remove the round panel by gently prying it off. After this is done you release the lense by using something flat like a dinner table knife to pry and release the clip that holds the lense in place. Locating the clip: The rear fender has two seams that end at the light lense, the inboard seam (the one closest to the hatch)is where you want to insert the table knife to pry the metal clip that holds the lens in place. Gently and carefully insert the knife blade directly at the seam and pry upward to release the lense. Once the clip releases pull the lens the rest of the way and remove the bulbs by turning the bulb holder sockets couter-clockwise. After this is done remove bulbs by slightly pushing down on the bulb and turning it counter-clockwise. The reinstall is reverse of the removal the procedure.When re-installing take care to clock the lense where the metal clip and the lense protrusions end up in the same position as before. Note: you may need to assist sliding the lens retaining clip in with the knife when reinstalling! Good luck
×