2007 Toyota FJ Cruiser Logo
Posted on Aug 16, 2008

Shaking with engine light and VSC Off lights turned on

My 2007 FJ Cruiser is shaking while in park and the engine lights have turned on along with all other light below it. What do you think has caused this? How can I fix it?

  • 2 more comments 
  • martinezhect Sep 02, 2008

    I HAVE THE SAME PROBLEM J. CABALLERO AND I DON'T KNOW WHAT TO DO? PLEASE HELP ME WITH THIS PROBLEM ALL THE LIGTH ARE TURN ON! LIKE ENGINE,TRACCTION CONTROL,VSC OFF AND VSC TRAC.

    THANKS

  • ecore01 Dec 06, 2008

    I have the same problem too with the lights, no shaking engine.
    Does any-one found the solution?
    The fuses seem to be OK, can't find any reason why all lights (all lights up are: Check Engine Indicator, Slip Indicator, VSC trac, VSC off) light up.

    First check all fuses (see your manual and write down all fuse-numbers that are dealing with Vehicle Stability), some fuses are both VSC and Fuel Injection. That could cause all lights and shaking engine.

  • Anonymous Mar 21, 2009

    This morning I experience a similar issue. All 4 indicators stay lit.
    They were the CHECK ENGINE...SLIP INDICATOR..VSC TRAC..VSC OFF.

    I take it from the other postings there is a bug that the dealer should be aware of...BTW, I'm @ 55K miles...

  • Anonymous Mar 25, 2014

    I have a 2007 FJ cruiser. It has a factory subwoofer installed. How do you remove the subwoofer to change the light?

×

1 Answer

ecore01

Level 1:

An expert who has achieved level 1.

  • Contributor 1 Answer
  • Posted on Dec 06, 2008
ecore01
Contributor
Level 1:

An expert who has achieved level 1.

Joined: Dec 06, 2008
Answers
1
Questions
0
Helped
2793
Points
7

If just found this on another forum:

A few days ago I started the Cruiser and had 4 indicators stay lit.
They were the CHECK ENGINE...SLIP INDICATOR..VSC TRAC..VSC OFF.
Didnt noticed any change in driving and 4-wheel drive is still working.
I removed the negative cable from the battery and the same indicator lights have NOT come back. Everything is back to normal as far as warning lights go. Should I take it in to the service center and have it checked.
Or should I wait to take it in, if it does it again?

  • ecore01 Nov 21, 2013

    Eventually I bought A ScanGauge to scan for error codes (you can check those numbers online to get to know more in detail what caused it) and reset them. It seamed a minor problem with the canister/mixture. Since I drive my FJ Cruiser on LPG that might be the reason. The FJ doesn't recognize the LPG being the classified fuel. It runs just fine for years. Every cycle the error lights pop up. I check the numbers and reset them on my ScanGauge. ScanGauge is worth every buck. It's around 99 bucks and tells you a lot about your precious FJ. Go buy it and connect it to your multi-dashboard-connector.

×

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer

ENGINE CODES

Whenever engine fault codes set, VSC is disabled and lights come on. P0020 shows failing cam shaft position sensor , recommend replace clear codes and recheck. gas spill was coincidental.
0helpful
2answers
0helpful
1answer

Troubleshooting codes p0300, p0301, p0302, p0303,p0305. VSC light, VSC off light, check engine light and engine shaking.

you have multiple cylinder missfire 1,2,3,5 check your spark plugs, plug wires and coils could even be a o2 sensor
0helpful
1answer

Check engine light, vsc light, traction control light on fj cruiser after spark plug change

Like everything else in a computerized vehicle, if the warning lights are on, codes are stored. Get the codes read.
Check engine light on Part Ricks Free Auto Repair Advice
3helpful
2answers

FJ cruiser issue

I had the same thing happen yesterday. I took it to the dealer, and they said the Catalytic Converter was bad and they needed to order a new one. You should take it to the dealer.
5helpful
1answer

Reset Maintenance Required on 2007 Toyota FJ Cruiser

turn ignition to "on"; set your odomoter trip meter display to trip "A" turn off the ignition; hold down trip reset button while turning ignition back to "on" position; hold the button for around five more seconds until it shows a full display of zeroes (ex. "00000000") light should procede to turn off
Not finding what you are looking for?

2,803 views

Ask a Question

Usually answered in minutes!

Top Toyota Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

926 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...