Question about Pontiac G6

2 Answers

Im trying to do my front brakes and I need to know the size of the torque bit to release the caliber to do the brakes I have all the other tools I just dont know what the size of the bit I need is

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,803 Answers

Most of them use a T65.

Posted on May 03, 2011

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Pontiac Master
  • 3,018 Answers

Torques Bit T-65

Posted on May 04, 2011

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to release brake caliper pressure on 2000 nissan sentra


Hi Shelby,what are you trying to do?To release pressure,get a wrench and open up the bleeder valve their,get a rag to catch the fluid.Here's a link to a diagram of the bleeder valve.Also here's another link on bleeding,Is your brakes sticking,you may need a new caliber. Repair Guides Front Disc Brakes Brake Caliper AutoZone com Here's how to bleed. http://www.autozone.com/repairinfo/repairguide/repairGuideContent.jsp?pageId=0996b43f80381ef5 Here's another link on replacing your caliber. Repair Guides Front Disc Brakes Brake Caliper AutoZone com Here's a link to a new caliber. Brake Caliper Front

Aug 26, 2016 | 2000 Nissan Sentra

2 Answers

What size socket does it take to change the front caliber brake pads on a 300M 2000 Chrysler?


14mm I believe? Id just get a cheap set?..standard I think is 3/8ths

Mar 18, 2015 | 2000 Chrysler 300M

1 Answer

Front Wheel Stuck when in reverse


sounds a bit more serious than just brakes, I wouldn't drive it until it's looked at, being a bit dangerous at the moment .

Jan 25, 2014 | Cars & Trucks

1 Answer

2003 s type brake front pad - what tools are need to change the pads


the front pads are pretty straight forward,just a c clamp is sufficient to press the calibers,make sure the brake fluid reservoir cap is off when you do them..just unbolt the calibers from the rotors and they work the same as standard brakes,but the rear calibers at time will need a caliber tool to turn and press the piston simultaneously

Sep 03, 2011 | 2006 Jaguar X-Type

1 Answer

Im bleeding the breaks on a 91 chevy c1500 the front calipers are locking down and not releaseing


First thing to check is the slide pins on the calibers. Make sure they are clean and free of any rust. If not, replace them. If they are not rusty then clean & lubricate them with a very small amount of grease. Your brake system on this vehicle is 20 years old. Have you ever changed the brake fluid? If you are like most people the answer is no. I recommend you flush the entire brake system and install fresh DOT3 fluid. Look closely at the flexible brake hoses that connect to the caliber. They may be collapsing and I recommend you replace them on a 20 year old vehicle. I would also recommend you replace the calibers on the front. With new calibers, brake lines, and fresh fluid you should have great brakes. If you still have the problem replace the master cylinder.

May 27, 2011 | 1991 Chevrolet K1500

1 Answer

Just need to know the bolt head size for caliper hold down bracket for 07 dodge caliber rear brakes


im seeing 13 mm to be the size for those bolts but i would bring a 14mm 15mm 17mm 19mm socket/wrench as well. goodluck

Mar 19, 2011 | Dodge Caliber Cars & Trucks

4 Answers

Brakes need to be bled


Back to front.....rear passenger first then rear driver's....then pass front and then driver's last.

Jun 25, 2009 | 1991 Toyota MR2

1 Answer

Tool for 2006 brake calipers I need size


buy a set of the torque bits they come in sets of 4 or 5

Jun 14, 2009 | 2006 Mazda Tribute

2 Answers

DONT KNOW HOW TO REMOVE THE BREAK CALIBER


To remove the caliper, you need a torx head tool (can't remember exact size) to remove the two slide pin bolts.(inside the two small rubber boots at each end of caliper) After getting them loose, remove the brake hose, then remove bolts and caliper. (don't loose the two copper washers...if they aren't in the new caliper box you will need them.) Check and see if the caliper retracts easily after it is removed. If it does, the rubber brake hose may have internally failed and is your problem. If piston is very hard to move, get a new caliper. Replace both side brake pads, not just side you are workingon. (recommend both calipers as well but most times it works fine with one.
When replacing, make sure slides are free in calipers and thread pins by hand so that you don't cross thread them. After it's back together bleed front brakes and before moving car step on brake to re-set pistons.

May 23, 2009 | 1994 Pontiac Grand Prix

1 Answer

2004 Chevrolet Silverado Extended Cab brake replacement


jack the truck up and take the passangers tire off. look behind the rotor you should see 2 bolts holding the caliber on to the rotor. loosen those and take them out. from there you should be able pull up on the caliber this will take the caliber and pads off together. take the pads out of the caliber and install the new ones .

BECAREFUL not to twist or bend the caliber to much or you will bend the brake line.....

once you have installed the new brake pads in the caliber. put the caliber back on the rotor. if they will not fit release the bleader valve to release the pressure. than you should be able to slid the caliber back onto the rotor. once you have done that close the bleader valve. reinstall the 2 bolts to hold the caliber in place. put your tie back one. Follow these steps for the other side.

now once that is done. you might want to blead the front breaks.
what you do is have someone help you. fill the brake resiviour with brake fliud. than start your truck.
Have someone in the cab to press the brake. What you want to do is turn the wheel so you can get to the bleader valve. once you can get to it open it up. have the person in the cab other truck press the brake until you see a steady flow of brake fluid coming out of the caliber. once you see that have the pseron press the brake once more and hold it to the floor.
close the bleader valve.

now do the same thing on the other side. But, make sure you check your resivour fluid first.
This is to make sure you don't have any air in the lines. after you are done with both side put it in gear and hit the brake make sure you stop......... If that works go about half the block down and hit the brake again to make sure you stop......
once you have done that and are comfortable with the way the truck stops than ou are good to go and now know how to change the brakes for future refrence..... be aware the back brakes are diffrent.........

let me know when you are ready for the back brakes.
do not blead the front ones if ou intend to do the back brakes afterwarwords......

if you are only doing the front brakes you must blead the the passanger side first......... if you do not have the bolts holding your caliber on than you will have a pin the you will take a hammer to and knock it out that will release them....

Aug 01, 2008 | Chevrolet 1500 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...