Step by step instructions for rear bumper cover removal on a 2005 Prius, including bolt and plastic rivet locations.

To remove the rear bumper cover on a 2008 Nissan Quest, you can follow these general steps:

1. Prepare the Vehicle: Ensure that the vehicle is parked on a flat surface and the engine is turned off. Put on safety goggles and gloves to protect yourself during the removal process.
2. Locate the Fasteners: Look for the fasteners securing the rear bumper cover. They are typically located underneath the bumper cover, near the wheel wells, and along the bottom edge of the bumper.
3. Remove the Fasteners: Depending on the specific model and trim level, the fasteners may be screws, bolts, or plastic clips. Use the appropriate tools, such as a screwdriver or socket wrench, to remove the fasteners one by one. Turn them counterclockwise to loosen and remove them. Keep the fasteners in a safe place for reinstallation later.
4. Disconnect Electrical Connections (if applicable): If your Nissan Quest has any electrical connections, such as sensors or lighting, attached to the rear bumper cover, disconnect them carefully. Look for connectors near the edges or inside the trunk area. Gently detach the connectors by pressing the release tabs or using a flat-head screwdriver to release any locking mechanisms.
5. Release the Clips: Once the fasteners are removed, there may be plastic clips or tabs securing the bumper cover to the vehicle's body. Carefully pry or release these clips using a trim removal tool or a flat-head screwdriver. Take care not to damage the bumper cover or the vehicle's body.
6. Remove the Bumper Cover: With all the fasteners and clips released, gently pull or wiggle the rear bumper cover away from the vehicle's body. Start from one side and work your way to the other, ensuring that all connections and clips have been detached. Be cautious of any remaining electrical connections as you remove the bumper cover completely.

Please note that the exact steps and fastener locations may vary slightly depending on the specific trim level and optional features of your 2008 Nissan Quest. It's always recommended to consult the vehicle's owner's manual or a professional technician for more precise instructions tailored to your vehicle.
Take your time during the removal process to avoid any damage to the bumper cover or the vehicle's body. If you're unsure or uncomfortable performing the removal yourself, it's best to seek assistance from a qualified technician or a reputable automotive service center.

Hi Robert,

Please watch videos below and I'm sure it help you !!

https://www.youtube.com/watch?v=JTQLDfumlBw
https://www.carid.com/ford-sport-trac-rear-bumpers/

regards,
Sonu

Remove fender well trim ( a few screws)
Remove front bumper COVER (not the bumper- the plastic cover)
About 14 screws. Mostly on the underside, get a creeper, and a few
on the top.

Remove the (left or right side) Headlight assembly ( a couple more screws).
One assembly contains the headlight, turn signal and running light. Unplug
the electrical connector from the assembly. All bulbs remove from the back
of the headlight assembly. Headlight is held in place by bail wire, smaller
bulbs are 1/4 turn.

2000 Toyota Sienna rear Bumper cover replacement (1998 ...

? 3:40
https://www.youtube.com/watch?v=AY1BBdg3q74
Sep 20, 2013 - Uploaded by SergSpace
2000 Toyota Sienna rear Bumper cover replacement (1998-2003) .... Automotive Bumper Repair Specialist- How to repairyour plastic bumper cover ... Toyota Sienna Rear Shock Installation 2003, 2004, 2005, 2006 - Duration: ... 2015 Toyota Sienna XLE - Duration: 28:13. by MikesCarInfo 35,234 views.

Fixing My Mom's Prius: Loose Rear Bumper Cover - YouTube

Hello, the first thing I would recommend that you buy a repair manual that shows step by step instructions, with illustrations I can't do that here. You'll need some common metric tools and a voltmeter, there are high voltages involved and you will need to wear insulated gloves rated at least to 1000 volts DC to prevent severe injury or possibly death.

The actual replacement is not that difficult:
Disconnect the 12 volt auxiliary battery
disconnect the orange service plug on the hybrid battery and tape the connector on the battery
remove the rear seat and the seat back braces
remove the trunk carpet and the spare tire cover
remove the two orange cables going to the front
measure dc voltage at the terminals where the cables were removed there must be less than 1 volt.
remove the 12 mm bolts that connect the battery to the body including the torx bolt
slide the battery back and have someone help to lift it out.

take help of the following steps to remove rear bumper on ur tucson.

Open the trunk of your vehicle.

1. Unscrew all the screws on the inside plastic trim that covers your bumper to trunk connection.
   
2. Pry the plastic piece out with a flathead screwdriver. You will expose the bolts that attach the rear bumper to the trunk.
   
3. Unscrew the bolts connecting to the inside of your rear bumper. There should be four bolts.
   
4. Unscrew the two to four screws connecting to your bumper from the inside of the rear wheel tire wells. These screws are on the area of the tire well that is closet to the bumper.
   
5. Slide under the rear of your car. Use a flathead screwdriver to pop the plastic rivets out of place along the underside of the rear bumper. There should be four to six rivets.
   
6. 
   Squat behind your car and firmly pull the bumper off. There will popping plastic sounds, this is the pop-in-place plastic rivets that are the last pieces that hold your rear bumper in place.
   

1. Open liftgate. 2. Remove both taillight assemblies by removing 2 hex-head bolts located in the area revealed when the liftgate is opened. 3. Remove 4 plastic retainers on the very bottom of the bumper cover in the rear. 4. Remove 2 phillips head screws in the wheel well rear lip. 5. Remove 4 pop-up plastic retainers in liftgate area. Use two screw drivers to lift the head and then pull the entire retainer out. 6. Remove a hex-head bolt from each side in the area revealed when the taillight assembly was removed. 7. Bend the bumper cover outward on each side to clear the wheel well lip and remove the bumper. Have a blanket or carpet on the ground to protect the bumper. 8. Remove metal clips from tabs that connect the upper bumper cover to the lower bumper cover. 9. Drill out pop-rivets that connect upper bumper cover to lower bumper cover. 10. Push tabs out of slots to separate the upper and lower bumper covers. 11. Release tab locks on chrome trim pieces and remove from upper bumper cover. 12. Reverse this process to replace the bumper cover.

Hello, I can assist you. Begin by rounding up the necessary tools:

7mm socket and ratchet
7mm wrench
10mm socket
screw driver or panel removal tool (for push rivets)
Now go to the following site and take a look at the step by step instructions and pictures which does a nice job of explaining this entire job. Thanks for using Fixya!
http://www.jeeppatriot.com/forum/showthread.php?t=6291

There are plastic rivets taht need to be pull and possibly to be cut. and there should have 2-3 bolts per side which need to be removed. The rivets or clips can be purchase at the dealer or local Automotive store, such as autozone and etc.

Here's some instructions for removing bumper and headlights.

E-Class W211 front bumper removal (standard body style).

Tools needed:
- Automotive wheel ramps (Rhino ramps from Autozone).
- 1/4" drive socket set with 8mm and 10mm sockets.
- #20 torx bit.
- Floor jack, optional but useful.
- Flat blade screwdriver.

Instructions for bumper removal:

1) Turn front wheels full right to remove push-pin fastener at lower front corner of left wheel well plastic splash guard. It's difficult to remove this fastener once the car is up on the wheel ramps.

2) Turn front wheels full left to remove push-pin fastener at lower front corner of right wheel well plastic splash guard.

3) Drive car up on wheel ramps. Block rear tires. Open hood.

4) Remove lower mesh plastic grille. There are five attachment points on the top edge of the grille. You can get to three of them with your hand by reaching between the radiator and the back side of the grille. The two outer ones can be released with a screwdriver also reaching in between the grille and radiator. Once the plastic tabs are released, you can remove the grille by pulling it out from the front of the car.

5) Remove the plastic panel located immediately behind the bumper from the bottom of the engine compartment. This panel is held in place with nine sheet metal screws with a 8mm hex head. Five screws are on the bottom of the car and there are two screws in each wheel well at the inner lower edge. After removing all nine screws you can work the panel free.

6) Disconnect the cable from each fog light and remove both fog lights. They are held in place by two sheet metal screws with a #20 torx head.

7) Remove the side marker bulbs. The one on the passenger side turns clockwise to remove and the one on the driver side turns counter-clockwise.

8) Remove the temperature sensor from its socket on the driver side.

9) If you have a floor jack, raise the car at the jack point on the cross member below the engine. You do not want to raise it off the wheel ramps. But it helps to have more clearance above the tires to work in the front wheel wells.

10) Remove three of the plastic nuts holding the forward half of the plastic wheel well liner in place. It's not necessary to remove the plastic liner. You just need to loosen it up so that you can pull it away from the fender to gain access to the screw and bracket securing the bumper to the fender.

11) Pull back the wheel well liner and remove the sheet metal screw from the rear end of the metal bracket . There is only one sheet metal screw (#20 torx head) holding this bracket in place. Don't attempt to remove the bracket yet. I used a #20 torx bit in a 1/4" socket with a 6-inch extension for a 1/4" drive wrench. The head of the screw faces the ground.

12) Remove the 5mm bolts (8mm hex head) holding the bumper to the headlight assembly between the small lens and large lens (both sides).

13) Remove the two 6mm bolts (10mm hex head) on either side of the large grille area opening.

14) Remove the two 6mm bolts (10mm hex head) securing the bumper to the bottom edge of the crashbar. You can access these bolts through the front where you removed the plastic mesh grille.

15) Remove the three 5mm bolts (8mm hex head) holding each headlight assembly in place. Two longer bolts are on top. One at the rear outer corner and one at the front inner corner. The third bolt is accessed from the bottom. It's in the area above the fog lamps. You don't need to disconnect the headlight cables and remove the assembly. But it helps to allow the headlight assembly to "float" freely while you disengage the bumper from the fender.

16) At this point all of the fasteners holding the bumper in place have been removed. The only thing left to do is to remove the two brackets "clamping" the bumper cover to the lower front edge of the front fenders. Before you do this, position some cardboard boxes, bags of packing material, six packs of paper towels, or other suitable items to protect the bumper in case it falls off the car.

17) The bracket holding the bumper cover to the fender has a "pin" that slips into a slot at the front edge of the bumper cover. There is a matching slot near the front edge of the fender. It's not possible to see this pin from the bottom of the car. Use a flat blade screwdriver to pry the bracket away from the bumper/fender and towards the center of the car. The bracket will "hinge" on the pin at the front end of the bracket. After you swing the bracket away from the bumper, you need to slide it forward to remove it from the slot in the bumper cover and fender. You will probably scratch some paint off of this bracket with the screwdriver. I recommend repainting the scratched areas of the bracket before reinstalling it.

18) After removing the bracket from each side of the car you need to deal with the small plastic "hook" holding the bumper cover to the very front tip of the fender. This hook is an integral part of the bumper cover. Disengaging this hook from the fender is probably the most difficult step of removing the bumper. Simultaneously raise the head light assembly slightly, push the leading edge of the fender outward slightly, and push the bumper cover inward toward the headlight assembly. Don't get too aggressive with the fender. It's aluminum and you will make a real mess if you apply too much pressure on the fender. It took me about 20 minutes to free each side from this hook. It should take you less time, since you now know that the hook exists!

19) Gently pull the bumper forward and away from the car. This is one step where a second person would be helpful. But I did manage to do this step alone. There is a "pulley" like attachment point on each side just below the fender/bumper seam.

To re-install the bumper, reverse the order of the steps above. When re-installing the bracket between the bumper cover and fender, I smeared a thin coating of car wash soap on the bracket to facilitate snapping the bracket back into place.