Question about 1995 Cadillac DeVille

1 Answer

Transmission not shifting diagnozed as input speed censor.Is it in the trany or on the trany?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.


    An expert who has answered 20 questions.

  • Expert
  • 41 Answers

The speed censor is on the side of the tranny it has a two wire pluggin going to it.speed censor are pretty easy to put in ,they just tread in to the side of the tranny.

Posted on Apr 05, 2011


1 Suggested Answer


6ya staff

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where does the turbine input shaft speed sensor go on a 2010 cevy malibu Lt

Chances are that this sensor is located in the transmission or has access to it outside the housing.Take the car to a transmission specialist and have them give you an estimate.Most dealerships these days don't even do trany work anymore so save yourself some money and go directly to someone who can help you.good luck

May 22, 2014 | 2010 Chevrolet Malibu

1 Answer


did the trans come with the proper fluid(recommended by Chrysler) and level. was the whole system flushed? Reused sensors could be an issue if one or more is faulty.

Jun 27, 2013 | 2005 Dodge Dakota Club

1 Answer

Engine light goes on and my transmission starts acting up chevy malibu 1998

Input shaft speed sensor or out put speed sensor . Have the vehicle checked for DTC'S - diagnostic trouble code's . This would probably point you in a diagnostic direction .

Dec 08, 2017 | 1998 Chevrolet Malibu

1 Answer

Trany problems

either ur torque converter isnt geting fluid or one of the valve bodys in blocked and not gettin fluid through thats what im thinking, or could be ur linkage needs adjustin ya . derrick

Dec 08, 2009 | 1991 Ford F150

1 Answer

I have switched my motor to carberated and put a different automatic transmission in also and the trany will not shift. i put it in overdrive and it stays in first gear and if you shift it manually into...

The transmission should have a vacuum line going to it. It needs this vacuum to shift into the next gear. Try locating it and connect a vacuum line from the carb to the trans.

Dec 08, 2009 | 1991 Ford F150

2 Answers

Speedometer quick working suddenly and transmission will not shift out of first while in drive or manualy

speed sensor may be faulty and may prevent the transmission from upshifting. This will also prevent the speedometer from working. Hve the spped sensor's circuit checked, and the spped sensor itself. Replace if necessary. Hopefully this helps

Aug 12, 2009 | 1999 Mitsubishi Eclipse

1 Answer

Code p0733, p0717

P0733 Trany Ratio in gear 3. This is a trany fault code and the first thing you should check is your tps sensor using your DVOM meter. Measuring the voltages between idle and WOT (wide open throttle), there should be no interruption in the reading (or glitches). Otherwise, it can play havoc to your shifting cycles which can cause this code P0733. If there are glitches, replace the tps sensor right away and reset the code. If trany is suspected, most common fix for this points to a defective valve body. To verify, it can be done by using a scanner which has the capacity to command the trany solenoids so it can be tested at various trany operating pressures. P0717 is a improper signal from your pules generator A. Which is a the turbine speed sensor on the transmission, You have two of them, the A reads the speed of the input shaft of the transmission and the B sensor reads the output shaft of the transmission. I know with the P0717 it will put the transmission in the limp mode and will not shift past 3rd gear and if your running the transmission hard on third you may have triggered the P0733 which is the 3rd gear slipping. Check the transmission fluid and make sure you have not burnt the fluid, if the transmission fluid is burnt you may want to have a transmission repair shop replace the turbine speed sensor (Pules Generator A) and the fluid and filter. Cross the fingers and hope the transmission was not ran to hard in third causing damage to the third gear clutch packs. Good luck and keep me posted, be glad to help.

Jun 15, 2009 | 2002 Hyundai Accent

1 Answer

Intermitten hard shift 1-2, 2-3, flare shift into 4th

The trani is electronically controlled. without a diagnostic computer you are not going to know. It may be the speed sensors (for the trani.) but thats a guess. how long since the last trani service. Fluid level and condition can affect its perfomance. Good luck.

Apr 29, 2009 | 2003 Acura 3.2TL

2 Answers

Jeep liberty transmission problem


Aug 22, 2008 | 2003 Jeep Liberty

Not finding what you are looking for?
1995 Cadillac DeVille Logo

Related Topics:

205 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts


Level 3 Expert

85222 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides