Need belt routing diagram for 01 chevy silverado 2500hd with 8.1 liter v8

Different model year shown but it is the same engine. The diagram should also be located on the shroud above your radiator. 2006 Chevrolet Silverado 3500 V8 8 1L Serpentine Belt Diagram...

There is usually a belt route guide under hood on the cross piece that runs across the radiator.

Pop the hood of the car and locate the serpentine belt routing diagram. The diagram on the 2003 Chevrolet Impala is on top of the fan shroud. The diagram will be a picture of all of the accessory pulleys and how the serpentine belt is routed among the pulleys. This diagram will give you the exact direction for routing the new belt onto the pulleys. If you cannot find a serpentine belt routing diagram, take a notepad and pen and draw out the exact routing diagram of the old belt across the pulleys.

2 Locate the serpentine belt tensioner. It is located below the alternator on the left front side of the engine. The tensioner on the 3.4 liter, 3.5 liter and the 3.9 liter engines will require a 3/8 ratchet to release the belt tensioner. The 3.8 liter engine will require a ratchet and a 15 mm socket for the belt tensioner. Rotate the belt tensioner clockwise to loosen and remove the belt from the belt tensioner pulley.

3 Slide the old belt from the belt tensioner pulley. Remove the belt from the remaining pulleys and pull the belt from the engine compartment.

4 Route the new belt across the crankshaft pulley first. The crankshaft pulley is the big pulley on the bottom of the engine in the center. Then route the serpentine belt across the remaining pulleys as directed by the serpentine belt routing diagram. Leave the belt tensioner pulley for last.

5 Rotate the belt tensioner clockwise again to relieve the tension and slide the new belt across the top of the belt tensioner pulley. Release the belt tensioner and the belt will tighten up as the tensioner applies pressure to the belt. Make sure the new belt is properly seated in all the pulleys.

6 Crank the engine and inspect the belt again to make sure that it stays seated in the pulleys.

Read more: How to Replace a Serpentine Belt on a 2003 Chevrolet Impala ' eHow.co.uk http://www.ehow.co.uk/how_6120665_replace-belt-2003-chevrolet-impala.html#ixzz1Yi6QLAjb

DRIVE BELT ROUTING DIAGRAM IS ON THE RADIATOR SUPPORT.OR GO TO AUTO ZONE OR ADVANCE AUTO PARTS.THEY WILL PRINT BELT DIAGRAM FREE.

1997 FORD MUSTANG - V8 4.6L 281ci GAS FI N V
Belt Routing Diagram Multiple Accessory





1997 FORD MUSTANG - V8 4.6L 281ci GAS FI N X
Belt Routing Diagram Multiple Accessory



Hope this help (remember rated and comment this).

this should help you, please leave a good feedback thankyou and good luck.

try to jump the starter selinoid

here are 4 diff. type of diagram.
Depend on how many pulley you have.
Let me know if this help you.

HI. you can view an image of the routing by clicking the link below.

CLICK HERE FOR ROUTING.

UNDER THE HOOD IS A DIAGRAM OF HOW THE BELT IS ROUTED. TAKE NOTE OF THE WHITE STICKER ON THE FAN SCHROUD, JUST ABOVE THE FAN. THE TENSIONER PULLEY IS THE ONE YOU NEED TO ROTATE IN ORDER TO RELEASE THE TENSION ON THE BELT FOR REMOVAL. USING A 15 OR 16 MM SOCKET, ROTATE THE TENSIONER UNTIL YOU RELIEVE THE TENSION AND SLIDE THE BELT OFF ONE OF THE SMOOTH PULLEYS. THEN RELEASE THE RATCHET EASY SO IT DOESN'T SPRING BACK UP. UNRAVEL THE BELT AND INSTALL THE NEW ONE USING THE DIAGRAM. JUST A HINT: IF THE PULLEY HAS RIDGES THEN THE BELT HAS TO BE ON THE RIDGED SIDE OF THE BELT, IF IT HAS A SMOOTH PULLEY, THEN IT RIDES ON THE OUTSIDE OF THE BELT. WHEN YOU ALMOST HAVE THE BELT ON THE LAST PULLEY, ROTATE THE TENSIONER AGAIN AND SLIDE THE BELT ON THE LAST PULLEY. IT HELPS IF THE LAST PULLEY IS A SMOOTH ONE. HOPE THIS HELPS ENOUGH TO FINISH THE JOB. PLEASE KEEP ME POSTED. THANKS FOR AN HONEST RATING AND FOR USING FIX-YA. GOOD LUCK.