Torque specs for head on 2.4 dohc motor - Hyundai Motor 2004 Sonata

Hi,

If this is for a mazda vehicle, please call mazda for the specs at (800) 866-1998 Thank you.

What are the torque specs for the rod bearings on a 2006 - Fixya

https://www.fixya.com > ... > 2006 Dodge Caravan
Nov 15, 2019 - What is the torque specification for the inner tie rod 1996 .dodge caravan 2.4 liter. 45-55 foot pounds. Read full answer. Sep 18, 2012 • 1998 ...
SOLVED: Torque chart for dodge caravan 4l - Fixya
Sept 9, 2019
Main bearing torque spec for Dodge Grand Caravan 2005
Sept 15, 2019
Im trying to find the connector rod bearing torque - Dodge - Fixya
Jul 15, 2018
Head bolt torque specs for 2.4L dohc dodge caravan - Fixya
Jun 2, 2012
More results from www.fixya.com

Dodge Caravan 2.4 need engine tightening specs and head ...

https://www.justanswer.com > chrysler > 28qv6-dodge-...
Jun 27, 2009 - SPECIFICATIONS - TORQUE ; Balance Shaft Carrier Cover-Bolts, 12, - ; Camshaft Sprocket-Bolt, 101, 75 ; Connecting Rod Cap-Bolts, 27 +¼ turn, 20 +¼ ...
1 answer · Top answer: Here are the head bolt specs: Before installing the bolts, the threads should be coated with ...

Torque Specifcations - MAHLE Aftermarket

https://www.mahle-aftermarket.com > media > torque3
PDF
Engine Model Year. Rod Torque. Main Torque. Cylinder Head Bolt Torque. CASE. 2.4. 148. 61-66. 45-50 FT/LBS. 90-100 FT/LBS. 60-65 FT/LBS. CASE. 2.4.
124 pages
You've visited this page 3 times. Last visit: 01/02/22

Repair Guides Specifications Torque Specifications AutoZone com

If you need further help, I’m available over the phone at https://www.6ya.com/expert/michael_2496c4f07ad24453

Quote:





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.

• Hi, I can help.
• The torque sequence for the head of a 1996 Hyundai Elantra 1.8 dohc is indicated in the diagram below as well as the torque specs I have listed.

• M10 bolts tighten to 22 foot lbs.
• M12 bolts tighten to 26 foot lbs.

• If you have any comments please feel free to leave them here.
• Hope this helps and thank you for using FixYa.

Regards, Tony

2001 Daewoo Nubira 2.0L MFI DOHC 4cyl

The Head Bolt Torque ...

Torque sequence ------------------------- Front | 10 6 2 3 7 | of | 9 5 1 4 8 | Engine --------------------------

Step 1 - Torque to 18 ft/lbs Steps 2 - Turn 90 degrees Steps 3 - turn 90 degrees Steps 4 - turn 90 degrees Recheck final torque in sequence


Hope helps (remember rated and comment this).

for the 2.2L OHV:
(pully 8 4 1 5 9 <-- long bolts @ 63Nm (46ft/lb)
side ) 7 3 2 6 10 <-- short bolts / 10 is the stud @ 58Nm (43ft/lb)

for the 2.4l dohc are as follows:
(pully 9 3 1 5 7
side) 10 6 2 4 8
bolts 1-8 torqued to 65Nm (40ft/lb)
bolts 9-10 torqued to 40Nm (30ft/lb)

then (either engine) give each an additional 90° (¼) turn

it's best to do the tightening in stages, you don't want to go completely tight on the first pass or there will problems and you'll get to do it all over again

Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): Foot pounds (Final torque) Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. Foot pounds (Final torque) Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

hi bob
head torque on the 2.0 DOHC is 64 ft lbs , done in two -three steps , also there is a sequence for proper order . here is a very good description with graphics .

1999 kia sportage 2.0 DOHC head torque

Thanks for using FIX YA !

J5