2004 chevy trailblazer 4 wheel drive front axle lock nut torque setting

Question edited for clarity.
Question moved to model category.

2006 Toyota tundra 4.7L Front End Torque Specs

toyota-specs.com https://toyota-specs.com > cars > 2006 > tundra4.7 > t...
Toyota Tundra Front Axle Nut Torque Spec : 203 ft-lbs · Toyota Tundra Wheel Hub Torque Spec : 100 ft-lbs ...

BHA53102 Axle / Spindle Nut Torque Specification

1A Auto https://docs.1aauto.com > BHA53102 Torque S... PDF Toyota. 4Runner. 1996-02 4 Wheel Drive. Front. 174. 236. Toyota. Sequoia ... Tacoma. 2001-04 4 Wheel Drive. Front. 173. 235. Toyota. Tundra. 2000-06 4 Wheel ...
1 page
https://www.google.com/search?q=2006+Toyota+Tundra+4x4+front+axle+torque

..

1995 C1500 spindle nut torque procedure? - CK5 Network

https://ck5.com > ... > General Discussion > The Garage
Jan 31, 2005 - while rotating the hub in a foward direction torque the nut to about 12ft lbs. Keep doing that a few times to ensure the bearings are seated.

96 gmc: torque..the front spindle nut..C1500 - JustAnswer

https://www.justanswer.com > Car Questions > GM Repair
Sept 16, 2011 - Torque nut (12) 10-12 ft lbs while turning the wheel assembly forward by hand. This will seat the bearing. Loosen nut (12) to a just loose ...
1 answer · Top answer: You can attach the magnetic base to the end of the spindle or to the brake caliper bracket. ...

• 
  

  1996 chevy: the torque setting for front wheel bearing..1500 4x4

  https://www.justanswer.com > chevy > 1tv6x-1996-che...
  Feb 18, 2009 - Outer Tie Rod Nut (C and K Models) · Shackle to Frame Nut and Bolt (C3500HD) · Shock Absorber Nuts (K Models) ; 62 N·m · 95 N·m · 90 N·m ; 46 lb ft.

Torque specification guide - PDF4PRO

https://pdf4pro.com > cdn > torque-specification-...
PDF
Front and rear axle nut torque specifications for FWD, RWD and 4 W/D vehicles. Torque specification guide. Form #457377. April, 2007.

The one that fits!

That's not the way it works. you buy a socket set. It has one set of AF Sockets and one set of Metric sockets. The one you use is the one that fits.

Hub and Wheel Bearing Torque Specifications - DRiV

drivcat.com > HubWheelTorqueTableWindow

2009 Ford Fusion ... Front Proc 1 Note ... Front Proc 2 Note ... Do not attempt to tighten the nut with the vehicle on the ground or the wheel bearing will be ...

Front Axle Nut Torque Spec - Lounge - Fusion Energi - Ford ...

www.fordfusionenergiforum.com > topic > 6160-front-...

Dec. 2, 2019 - Im replacing the front wheel bearing assemble this weekend and cant find the torque spec for the ale nut. The older model Fusion (up to 2012) ...

BHA54317 Axle / Spindle Nut Torque Specification - 1A Auto

docs.1aauto.com > BHA54317 Torque Spec

PDF Vehicle Notes. Lb. ft NM. Ford. Fusion. 2006-12 (Excluding All Wheel Drive Models). Rear. Lincoln. MKZ. 2007-12 (Excluding All Wheel Drive Models). Rear.

SKF-Front-Rear-Axle-Nut-Hub-Mount-Lug-Nut-Torque-Spec

dannysengineportal.com > wp-content > uploads > S...
PDF
Front & rear axle nut, hub mount and lug nut torque specifications for FWD ... 3 Series AWD E92, E93 ....2012-2013 . ... FORD / MERCURY TRUCKS - cont.


..

i usually put lock tight blue on them and tore to 65 ft lbs the nut on the axle i usually tore to 50- 60 ft lbs no lock tight

Usually a front speed sensor/wheel hub going bad. is there a humming noise from the front end area while driving at highway speeds? If there is, try to isolate which side it is, and have that hub bearing replaced and make darn sure the axle nut is torqued to the proper spec, or it will fail. To many auto techs just tighten them up withan impact gun, and say its good.

Here are the front axle nut torque specs for the 2004 Chevy Silverado 2500HD:
• Axle Shaft nut - 177 ft-lb
• hub and bearing assembly to steering knuckle bolts - 133 ft-lb

maby im wrong but if you rev up and only rear wheels spin that means that it might be 4 wheel drive but not constant 4 wheel drive or diff lock system ,,,, ,, in 4 wheel drive all wheells will turn together but if pressure of slip is bad enough or torque high enough only 2 wheels will drive ,,, thats why diff lock locks wheels together in each axle to over come this ,,, all wheel drive like in landrover locks all 4 wheels together to ensure all wheels rotate to give best grip

Spindle nut. Tighten the nut to 185 ft. lbs. (251 Nm). Inch pounds is not an option, this critical torque spec is FT lbs.

IT COULD BE A FUSE THERE ARE FUSES UNDER THE HOOD FOR 4 WHEEL DRIVE ALSO IF THAT DOED NOT WORK CHECK 4 WHEEL DRIVE SELINOID