Need to know crankshaft main bearings and rod bearings torque specks.

already answered here, 26 or 29 :>D

What are the torque specs for crankshaft main and rod - Fixya

https://www.fixya.com > ... > Buick > LeSabre
Sept 21, 2012 - The connecting rods torque to 29 foot pounds. ... Where is the eng control module in a 2005 Buick Rendezvous ultra 3.6 eng.
SOLVED: I need torque specs. for rod bearings and main - Fixya
Jun 2, 2011
Torque specs for intake on 2005 buick rendezsous - Fixya
Sept 7, 2019
Torque spec for1997 3.8 buick rod and mains - Fixya
May 22, 2012
What is the torque specks for a 3.8 lt v 6 rear main cap 1987 buick ...
Nov 14, 2019
More results from www.fixya.com

More here

https://www.google.com/search?q=05+Buick+Rendezvous+Ultra+3.6+piston+rod+torque
..

Torque settings for V-6 engine.
Main bearing cap bolts torque:
Torque: 27 N·m (275 kgf·cm, 20 ft·lbf)
Mark the front of the main bearing cap bolt with paint.
Re tighten the main bearing cap bolts by 90 degrees.
Check that the crankshaft turns smoothly.

Connecting rod cap bolts torque:
Torque: 24.5 N·m (250 kgf·cm, 18 ft·lbf)
Mark the front of the main bearing cap bolt with paint.
Re tighten the main bearing cap bolts by 90 degrees.
Check that the crankshaft turns smoothly.

main bearings torque is 18 ft lbs. plus 90 - 94 degrees, rod bearings torque is 13 - 16 ft lbs. plus 90 - 94 degrees.crankshaft damper bolt torque 80 - 94 ft lbs, fly wheel bolts torques 94 - 101 ft lbs.

TORQUE SPEC FOR ROD BEARING BOLTS 19 - 24 FT LBS TORQUE SPEC FOR MAIN BEARING BOLTS 60 - 70 FT LBS, CRANKSHAFT PULLEY BOLT 85 - 100 FT LBS. MAIN BEARING OIL CLEARANCE .0005 - .0022 CONNECTING ROD OIL CLEARANCE .0008 - .0015 / SHAFT END PLAY .004 - .008 / AND ROD SIDE CLEARANCE IS .004 - .011 HOPE THIS HELP THIS INFORMATION I GAVE YOU IS INLINE 6 -200 AND INLINE 6 - 250 ENGINES

FOR 1979 ROD BEARINGS TORQUE IS 40 FT LBS MAIN BEARINGS 100 FT LBS. FOR 1981 MODELS. ROD BEARINGS TORQUE IS 40 FT LBS. AND MAIN BEARINGS 100 FT LBS. CYLINDER HEAD BOLTS 80 FT LBS. CRANKSHAFT PULLEY BOLT 225 FT LBS. FAN PULLEY TO BALANCER 20 FT LBS.

CRANK SHAFT PULLEY BOLT TORQUE IS 83 FT LBS. MAIN BEARINGS TORQUE IS 48 FT LBS ROD BEARINGS TORQUE 23 FT LBS. YOU NEED A BEARING SEQUENCE GET PIECE OF PAPER WRITE NUMBERS 9 5 1 3 7 AND UNDER THIS NUMBER LINE NUMBERS UP ON EACH OTHER WRITE DOWN NUMBERS 8 6 2 4 10 YOU HAVE 10 CRANKSHAFT MAIN BEARING BOLTS. WHEN YOU LINE UP BOTH NUMBERS YOU WILL START TIGHTEN BOLTS 1 AND 2 TIGHTEN BOLTS 3 AND 4 TIGHTEN BOLTS 5 AND 6 TIGHTEN BOLTS 7 AND 8 TIGHTEN BOLTS 9 AND 10 YOU ARE TIGHTEN BOLTS IN A CRISS CROSS PATTERN. BESURE TO POUR OIL OR LUBRICATE CRANKSHAFT AND BEARINGS WITH CLEAN ENGINE OIL.WHEN YOU TORQUE MAIN BEARINGS TORQUE ALL THEM TO 20 FT LBS AND SECOND PASS TORQUE ALL BOLTS TO FINAL TORQUE 48 FT LBS. IF YOU RUN TO ANY PROBLEMS. YOU CAN BUY A HAYNES REPAIR MANUAL IT CAN HELP YOU.

MAIN BEARINGS BOLTS TORQUE 75 FT LBS ROD BEARINGS TORQUE 20 FT LBS + 70 DEGREES. CRANKSHAFT PULLEY DAMPER BOLT 70 FT LBS

Head bolts, 105-112 Foot pounds (Final torque)
Final torque must be reached in 3 equal steps. Recheck final torque in sequence.
Main Bearing Caps, Torque in sequence Step 1: torque to 50 Ft/Lbs Step 2: torque to 105 Ft/Lbs
Rod Bearing Caps, 45 Foot pounds (Final torque)

hi 1999 chevy malibu head bolts 1-8 40 ft lbs bolts9-10 30 ft lbs tighten all bolts an additional 90 degrees

rod bearings 18 ft lbs plus additional 80 degrees

head
top row of bolts 9 3 1 5 7 bottom row 10 6 2 4 8 from left to right