Looking for OBD codes chevy trailblazer 2004. codes p0128,p1680

p0016
P0016 OBD II Trouble Code Camshaft Position Camshaft Position Correlation...
p0128
P0128 OBD II Trouble Code Coolant Thermostat Coolant Temperature Below...
p0206
P0206 OBD II Trouble Code Injector Circuit Malfunction Cylinder 6...
p0306

P0306 OBD II Trouble Code Cylinder 6 Misfire Detected

p0436

P0463 OBD II Trouble Code Fuel Level Sensor Circuit High Input...

P0128 OBD II Trouble Code Coolant Thermostat Coolant Temperature Below...

Coolant Thermostat

P0128:
P0128 OBD-II Trouble Code
Technical DescriptionCoolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature)

What does that mean?This means that the engine's PCM detected that the engine has not reached the required temperature level within a specified amount of time after starting the engine. The intent of the P0128 code is to indicate a faulty thermostat. Similar codes: P0125

In determining the engine did not reach a "normal" temperature, it takes into account the length of time the vehicle has been running, the intake air temperature (IAT) sensor reading, the engine coolant temperature (ECT) sensor reading, and the speed of the vehicle.

CausesA code P0128 may mean that one or more of the following has happened:

Low engine coolant level .
Leaking or stuck open thermostat .
Faulty cooling fan (running too much) .
Faulty coolant temperature (ECT) sensor.
Faulty intake air temperature (IAT) sensor .Here's a link on replacing your thermostat.

CODE B0055 IS A OEM CODE HAVE UR DISTRIBUTOR AND WIRES LOOKED AT.
CODE P0172 / BAD OXYGEN SENSOR -FUEL LEAK or BEND LINE -DIRTY INJECTORS or( dirty oily air sensor )chk them all
CODE P0106 BAD MAP SENSOR OR A HOLE IN UR (AIR INTAKE) BACK TO THAT AGAIN

Chevrolet OBD Fault Codes
DTC P1680 - Driver 5 (ECU malfunction)

This is any internal ECU problem (ECU = ECM = PCM device); check other details HERE; keep in mind that its possible that you have to reprogramm the ECU.

Here is a bulletin for this problem.Subject: Service Engine Soon Light On, P1680 (Reprogram or Replace PCM)

Models:
2004 Buick Rainier
2004 Chevrolet Trailblazer
2004 GMC Envoy
2004 Oldsmobile Bravada with 4.2L Engine (VIN S - RPO LL8)

Some customers may comment on the Service Engine Soon Light coming on. Upon investigation, the technician may find a P1680 diagnostic trouble code Check the resistance of the accelerator pedal position sensors using the procedure in the appropriate Service Information for DTC P1680.

If the resistance of the accelerator pedal position sensor is within the specifications shown in the Service Information and the vehicle was built prior to the following VIN breakpoints, then reprogram the PCM with the latest calibration.

If the resistance of the accelerator pedal position sensor is within the specifications shown in the Service Information and the vehicle was built after the following VIN breakpoints, then replace the PCM. If the resistance of the accelerator pedal position sensor is outside the specifications shown in the Service Information, then continue with the diagnostics for DTC P1680.

VIN Breakpoints
• Vehicles built at Oklahoma City Assembly Plant - 46192755
• Vehicles built at Moraine Assembly Plant - 42315833

Hope this help

You have to reprogramm the ECM. Here is a bulletin for this problem.
Subject:
Service Engine Soon Light On, P1680 (Reprogram or Replace PCM)

Models:
2004 Buick Rainier
2004 Chevrolet Trailblazer
2004 GMC Envoy
2004 Oldsmobile Bravada
with 4.2L Engine (VIN S - RPO LL8)

Some customers may comment on the Service Engine Soon Light coming on. Upon investigation, the technician may find a P1680 diagnostic trouble codeCheck the resistance of the accelerator pedal position sensors using the procedure in the appropriate Service Information for DTC P1680.

If the resistance of the accelerator pedal position sensor is within the specifications shown in the Service Information and the vehicle was built prior to the following VIN breakpoints, then reprogram the PCM with the latest calibration.

If the resistance of the accelerator pedal position sensor is within the specifications shown in the Service Information and the vehicle was built after the following VIN breakpoints, then replace the PCM. If the resistance of the accelerator pedal position sensor is outside the specifications shown in the Service Information, then continue with the diagnostics for DTC P1680.

VIN Breakpoints
• Vehicles built at Oklahoma City Assembly Plant - 46192755
• Vehicles built at Moraine Assembly Plant - 42315833

Hope help with this (remember rated this).

P0128 is coolant operating temperature operating too low. This can be contributed to the Thermostat stuck open or faulty electronic radiator fan clutch. This is common, I had the same issue and replaced the thermostat and fan clutch and had the clutch re-programmed (required) at the dealer. As for the P0410, check the air pump fuse, if blown it will set this code on. Also check the air pump hoses for water and cracks. Hopefully this helps!!

change thermostat

Replacing it is the only fix. Sounds like it may be sticking open slightly.