Question about 1998 Ford Windstar

1 Answer

Need to put passenger miror on. i need help to show me how to take the door panel off.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 60 Answers

Section 01-05: Trim, Interior 1998 Windstar Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 01/22/1999 Trim Panel, Door Front
Removal

  1. Remove door latch cover by prying from top edge and pulling trim free of retaining clips and sliding trim away from latch.
  1. Remove portion of armrest containing door lock switch and window regulator control switch (14529) by pulling straight up.
  1. Remove rear view outside mirror mounting hole cover assembly by prying at top and pulling upward to release double-sided clip.


    Trim Panel


    need to put passenger miror on. i need help to - ar0885a.gif


    Item Part Number Description 1 23942 Front Door Trim Panel 2 56908-S58 Screw (1 Req'd), Right Door 56906-S58 Screw (1 Req'd), Left Door 3 18B978 Radio Speaker Grille Name Plate 4 56911-S58 Screw (1 Req'd) 5 17D720 Cover Assembly Rear View Outside Mirror Mounting Hole
  1. Remove screw attaching front door trim panel (23942) to front door (20124) under switch plate.
  1. Remove two screws located at bottom of front door trim panel.
  1. Disconnect the door lock switch (14028) and window regulator control switch electrical connectors.
  1. Remove door window regulator handle if equipped by unsnapping and pivoting away the handle cover from base to expose retaining screw. Remove screw from the door window regulator handle.
  1. Pull front door trim panel from the top to release hooks from front door .
  1. Remove front door trim panel.
Installation
  1. Replace any bent or damaged fasteners.
  1. Follow removal procedure in reverse order.
Body Side
Removal
  1. Remove door handle retaining clip by sliding a shop towel between handle and door trim. With tension on the cloth, pull one end of the cloth so it slides between the handle and the door trim. If handle does not come out, reverse direction.
  1. Unfasten 13 christmas tree fasteners using double-acting spring-loaded trim removal tool and pull body side trim panel from body side door.
  1. Remove forward and rearward mating sections from under window trim.
Installation
  1. Replace all christmas tree fasteners.
  1. Follow removal procedure in reverse order.
  1. For installation of handle, install clip to handle, then push handle onto shaft to snap in place.



Back
Removal
  1. Disconnect rear window defroster wires.
  1. Remove the liftgate window garnish moulding as described.
  1. Remove screws attaching liftgate handle to liftgate and liftgate inside trim panel.
  1. Using Rotunda Windshield and Moulding Trim Removal Kit 107-R0401 or equivalent, pry pushpins retaining liftgate trim from the liftgate.
  1. Remove liftgate trim.
Installation
  1. Follow removal procedure in reverse ordneed to put passenger miror on. i need help to - r10441a.gifr />
    Liftgate


    r10441a.gif

Posted on Mar 08, 2011

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove driver side mirror and frame and driver side door panel


You have 3 screws on the buttom panel and some push pins after remouving screws just pull and it will come of then 3 bolts for your miror

Jul 14, 2014 | 1992 Chevrolet K1500

1 Answer

To replace sidemiror


pull inside door panel unbolt miror replace with new one

Aug 31, 2013 | 1997 Chevrolet S-10 Pickup

1 Answer

Power windows locks and mirrors


Sounds like the master switch is not plugged in properly, this is the switch in the driver's door.

Jun 07, 2012 | Cars & Trucks

1 Answer

I have a 200 Mercury Sable, my passenger auto lock and unlock have quit working. Is there a fuse that I need to check and if so where is the fuse panel I need to check. I see a compartment on the...


No fuse just for that door , has one fuse that power's all door lock's. Wiring problem or the door switch or the lock actuator . Look inside the rubber flex boot from the body to the door , opening an closing the door a few hundred time's can cause wires to break. If no broken wire's there , pull the switch off the door panel an test power an ground circuit's . Videos on youtube showing how to diagnose these type problems .

Nov 23, 2017 | 2002 Mercury Sable

2 Answers

Passenger door does not unlock


your going to have to get that panel off with out opening the door.
remove screws ffrom door panel and try to pull up from bottom. put the passenger seat all the way back. be careful and take your time it can be done

Jul 24, 2010 | 1993 Nissan Altima

1 Answer

I need diagram that shows how the door handle works. Someone tried to steal my truck and punched out the lock. Can not get into my truck. HELP


If the rod between the lock and the latch has fallen off, you will have to get in on the other side (can't do that?) Then open the door from the inside and remove the panel (you can remove the passenger side to see how the linkage goes. Then, you can replace the lock (have it set for your key before putting it in)

Jun 23, 2009 | 2000 Chevrolet Silverado

1 Answer

Putting new mirror on passenger side door?


Behind the passenger-side front-door at the bottom of the window
you will find a molded triangular panel with a tweeter [audio speaker].
To access the nuts that affix the side-view mirror to the door you will
remove the panel. Gently pry on the top of the panel to remove it but be careful as speaker wires will be attached. Quick way to replace the mirror assembly is to support the panel and don't put stress on the wires. Open the door and find the nuts that hold the mirror onto the door. If you have electric powered mirrors you will need to separate the connector that sends current to the mirror for the remote function. Remove the nuts and be very careful not to drop the nuts into the door cavity. Good luck!

Jan 10, 2009 | 2003 Oldsmobile Alero

1 Answer

Replacing passenger side miror


need to replace the exterior mirror on the passenger side. How do I remove the mirror from the out side. all the wiring is out Just need advice on how to take of the existing mirrow and replace it with a new one. Does the inside panel need to come off, how many bolts are needed for removal.

Felix.

Dec 29, 2008 | 2007 Chevrolet Tahoe

1 Answer

Mirors and electric windows not working on the drivers door


99% sure if you look in the accordian between the door and frame of the car you'll find cut wires. Pull back the rubber seal and check there first. If they are you'll have to remove the harness and fix it back to the connections in the car for a good repair or order a harness.

Oct 27, 2008 | 1998 Volkswagen Beetle

Not finding what you are looking for?
1998 Ford Windstar Logo

626 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...