Looking for a wiring diagram for a 1992 Toyota Camry - brake lights work, tail lights do not - bulb and fuse are good.

Should all be the same fuze. Check the bulbs and whether the harness to the rear lights that usually runs through the trunk hasn't been pulled.

trace the wires from back of light clusters and make sure the earth is a good connection to the car body/chassis

could be a dirty socket not allowing good contact for the bulb. or you have a bad connection with one of the wires in the back of the socket.

It can be faulty tail light bulb or its issue with tail light control switch or its wiring's are short.

Check the voltage at fuse slot of tail light.Do you receive 12 volt there.If not,then it says tail light switch is not receiving power supply.


---------
There are few help links related to your problem.I suggest you refer the list and check the help links.Click the link below:-----
1994 Toyota Camry: Bypass Tail light Relay Circuit? http://whatisbyme.blogspot.in/2012/04/1994-toyota-camry-bypass-tail-light.html

-----------
2008 Toyota RAV4: Replace Tail light Lens Cover?

http://technoanswers.blogspot.in/2012/04/2008-toyota-rav4-replace-tail-light.html
--------
2003 Chevrolet S10 Tail light Fuse http://schematicsdiagram.blogspot.com/2012/11/2003-chevrolet-s10-tail-light-fuse.html
--------- Chevrolet Parking light and Tail lamp light Wiring diagram http://schematicsdiagram.blogspot.com/2012/11/chevrolet-parking-light-and-tail-lamp.html
---------- Car Tail Lights Not Working?

http://schematicsdiagram.blogspot.com/2011/12/car-tail-lights-not-working.html

----------
Turn Signal Not working http://technoanswers.blogspot.com/2012/11/turn-signal-not-working.html
---------- Right turn signal not working on Pontiac Car?

http://schematicsdiagram.blogspot.com/2011/12/right-turn-signal-not-working-on.html

--------
Only one side indicator light working on car?

http://schematicsdiagram.blogspot.com/2011/12/only-one-side-indicator-light-working.html

-----------
Turn signals not working on 1987 Jeep Wagoneer? http://schematicsdiagram.blogspot.com/2011/12/turn-signals-not-working-on-1987-jeep.html

-----------

SOLVE YOUR 4 WAY FLASHER RELATED PROBLEMS HERE
http://repairhelpcenter.blogspot.com/2012/11/4-way-flasherturn-signal-flashersignal.html

----------
Thesedetails will help.
Thanks.

I have the same problem -

All lights are good - Fuses Good - Brake lights don't go on

Did you fix this problem ? How ?

brown wire is your park LT yellow Left-turn green right-turn. Now the break light my be on it own wire it is red black is ground. but if you have a test light see if the brown wire turns on the test LT when you turn on the park LT or what wire light up when you step on the break pedal. and so on.

Well Jennifer, it sounds like you've done all the things that I'd have done. Try for a bad ground next. Do the lights in the dash cluster work? They're wired together with the tail-lights (so that you know if the rears go out). There should be a ground wire somewhere connecting the body to the engine or chassis.Look around the rear of the engine bay. Good Luck.

YOU MAY NEED A LIGHT FAILURE SENSOR WHICH IS LOCATED IN THE TRUNK ON THE DRIVERS SIDE

You have a ground issue.Current from another circuit is running through the lights to get to ground. this causes them to burn out quickly.You need to do a real detailed visual check.A good component wiring diagram and component locator is a requirement here.

go to http://www.autozone.com/...eId=0900c1528009104f . you may find a wiring diagram there for free.Please vote.