I need the torque settings for a Toyota Corolla 1995 model 4afe engine TORQUE SETTINGS FOR THE CYLINDER HEAD? PLEASE PLEASE HELP

This manual has everything but cam torque

http://www.championbrands.com/aera-torquespecs.pdf

(1) Apply a light coat of engine oil to the threads and under the heads of the cylinder head set bolts.
(2) Using several steps, uniformly install and tighten the 10 cylinder head set bolts and plate washers with a 10 mm bi-hexagon wrench in the order shown in the illustration. Torque:
70 N·m {714 kgf·cm, 52ft·lbf} (c) Mark the front of the cylinder head bolts with paint.

(d) Further tighten the cylinder head bolts 90° as shown in the illustration.
(e) Check that the paint mark is now at a 90° angle to the front. cam bearing caps; Using several steps, uniformly tighten the 10 bearing cap bolts in the sequence shown in the illustration.

Torque:
No. 2 Bearing cap -
30 N·m {301 kgf·cm, 22ft·lbf}
No. 3 Bearing cap -
9.0 N·m {92 kgf·cm, 80in·lbf}

of what the whole car.?
that is in the factory service manual (FSM)
or alldata.com


which engine,? lots of 1.6l MADE BY TOY?
NOT 4AFE (ended in 2001)
state side, we had 3 engine, non are 1.6L
the 1NZ-FE 1.5L
the 1ZZ-FE and 2ZZ-FE both are 1.8L
so what country are you in, ?
find true engine name (under hood,read stickers)
and google for that, I promise you will find it.


9th generation corolla
the e120?
world wide, (not USA) they had
1.6L I4 3NZ-FE
1.6L I4 1ZR-FE
1.6L I4 3ZZ-FE

as you can see 1.6L tells nothing.
only the real name works , getting specs on any engine.
do tell.

Hi Manuel, There are a number of different engines used in the Corolla, knowing which would be a great help. The engines used in the 1993 are of the 'A' series and 'E' series. The torque for the A series is 29 nm + 90 degrees. When removing the head begin loosening from the outer bolts. When the head is off have it inspected for warpage and skimmed if it is required. Tightening any cylinder head always begins at the middle or centre and works outwards. As my friend has said, the camshaft caps are tightened to 9 nm and the inlet manifold goes to 24 nm, and the exhaust is 27 nm. The tappet cover I think is 29 nm. The tappet cover is tightened on the A series with nuts onto the plug tubes. Regards John

petrol engine alloy head 65lbs
main bearing caps 80lbs
big end bolts 40lbs

sounds like you will be better off having another engine installed.

FUEL CONSUMPTION CAUSED BY FAULTY SPARK PLUGS AND IGNITION COILS.FAULTY TRANSMISSION TORQUE CONVERTER NOT LOCKING UP FOR OVER DRIVE.MANUAL TRANSMISSION CLUTCH WORN NOT SLIPPING.STOP UP AIR FILTER.HIGH SPEED DRIVING.LOT OF SHORT STOPS DRIVING IN THE CITY.CHECK FOR LOW TIRE PRESSURE.LOW CYLINDER COMPRESSION.

toyota carina e 1.6i 4afe 16v engine cam tightening torques and sequence pls, thank u

what is the torque specs on 4afe 1.6 toyota corolla connecting rod & cylinder head

hey, torque must be done in 3 steps:
1st 22 ft lbs
2nd 43 ft lbs
final 47 ft lbs
use this sequence of tightening:

9 - 3 -1 -6 -8
7 - 5 - 2 -4 - 10