Just had the dealer replace the WCM on my 06 Ram under warranty(could not turn key without much effort ) but dealer also changed out ignition switch and tumblers and 2 new keys( drove the car to the dealer after using my keys) for $700. If my keys worked; why would I need 2 new smart keys and a switch? Don't they just reprogram the keys to the new WCM? Something's fishy!

You will either need to pay a lock smith to cut a new key or many times it is easier to buy a new set of locks and ignition switch with a key off of ebay and just change everything out.

Hello, to help you alleviate your headache and time consuming catastrophe of disassembling the factory alarm to start your Ram, I believe I can help wrap up the wound a thief has left you with. First off, the immobilizer involved in the ignition and the chip in the key is not a easy task to just "jump". In actuality with less than $200.00 your Ram could be on the road without having to "rig" or "bypass" the factory alarm system. Simple to change out the ignition key switch. Usually comes with programming instructions, ignition switch with immobilizer attached, and new keys to reprogram yourself. Available at any local auto parts stores or dealership. Max time, 1 hour. Simple tools needed. Second option is to go to dealership, with VIN number of your ram, and buy a new key with a chip matching OEM immobilizer and ignition switch. Coat is under $100.00. Only thing about this is you will have to have locksmith cut the key to fit the ignition.
Hope my suggestions will help you alleviate your trouble. Thank you

How to Remove the Ignition Switch Without a Key

1. Turn on your power drill and use your drill bit to make a hold in the key slot of the ignition cylinder. ...
2. Insert a straightened out paperclip into the slot just to the left of the key cylinder. ...
3. Inserting your screwdriver into the cylinder and turn it as far as you can to the right.

How to Remove the Ignition Switch Without a Key - It Still Runs

Videos as well

https://www.google.com/search?safe=off&rlz=1C1QJDB_enCA643CA644&sxsrf=ALeKk029vbM_5jKdSmg0dCur-g8W9nauYw%3A1613687881235&ei=SewuYLLxDeiD_QbL07GwDQ&q=how+to+remove+ignition+lock+cylinder+without+key+dodge

..

Get a key! If you are the owner, the dealer can make you a key if you show title and driver's license and VIN#. You cannot change the ignition switch safely without the key.

CUSTOMER LEARN METHOD
The Customer Learn feature is only available on domestic vehicles, or those vehicles which have a U.S. country code designator. This programming method also requires access to at least two valid Sentry Keys. If two valid Sentry Keys are not available, or if the vehicle does not have a U.S. country code designator, the Secured Access Method MUST be used to program new or additional valid keys to the SKREEM/WCM. The Customer Learn programming method procedures are as follows:

1. Obtain the blank Sentry Key(s) that are to be programmed as valid keys for the vehicle. Cut the blank key(s) to match the ignition switch lock cylinder mechanical key codes.
2. Insert one of the two valid Sentry Keys into the ignition switch and turn the ignition switch to the On position.
3. After the ignition switch has been in the On position for longer than three seconds , but no more than fifteen seconds , cycle the ignition switch back to the Off position. Replace the first valid Sentry Key in the ignition switch lock cylinder with the second valid Sentry Key and turn the ignition switch back to the On position. The second valid Sentry Key must be inserted in the lock cylinder within fifteen seconds of removing the first valid key.
4. About ten seconds after the completion of Step 3, the security indicator in the instrument cluster will start to flash to indicate that the system has entered the Customer Learn programming mode.
5. Within sixty seconds of entering the Customer Learn programming mode, turn the ignition switch to the Off position, replace the valid Sentry Key with a blank Sentry Key transponder, and turn the ignition switch back to the On position.
6. About ten seconds after the completion of Step 5, the security indicator will stop flashing, stay on solid for three seconds , then turn off to indicate that the blank Sentry Key has been successfully programmed. The SKREES/ SKIS will immediately exit the Customer Learn programming mode. After the ignition is cycled the vehicle may be started using the newly programmed valid Sentry Key.

NOTE: The Remote Keyless Entry (RKE) Transmitter will also be programmed during this procedure.

Each of these steps must be repeated and completed in their entirety for each additional Sentry Key that is to be programmed. If the above steps are not completed in the given sequence, or within the allotted time, the SKREEM/ WCM will exit the Customer Learn programming mode and the programming will be unsuccessful. The SKREEM/ WCM will also automatically exit the Customer Learn programming mode if it sees a non-blank Sentry Key transponder when it should see a blank, if it has already programmed eight (8) valid Sentry Keys, or if the ignition switch is turned to the Off position for more than about fifty seconds .

NOTE:

• If an attempt is made to start the vehicle while in the Customer Learn mode (security indicator flashing), the SKREES/SKIS will respond as though the vehicle were being started with an invalid key. In other words, the engine will stall after about two seconds of operation. No faults will be set.
• Once a Sentry Key has been programmed as a valid key to a vehicle, it cannot be programmed as a valid key for use on any other vehicle.

Hello,
This is a common problem apparently. It seems like there is a plastic ring in the ignition switch that breaks off. I am not sure if your car is still under warranty, but here is a link to let you know more about the problem. Chances are your dealer has seen this before. They will have to replace the ignition it appears. I hope for your sake it is under warranty. God bless! Let me know how it goes:
http://www.ford-forums.com/ford-fusion/4432-keys-wont-come-out-ignition.html

Seen this problem before. Here is your solution im the foreman for a jeep dealership.

During cranking/starting, the ignition switch voltage should drop to about 0.4 to 0.5volts and the switch status should show start/crank. If the ignition switch status shows FF, that is an undermined switch status. The ignition switch voltage is supplied by a voltage regulator (5volts) with-in the WCM (WIRELESS CONTROL MODULE). This regulator not only feeds the ignition switch with voltage, but if the vehicle has remote start, it all so powers the WCM antenna. So, items that affect the ignition switch voltage readings would include the power or ground circuits to the WCM, ignition switch and the WCM antenna. The WCM antenna can short and take down the ignition switch voltage. A shorted antenna can cause issues with the WCM functioning properly, i.e. starting and or key programming. Check antenna wire for damage or try and unplug the WCM antenna and recheck the ignition switch voltage.
Take this copy to your dealership and check for radio interference. Good luck with your wrangler got an 08 4 door rubicon I have not had this problem with mine yet. Hope this helps you please rate it.

Hey Tim take a look at this, will this help ?
SUBJECT:
No Engine Crank Or No Engine Start Due To Electronic Lockup Of The WCM / SKREEM
OVERVIEW:
This bulletin involves the replacement of the Wireless Control Module (WCM), and if
equipped, the replacement of the Electric Steering Column Lock (ELV). The WCM is also
referred to as the Sentry Key Remote Entry Module (SKREEM).
MODELS:
2007
SYMPTOM/CONDITION:
The customer will experience a no engine crank AND a no engine start condition. Also, the
remote keyless entry (RKE) system will not operate. This condition may be due to an
electrostatic discharge (ESD) from the ignition key into the Wireless Control Module
(WCM), causing the WCM to electronically lockup. This condition may occur more
frequently in dry and/or cold weather conditions where a sufficient electrostatic charge is
more easily produced. This condition is corrected by the replacement of the WCM
DIAGNOSIS:
1. With the condition present (i.e. the vehicle in the no crank / no start condition), connect
the StarSCAN® scan tool to the vehicle.
2. Turn the ignition switch to the “ON” position, and power up the StarSCAN®.
3. If the WCM is electronically locked up, the StarSCAN® will display the WCM as being
“off bus”.
4. If the no crank / no start condition is present, and the WCM is “off bus”, then reset the
WCM by temporarily removing the IOD fuse (with the key out of the ignition switch),
wait for 10 seconds and then reinstall the IOD fuse.
5. With the IOD fuse reset having been performed, verify that the vehicle will now crank,
start, and run.
6. If the condition is temporarily corrected by performing the above steps, and if the part
number of the WCM is earlier than the part number of the WCM listed in the part
reference table in the Service Bulletin Parts Required Section below, then perform the
Repair Procedure.

car should be under warranty .. try having a new key made .if that dosent fix it. it's in the key lock maybe a wire loose .

If it is an automatic, the transmission shifter is failing,should be covered under powertrain warranty.