Cars & Trucks Logo

Related Topics:

Posted on Feb 18, 2011

Fault codes P1474 P1000 P1111 - XKR Jaguar Cars & Trucks

1 Answer

Carlos Sosa

Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

  • Contributor 1 Answer
  • Posted on Dec 30, 2016
Carlos Sosa
Contributor
Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Joined: Dec 30, 2016
Answers
1
Questions
0
Helped
361
Points
1

2003 jaguar s type r,i recently check engine light came on and i got 8 total codes misfire but im just wondering about the p1474 code which is based on intercooler water pump circuit malfunction and i did a lot of searches and im confused where the intercooler water pump is located ,, so i see one pic of one that is near the radiator and there one near the left driver side block ,,, and theres is one called engine auxiliary water pump so ,, im confused about those which one should i check engine aux or intercooler water pump or are they the same ,,, or different please help i do research before going to mech

3 Related Answers

Anonymous

  • 1 Answer
  • Posted on Apr 22, 2009

SOURCE: failsafe engine mode light comes on, codes

Just a quick mention - for about a month my XK8 low coolant light came on intermittently. This week with no notice while driving normally I got Stability Control Fail and FailSafe Engine Mode and wtih great difficulty got the car back to where I started from (less than a mile). Two days later (when got time) and after a bit of research, I tried it again - same problem and a very unhappy engine. I then disconnected the battery for 15 minutes (probably more) to clear the engine codes as well as check all the wiring and vacuum stuff I could under the hood (at a Jaguar master mechanic's recommendation). No problems found but the car would start and immediately stall with the air intake hose disconnected from the intake butterfly. After I reconnected the air intake hose, she started and purred like normal. The problem is the BATTERY... It is low - I've known it for a LONG time BUT it always started right up and never skipped a beat. I intend to replace it tonight but fully expect that's the issue. I've had the car 6 years (it's a 98) and had NO problems except a dead taillight asembly.

Hope this is of value...

Ad

Anonymous

  • 1 Answer
  • Posted on Feb 18, 2010

SOURCE: fault code p1111+p1647 engin light is on

I have a 2002 X-type Jaguar and the check engine light and cruise control unavailable comes on but the cruise control light goes off once the car warms up. Any ideas?

ZJLimited

ZJ Limited

  • 17989 Answers
  • Posted on Jan 20, 2011

SOURCE: x type fault codes p1111 & p1646 can you shed

P1111 - System Pass
This is flagged after DTCs have been cleared, all engine management OBD diagnostic monitor drive cycles HAVE BEEN COMPLETED.

P1646 - Linear O2 Sensor Control Chip (Bank 1)
Its listed as either a faulty heated HO2 sensor ie lambda sensor (upstream bank 1) or a short (presuming the ECM is OK as no other codes)
Did you replace the right one... bank 1 is at the back of the V6, bank 2 is at the front so its the back one.

Hope this helps (remember to rate tis answer).

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
2answers

My car won't start and is showing a p1000 code . What does this mean?

P1000 is a manufacturer specific fault code:

Ford P1000: OBDII Monitor Testing Not Complete.
Jaguar P1000: Engine control module (ECM) - internal error.
Kia P1000: System diagnosis incomplete.
Land Rover P1000: Engine control module (ECM) memory erased - no codes stored.
Mazda P1000: OBDII Drive Cycle Malfunction.

So depending on the manufacturer of your car would depend on the meaning of a P1000 code!
0helpful
1answer

2004 xj vanden plas. Check engine light came on. Obd read as p0193 and p1111. Need help. Ty

p0193 sounds like a ip sensor circuit malfunction the p1111 is system check has been completed p1000 system check is not completed..that number will check from 1000 to 1111 when the car has ran a complete self check of itself.
0helpful
1answer

2003 jaguar s type code p1000 and c1165

the p1000 is a system readiness code meaning the car is checking itself..it means its not finished etc but once it has the code will change to p1111..meaning system check completed, the c1165 is a abs or wheel speed code, check the wheel where this code is originating
0helpful
1answer

Radio code

OBD system tests
Possible fault codes:
P1000 OBD system tests Operation not
completed
Setting of the fault code P1000 has no
influence on the system <Engine
management>, smooth running or performance
as long as it is automatically erased
whilst driving.
The fault code P1000 indicates noncompletion
of system tests.
* Misfire detection
* Evaporative emission control system
* Exhaust-gas recirculation
* Lambda sensor
* Exhaust gas catalytic converter
The fault code P1000 cannot be erased. It
is cancelled automatically once the
vehicle has completed certain driving
cycles.
Jul 27, 2013 • 2007 Ford F
3helpful
1answer

P1111 Code

The P1111 unlike the P1000- the P1111 means the ECM has completed a drive cycle with no faults stored. The P1000 means the ECM has not yet completed the drive cycle. They are basicly drive cycle readiness codes doing a system check...this is a natural code..not to worry its checking the car all over between drive cycles for any malfunctions..
sorry i missed u online but the code is nothing to worry about...
0helpful
1answer

P1111 code

The P1111 unlike the P1000- the P1111 means the ECM has completed a drive cycle with no faults stored. The P1000 means the ECM has not yet completed the drive cycle. They are basicly drive cycle readiness codes doing a system check...this is a natural code..not to worry its checking the car all over between drive cycles for any malfunctions..
7helpful
3answers

What does code P1111 mean

Hi.

P1111 is not a fault code. It is a special designator Jaguar uses meaning system ready, drive cycles completed after the last fault event.
4helpful
1answer

What does the service code p1111 mean?

Copied directly from a Jaguar forum:

P1111 is not a fault code. It is a special designator Jaguar uses meaning system ready, drive cycles completed after the last fault event. P1000, on the other hand, means system not ready, or drive cycles not completed after the last recorded fault event.

Some OBD II Basics - All P0xxx codes are generic and uniform across all manufacturers and mean the same on every car. All P1xxx codes are manufacturer specific codes. You cannot use a generic code chart to analyze P1xxx codes for a Jaguar.

Next time your car displays an engine fault light, try reading the codes then. If you have a CEL illuminated and the only code read is P1000 or P1111, then you probably have a fault that generic code readers cannot see. Could be a chassis code, for example.

One last thing - Neither P1000, nor P1111 can be erased.

Hope this helps you.
0helpful
1answer

I HAVE A JAG X-TYPE WITH THE CODE P1000 NEED A FULL DEFINITION

P1000 OBD (On Board Diagnostic) Systems Readiness Test Not Complete.. Retest the vehicle and if there is something wrong with it, you will get another code. If the system is good then you will receive P1111 System Pass.
3helpful
2answers

Fault code P1000 [18,2,10,0],Ford Fiesta 2005

P1000 means that you or someone has disconnected the battery,and the car has not been driven far / long enough for the computer to relearn its stratagies.
Engine light could be the fault of the speed sensor, or wiring to the sensor.
Jul 13, 2009 • 2007 Ford F
Not finding what you are looking for?

371 views

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...