Replace wiper motor - 2001 Oldsmobile Intrigue

The part that is attached to the wiper motor is in the wrong location. Remove the nut or bolt that attached the wiper transmission to the motor and remove the short arm from the wiper motor. Turn the wiper motor on and then off. wait until it stops moving. Set the wiper arms to the correct "home" position. Reattach the wiper transmission arm to the wiper motor.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

video
http://www.bing.com/videos/search?q=2006+Buick+Rendezvous+Open+Question+Wiper+motor+replacement&FORM=HDRSC3


2006 Buick Rendezvous Open Question Wiper motor replacement Bing Videos

Windshield wiper motors are generally easy to replace. You need to remove the windshield wipers and take off the small grill panel above the hood and under the windshield. You should see the motor in there. It simply unbolts and unplug the electrical connector and replace it with a new one.

REMOVAL

1. Raise and support the hood.
2. Remove the windshield wiper pivot arms.
3. Remove the cowl top vent panels.

1. Disconnect the windshield wiper mounting arm and pivot shaft.

1. Remove the access cover from the dash panel.
2. Remove the mounting arm and pivot shaft retaining clip.
3. Disconnect the windshield wiper mounting arm and pivot shaft from the windshield wiper motor.

1. Remove the windshield wiper motor.

1. Disconnect the electrical connector.
2. Remove the three bolts.
3. Remove the windshield wiper motor.

INSTALLATION

1. Install the mounting arm and pivot shaft retaining clip on the windshield wiper mounting arm and pivot shaft.

1. Install the windshield wiper motor.

1. Place the windshield wiper motor in the dash panel.
2. Install the three retaining bolts.
3. Reconnect the electrical connector.

1. Reconnect the windshield wiper mounting arm and pivot shaft.

1. Press on the windshield wiper mounting arm and pivot shaft after it is aligned with the windshield wiper motor.
2. Install the access cover in the dash panel.

1. Install the cowl top vent panels.
2. Install the windshield wiper pivot arms.
3. Adjust the windshield wiper pivot arms.

This is technically for the V6 4.2L but I'm sure those Ford E250's have the same setup for windshield wiper motor. Let me know how it goes.

Intermittent wipers: Inside the wiper motor (of most cars) there is a diode or diodes. They burn out or they break. If you replace the diodes the intermittent wipers will work again. If you cannot replace the diodes, replace the wiper motor completely (used or new)

Tur the wipers on and tap the wiper motor. If it start to work replace it.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Hi.

Check if there is power to the wiper module when you turn on the wipers. If there is no power to the wiper module check multifunction switch, wiring and fuse. If there is power getting to the wiper module but the wiper motor is not energized, replace the wiper module. If the wiper module is energizing the motor but the motor does not start, replace the wiper motor. The wiper module is located in front of the wiper motor, under the hood. The module is held by screws, connected to the motor, and protected by a cover.

Regards.

Ginko

Here are a few other things to check beside the fuse and relay:

Check Wiper Motor - the wiper motor is the driving force of the windshield wiper. Feel the motor and listen to a humming sound. If there is no humming, the motor is the problem. Check if the motor is working properly and see to it that its electrical connections are made properly. If you find that the motor is dead and beyond repair, get it replaced immediately.

Check For Break in Connecting Wires - the connecting wires of the motor sometimes go loose and that may cause the windshield wipers to stop working. Also check the battery plug connection which the motor has. Connecting the loose wires properly or fixing/replacing the plug might solve your problem.

Check Wiper Switch - another wiper assembly part that can malfunction is the wiper switch itself. Check for switch malfunction and if you find that is indeed the problem, get it replaced from a mechanic.

Check for Bent Wiper Arms - bent wiper arms can cause the operation of the wipers to be hampered. If the wiper arms are bent beyond repair, get them replaced immediately.

This is what I Found there was not any Illustration's with it looks Fairly simple, Good luck



FRONT

1. Disconnect linkage assembly from wiper motor shaft.
2. Disconnect electrical connectors from wiper motor.
3. Remove wiper motor attaching bolts, then wiper motor.

REAR

1. Remove wiper blade and arm assembly.
2. Remove access panel on back door.
3. Disconnect linkage assembly from wiper motor shaft.
4. Disconnect electrical connectors from wiper motor.
5. Remove wiper motor attaching bolts, then wiper motor.

Skill
Level Mfg.
Warranty Standard Wiper Motor Labor Replace Front B 0.7 1.0
PLEASE DONT FORGET TO RATE ME Thank You Much

check for power at the wiper motor. If power at the wiper motor but no wiper action then replace the motor. if no power at the motor then use a jumper wire and put power to the motor. Does motor run? if so check for open circuit in the wire someplace.