Crankshaft poistion sensor location for 2005 nissan altima

Yes there are

2 Recallsfor 2005 NISSAN ALTIMA

• Summary. ON CERTAIN PASSENGER VEHICLES EQUIPPED WITH A 2.5L ENGINE, THE CRANKSHAFT POSITION SENSOR CAN OVERHEAT CAUSING A BRIEF INTERRUPTION IN THE SIGNAL OUTPUT FROM THE SENSOR.
• Remedy. DEALERS WILL REPROGRAM THE ECM FREE OF CHARGE. ...
• Notes.

2005 NISSAN ALTIMA 4 DR ' NHTSA

2005 Nissan Altima Recalls ' Cars.com

www.cars.com > research > nissan-altima-2005 > recalls

CERTAIN TYC HALOGEN TYPE HEADLAMP ASSEMBLIES P/N 20-6644-00 SOLD AS AFTERMARKET EQUIPMENT FOR 2005-2006 NISSAN ALTIMA ...

2005 Nissan Altima Safety Recalls - Autoblog

www.autoblog.com > ... > Altima > 2005 Nissan Altima

SUMMARY. ON CERTAIN PASSENGER VEHICLES EQUIPPED WITH A 2.5L ENGINE, THE CRANKSHAFT POSITION SENSOR CAN OVERHEAT CAUSING A ...

2005 Nissan Altima Recalls ' RepairPal

repairpal.com > 2005-nissan-altima > recalls

Sep. 22, 2020 - Most Recent 2005 Nissan Altima Recall On certain passenger vehicles equipped with a 2.5l engine, the crankshaft position sensor can overheat causing a brief interruption in the signal output from the sensor. 2005 Nissan Altima Reviews and Owner Comments - RepairPal
Oct. 15, 2020
2006 Nissan Altima Recalls ' RepairPal
Sep. 24, 2020
2004 Nissan Altima Recalls ' RepairPal
Sep. 23, 2020
Nissan Recall 07V527000: Overheating of Crankshaft Position ...
Dec. 31, 2007
More results from repairpal.com

2005 Nissan Altima Recalls & Safety Notices ' Kelley Blue Book

www.kbb.com > nissan > altima > 2005 > recall

Almost 350,000 Nissan Altima vehicles made between 2015-2017 were recalled dealing with an improper rear door latch. Lowering a rear window could ...

yes you have to drop tank to replace fuel pump and filter as it is one unit pretty easy though.

crankshaft sensor is either under the harmonic balancer pully or bolted to block facing it you normally have to pull pully to change sensor but some you dont you will need a puller and a installer if you have to pull the pully

relay should be under the hood in relay area

if this was helpful please give me a good rating

Here's some pics of my 2003 Altima Crankshaft Sensor. Often mistaken by the Camshaft Sensor because both are identical sensors. They are each located in different locations. I've seen diagrams with the WRONG labeling. Again, this is so confusing for even a mechanic to understand because both sensors carry the same part number which is rare. http://x.nissanhelp.com/forums/members/digitaldxing-albums-2003-nissan-altima-crankshaft-position-sensor-picture331-2003-nissan-altima-crankshaft-position-sensor.html

It is located just under the starter and should be a 3 wire connector going into the bell housing. Let me know if you need a pic. You can email me at [email protected]

it is on the driver45s side rear of engine, go to the link for a picture.
http://www.paulstravelpictures.com/Nissan-Altima-Camshaft-Crankshaft-Sensors/

You are incorrect sir. There is a very good Youtube video showing you exactly where it is that is how I changed mine. The Crankshaft is located behind the engine block below and around from the cam sensor which is easly spotted looking at the engine. The crankshaft is in a difficult spot but once you figure out where it is it's easy...ish hope this helps

hi the speed control location is situated on each wheel with the abs unit on a trans axle its on the drivers side near to yhe top of the transmission please rate this answer hope this helps

The crankshaft position sensor is on the right rear of cylinder block, below starter motor.

CPS - Crankshaft Position Sensor; common problem.

The oil filter is located behind the right (passenger) inner fender cover. It is right next to the crankshaft pulley at the bottom of the front of the engine facing toward the right front wheel. I do not have a picture at this time.

Hope this is helpful!


Nissan Scope Technician- 10+ years experience in Nissan dealership.