Rear brake Squeal-problem began after brake pad replacement

Sounds like a dragging brake pad. There is an adhesive that can be applied between the calipers and the pads. Or it may be time for a rear end brake change.

I find it hard to believe that a brake squeal is normal. Here is what I would recommend doing and there may be some reluctance from the dealership to perform this operation while under warranty. As a mechanic when I am being told that the brakes squeal I typically procede by removing the brake pads and scuffing the surface of the pads as well as the rotors. This typically removes the squeal noise. They do make coatings that can help reduce brake squeal but typically whenever the coating is removed the squeal reurns. I would ask the dealership for a copy of this TSB that they are talking about and review it yourself to make sure that is exactly what is happening. If you are not happy with the brakes or the dealers response then I would advise you to get the customer service toll free number from your owners manual and tell them how un happy you are with this descision and I am willing to bet you will get different results. I would suggest that you get some ceramic pads installed to eliminate the noise and if you are demanding enough they would probably be willing to pick up the check but remember you are going to have to be very demanding.

Brake Pads Removal & Installation Front

To Remove:

1. Drain brake fluid to ½ full level in reservoir.
2. Remove the front wheels.
   
   
3. Remove the front brake caliper assembly.
4. Remove the 2 anti-squeal shims from each of the 2 brake pads.
5. Remove the wear indicator from each of the 2 brake pads.

To Install:
NOTE: When replacing worn pads, the anti-squeal shims must be replaced together with the pads.

1. Using a large C clamp or equivalent press piston into the caliper.
2. Apply disc brake grease to the inside of each anti-squeal shim.
3. Install the anti-squeal shims on each pad.
4. Install the pad wear indicator clip to the pads.
5. Install the pads with the pad wear indicator plate facing upward.
6. Install the brake caliper with the 2 mounting bolts. Torque the bolts 25 ft-lb (34 Nm).
7. Install the front wheels.
8. Fill the master cylinder with new clean brake fluid.
9. Pump the brake pedal several times to seat the brake pads.

Rear TMC made rear brake components

TMMK made rear brake components

To Remove:

1. Drain the brake fluid to ½ full level in reservoir.
2. Remove the rear wheels.
3. Remove the caliper slide pins.
4. Remove the caliper slide pin bushings (TMMK made) (Kentucky).
5. Remove the rear brake calipers.
6. Remove the 2 brake pads with the anti-squeal shims.
7. Remove the anti-squeal shims and pad wear indicators from brake pads.

To Install:

1. Using a large C clamp or equivalent press the piston into the caliper.
2. Coat both sides of the outer anti-squeal shim with pad grease.
3. Install anti-squeal shims to each pad.
4. Install wear indicators on the 2 brake pads.
5. Install the caliper slide pin bushings (TMMK made) (Kentucky).
6. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
   • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
   • TMMK made (Kentucky): Torque the caliper slide pin 34 ft-lb (47 Nm)
7. Fill the master cylinder with new clean brake fluid.
8. Pump the brake pedal several times to seat the brake pads.
9. Install the rear wheels.

Brake Rotor Removal & Installation Front To Remove:

1. Remove the front wheels.
2. Remove the front brake caliper assembly.
3. Remove the front brake pads.
4. Remove the 2 bolts and caliper mounting bracket.
5. Place match marks on the disc and axle hub.
6. Remove the front wheel disc.

To Install:

1. Align the match marks and install the front disc.
2. Install the brake caliper mounting bracket. Torque the bolts 79 ft-lb (107 Nm).
3. Install the brake caliper. Torque the bolts 25 ft-lb (34 Nm).
4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
5. Fill the reservoir with brake fluid.
6. Bleed the brake system.
7. Install the front wheel.

Rear To Remove:

1. Remove the rear wheels.
2. Remove the brake caliper assembly.
3. Remove the brake pads.
4. Remove the 2 bolts and the caliper mounting bracket.
5. Place match marks on the disc and axle hub.
6. Remove the rear disc.

To Install:

1. Align the match marks and install the rear disc.
2. Install the rear brake caliper mounting bracket. Torque the bracket bolts as follows:
   • TMC made (Japan): Torque the bracket bolt 46 ft-lb (61.8 Nm)
   • TMMK made (Kentucky): Torque the bracket bolt 34 ft-lb (47 Nm)
3. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
   • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
   • TMMK made (Kentucky): Torque the caliper slide pin 32 ft-lb (43 Nm)
4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
5. Fill the reservoir with brake fluid.
6. Bleed the brake system.
7. Install the rear wheel

Brake Pads
Removal & Installation
Front





3.4L front disc brake assembly









4.0L and 4.7L front disc brake assembly




To Remove:

1. Before servicing the vehicle, refer to the precautions in the beginning of
   this section.
   
2. Remove or disconnect the following:
   
   
   
   • Front wheel
     
   • Clip, 2 caliper pins, the anti-rattle spring then remove the 2 brake pads
     and the 4 anti-squeal shims

To Install:

CAUTION
Only replace brake pads on 1 side of the
vehicle at a time. Failure to use this procedure could cause the caliper pistons
on the opposite side of the vehicle to pop out requiring the reconditioning or
replacement of the brake caliper.

1. Remove a small amount of brake fluid from the master cylinder.
   
2. Install a used brake pad into the caliper and compress the caliper pistons.
   
3. Apply disc brake grease to both sides of the inner anti-squeal shims.
   
4. Install or connect the following:
   
   
   
   • Anti-squeal shims to the new brake pads
     NOTE: When replacing worn pads, the anti-squeal shims must be replaced
     together with the pads.
     
     
   • 2 brake pads
     
   • Anti-rattle spring and the 2 caliper pins
     
   • Clip
     
   • Front wheel
   
   
5. Depress the brake pedal several times to seat the brake pads.
   
6. Check the brake fluid level and top off as needed.

Rear
To Remove:

1. Before servicing the vehicle, refer to the precautions in the beginning of
   this section.
   
2. Remove or disconnect the following:
   
   
   
   • Rear wheel
     
     
     
     
     
     
     
     
     
     
     
   • 2 cylinder slide pins from rear caliper assembly
     
   • Caliper assembly from rear caliper mounting
     
   • 2 brake pads with anti-squeal shims from rear caliper mounting
     
   • 2 anti-squeal shims from each disc brake pads
     
   • Pad wear indicator plate from the inner side disc brake pad
     
   • 4 pad support plates from the rear caliper mounting

To Install:

1. Install or connect the following:
   
   
   
   • 4 pad support plates on the rear caliper mounting
     
   • Pad wear indicator plate on the inside brake pad
     Note: Install the pad wear indicator facing downward.
     
     
   • Anti-squeal shims on each brake pad
     
   • 2 disc brake pads with anti-squeal shims to the caliper assembly
   
   
2. Apply lithium soap base glycol grease to the sliding part of 2 caliper slide
   pins.
   
3. Install or connect the following:
   
   
   
   • Disc brake caliper assembly with 2 caliper slide pins
     
   • Torque to 65 ft-lbs (88 Nm)
     
   • Rear wheel
   
   
4. Depress the brake pedal several times to seat the brake pads.
   
5. Check the brake fluid level and top off as needed.

--- Removal & Installation
Front
To Remove:

1. Before servicing the vehicle, refer to the precautions in the beginning of
   this section.
   
2. Remove or disconnect the following:
   
   
   
   • Front wheel
     
   • Front brake caliper assembly
   
   
3. Make matchmarks on the disc and the axle hub.
   
4. Remove the front disc.

To Install:

1. Align matchmarks and disc onto axle hub.
   
2. Install or connect the following:
   
   
   
   • Front brake caliper assembly with the 2 bolts
     
     
     
     1. Torque to 90 ft-lbs (123 Nm)
     
     
   • Front wheel

Brake Pads Removal & Installation Front To Remove:

1. Remove the front wheels. Front brake caliper (exploded view)
   
   
2. Loosen the caliper bleeder.
3. Hold the slide pin; remove the 2 mounting bolts and remove the brake caliper from the support.
4. Support the caliper.
5. Open the brake bleeder. Press the caliper piston into the bore.
6. Close the bleeder after the piston has reached the bottom of the caliper bore.
7. Remove the brake pads, support plates, wear indicators and anti squeal shims.
8. Remove the slide pins and bushings from the caliper support.

To Install:

1. Lubricate the slide pins and bushings with brake grease.
2. Install the bushing on the slide pin.
3. Install the slide pin on the caliper support.
4. Install the brake pad support plates on the caliper supports.
5. Lubricate the anti squeal shims with brake grease.
6. Install the anti squeal shims on the brake pads.
7. Install the pad wear indicator facing upward and install the pads on the caliper support.
8. Install the caliper on the support.
9. Install the 2 mounting bolts, hold the slide pins and tighten 25 ft-lb (34 Nm).
10. Fill the reservoir and bleed the brakes.
11. Install the front wheels.

Rear To Remove:

1. Remove the rear wheels.
2. Loosen the caliper bleeder. Rear brake caliper (exploded view)
   
   
3. Hold the slide pin; remove the 2 mounting bolts and rear brake caliper assembly from the support.
4. Support the caliper.
5. Open the brake bleeder. Press the caliper piston into the bore.
6. Close the bleeder after the piston has reached the bottom of the caliper bore.
7. Remove the brake pads, support plates, and anti squeal shims.
8. Remove the slide pins from the caliper support.

To Install:

1. Lubricate the slide pins with brake grease.
2. Install the slide pin on the caliper support.
3. Install the brake pad support plates on the caliper supports.
4. Lubricate the anti squeal shims with brake grease.
5. Install the anti squeal shims on the brake pads.
6. Install the rear pads on the caliper support.
7. Install the rear caliper on the support.
8. Install the 2 mounting bolts, hold the slide pins and tighten 25 ft-lb (34 Nm).
9. Fill the reservoir and bleed the brakes.
10. Install the front wheels.

You, Probably will, Brake Squeal is NOT a new problem.
Disc brake's have been Squealing since, They, became
factory installed on chevrolet in 1971. Before, that they,
were a option. In 72 they even had a bulleton how, to
FIX it. And, no it didn't work.
With That said, Any time you replace Brake pads you,
should always re-surface the Rotors.
Why? First you may start to notice a pulsation as the
pads ware (sometimes! ) The best way to avoid, brake
squeal is to manchine the Rotors put, the blue membrain
sealent on the back side of the pads. And hope that works!!
Some brakes Pads squeal JUST SQUEAL??
You, Could do the same Brake job the same as you did
this one and, they may NOT Squeal.WHY, I WISH I NEW. They
sell all types of STUFF to stop Brake noice DON'T waste your $$.

you need to grease the metal clips at the top and bottom of the pads (dont get grease on the rotor or pad though) and also spray some "disc brake quiet" on the back of the pads. it comes in a red can and the spray that comes out is like sticky red paint. do those 2 things and the squeals will be gone.

Pads will reproduce sound just like a needle on a phonograph. Hard linings will accentuate this. Have the rotors re-surfaced and finished with a non-directional pattern(I make a quick pass with a D/A sander over surfaces while still on the lathe) Generally this will help.

change to a ceramic pad not semi metallic

Did you buy factory pads or get cheap aftermarket pads? If aftermarket did you get the ceramic? The cheap aftermarket ones tend to squeal pretty bad. Like the last comment on here, you should have your rotors turned whenever you change the pads.