Need to know how to time my car

SOURCE: ineed a 93 suzuki sidekick timing belt diagram

My sincere apologies for the delayed response.
I am personally going back to answer your unanswered questions.

I do not know if you still need this information, but I am going My sincere apologies for the delayed response.
I am personally going back to answer your unanswered questions.

I do not know if you still need this information, but I am going ahead and answering it anyway. You may want to Print the Diagrams for future use.

CLICK on the following LINK. It has the Belt Diagrams you will need.
If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Again my apologies...ahead and answering it anyway. You may want to Print the Diagrams for future use.

CLICK on the following LINK. It has the Belt Diagrams you will need.
If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Again my apologies...
http://www.2carpros.com/car_repair_information/year/1993/make/suzuki/model/sidekick/1993_suzuki_sidekick_timing_belt_diagram_marks.htm

SOURCE: Timing Belt Replacement+Diagram

This should help you http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528008daae

SOURCE: need timing belt mark diagram for 95 corolla 4afe

malibluert: YOUR IN LUCK! This series engine is simple and the references aren't hard to find. READY???????
IF you are just trying to reset the belt at the top and have not remover the crank pulley, bring the crank around to Top dead center on the # 1 cylinder,. It will read Zero degrees on the timing mark scale.
Up top, look at the cam gear closely You will see that there are 5 spokes which support the actual gear. Look closer and you will see that one of these spokes has a small hole in it about 3/4th of the way towards the outside of the gear. Position the gear to where that hole is at 12:00 PM. NOW, if you look thorough the hole, you should should see a small notch that the hole should be centered on. If not, move the gear until you can look through the hole and the notch falls dead center. At that point in time, you have the crank ant camshaft in perfect time with each other.
When you put the belt on, make sure that the side which is slack is the tensioner side. You should be able to slip the belt on, matching the teeth with the teeth on the gears to where one side is fairly tight and you can not roll the cam counter clockwise.
IF you are replacing the belt, you have the crank pulley off and you position the woodruff key straight up at 12:00 PM and the procedures are all the same other than that. when you set the tension. A good rule of thumb is to find the longest span of belt, and with your thumb and forefinger twist the belt. if it twists to 45 degrees toward the block, it's perfect. Any more or less, needs to be reset.
I hope my answer suffices. A picture wouldn't be any more clear.
Let me know how you did.
NOTE: This engine does NOT bend valves when a timing belt fails.

SOURCE: timing belt broke on 1998 kia sportage, need the correct points

Hi, Just to clarify and clear things up, the motor used in the 1998 to 2002 Kia Sportage is actually the Mazda FE3 engine and it is a NON-INTERFERENCE engine.

For any an all repair information on any Kia vehicle produced you can access the KGIS system (Kia Global Information System), just go to www.kiatechinfo.com and create and account (its completely FREE). After you do this you will have access to all the Kia Shop Manuals, DTC Manuals, Recall information for your vehicle and more.

I just had the same problem with my Sportage and found all the information that I needed through KGIS. Hope this helps and good luck on fixing your Sportage.

SOURCE: need diagram for timing belt for 1991 mazda

here you go buddy

http://forums.mazdaworld.org/index.php?showtopic=25269

http://www.2carpros.com/forum/1994-mazda-protege-replacing-a-blown-head-gasket-vt206242.html

http://www.2carpros.com/forum/2000-mazda-protege--my-timing-belt-broke-again,-oil-pressure-vt253721.html

http://www.blurtit.com/q298393.html

hope this helps.

thanks,

voodoo