Power Steering Pressure Hose

How to Remove a Power Steering Hose the Easy way, Tool ...

? 7:49
www.youtube.com/watch?v=OVBFrMcmV7Y
Dec 12, 2013 - Uploaded by Artistry Photography How to Remove a Power Steering Hose the Easy way, Tool Review ... The removal of this power steering pressure hose is a hard job but the ...

Replacing A Leaking Power Steering Hose - YouTube

? 2:38
www.youtube.com/watch?v=l1boEHtawcM
May 12, 2010 - Uploaded by Scotty Kilmer replace the whole hose assembly, they hold 1600 psi pressure, you can't .... i was told i need a new power steering pressure hose for my 2003 .

Wild guess, there is an internal power steering pump pressure relief valve that is stuck or not operating properly and the pressure is going way above the rated capacity of the hose. May need a new power steering pump. Who is changing your hose? Some chance the hose is not rated for the pressures being developed by the pump.

If you notice problem with power steering,the hose has to be inspected,if its faulty it has to be replaced.

=========
For your help,i provide you with few solved helplinks showing how exactly to replace power steering hose:------

How to Remove Power steering Pressure Hose ?

http://schematicsdiagram.blogspot.com/2011/12/how-to-remove-power-steering-pressure.html

---------

How to replace power steering pressure hose?

http://technoanswers.blogspot.in/2012/02/how-to-replace-power-steering-pressure.html

--------------
These will help.
Thanks.

Duplicate question.

RETURN TURN LINE GOES TO THE LEFT OF RACK PINION AND HIGH PRESSURE HOSE GOES TO THE RIGHT OF RACK PINION.LOOKING AT POWER STEERING PUMP HIGH PRESSURE HOSE THICK HOSE SCREWS INTO POWER STEERING PUMP.WHILE LOW PRESSURE HOSE HAS A HOSE WITH A CLAMP THE LOW PRESSURE HOSE HOOKS TO TOP OF POWER STEERING PUMP.LOW PRESSURE DONT SCREW INTO POWER STEERING PUMP IT IS HELD IN PLACE BY A HOSE SMALL CLAMP.

Hopfully this will be ALL you need Besides Pulley REMOVAL TOOL It can be Rented @ AutoZONE

REMOVAL

1. Remove drive belt.
2. Raise vehicle on hoist. WARNING: TURN AIR SUSPENSION SWITCH (LOCATED IN LUGGAGE COMPARTMENT) OFF TO PREVENT VEHICLE DAMAGE OR PERSONAL INJURY.
3. Remove power steering pressure hose bracket.
4. Disconnect electrical connector at power steering control valve actuator.
   1. Install Steering Pump Pulley Remover T69L-10300-B on the pulley hub. CAUTION: Do not apply in-and-out pressure on the power steering pump shaft. Pressure will damage the internal thrust areas.
   2. Hold the small hex-head and rotate the tool nut counterclockwise to remove the power steering pump pulley.
   3. Disconnect power steering pressure hose at power steering pump and drain fluid into a container.
   4. Disconnect power steering return hose at power steering pump and drain fluid into a container.
   5. Remove four retaining bolts and power steering pump and power steering pump pulley assembly.
   6. Remove power steering pressure switch from pump.
   INSTALLATION
   
   1. Position the power steering pump on the mounting bosses of engine block and install the bolts at the side of the power steering pump. Tighten to 20-30 Nm (15-22 ft. lbs.).
   2. Connect the power steering reservoir pump hose to the power steering pump and reposition the hose clamp to power steering pump inlet fitting.
   3. Replace power steering pressure hose O-ring.
   4. Install the power steering pressure hose to the power steering pump fitting. Tighten the tube nut with a tube nut wrench rather than with an open-end wrench. Tighten to 34-46 Nm (26-33 ft. lbs.). NOTE: Swivel or end play of the power steering pressure hose end is normal and does not indicate a loose fitting.
   5. Place the power steering pump pulley on the power steering pump shaft and install Power Steering Pump Pulley Replacer T91P-3A733-A. The small diameter threads on the tool should be engaged in the power steering pump shaft. CAUTION: Do not apply in and out pressure on the shaft. Pressure will damage the internal rotating group.
   6. Hold the small hex-head and rotate the tool nut clockwise to install the power steering pump pulley on the shaft. CAUTION: Do not apply in and out pressure on the shaft. Pressure will damage the internal rotating group. NOTE: The power steering pump pulley face must be flush within 0.25 mm (0.010 inch) of the end of the pump shaft.
   7. Remove the Power Steering Pump Pulley Replacer T91P-3A733-A.
   8. Remove the shipping tube nut from power steering pump housing prior to installation.
   9. Connect electrical connector to power steering control valve actuator.
   1. Install power steering pressure hose bracket.
   1. Lower the vehicle.
   2. If equipped, turn the air suspension ON.
   3. Install drive belt on the power steering pump pulley.
   4. Fill the power steering pump reservoir with Power Steering Fluid Motorcraft MERCON(r) ATF.

If it just the Pressure Hose which has metal at the ends of a rubber hose than you should be able to just change the hose. Link for that would be here:
http://shop.advanceautoparts.com/webapp/wcs/stores/servlet/product_Power-Steering-Pressure-Hose-Powercraft_18071027-P_18_R%7CGRP60016_636201111___

now there is also a return hose, which is here:
http://shop.advanceautoparts.com/webapp/wcs/stores/servlet/product_Power-Steering-Return-Hose-Powercraft_15990006-P_19_R%7CGRP60016_277020352___

Basically yeah, you can just change out the hoses. Hope I helped.

Power Steering Line/Hose: Service and Repair
Pressure Hose
Power Steering Pressure Pipe/Hose Replacement (3.8L)
Removal Procedure
1. Place a drain pan under the vehicle.
2. Remove the accessory drive belt.
3. Raise and support the vehicle. Refer to Vehicle Lifting.
4. Remove the tire and wheel assembly.
5. The power steering pressure hose is the lower hose at the power steering gear.
Remove the power steering pressure hose from the power steering gear.
6. Remove the power steering pressure hose from the power steering pump.
7. Remove the power steering pressure hose from the clamps on the power steering gear.
8. Remove the power steering pressure hose from the vehicle.
Installation Procedure
1. Install the power steering pressure hose to the vehicle.
2. Install the power steering pressure hose to the clamps on the power steering gear.
Notice: Refer to Fastener Notice in Service Precautions.
3. Install the power steering pressure hose to the power steering pump.
^ Tighten the fitting to 27 Nm (20 ft. lbs.).
4. Install the power steering pressure hose to the power steering gear.
^ Tighten the pressure hose fitting to 27 Nm (20 ft. lbs.).
5. Install the tire and wheel assembly.
6. Remove the drain pan from under the vehicle.
7. Lower the vehicle.
8. Install the accessory drive belt.
9. Fill the power steering system with power steering fluid.
10. Bleed the power steering system.
11. Inspect the power steering system for leaks.

i pERSONALY WOULD REPLACE IT MYSELF EVEN WITHOUT MY 30yrs Of Experience in this Field. I have Enclosed Instructions for you to use. PLEASE dont Forget to RATE me As MOST folks DONT remember to that is how WE Get our Ratings such as GURU THANK YOU and Good Luck On The Job, Dont PAY a dime If YOU CAN > D I Y

REMOVAL PROCEDURE

1. Remove the power steering pressure hose (2) from the power steering pump (1).
2. Raise the vehicle on a hoist. Refer to Vehicle Lifting.
3. Remove the front exhaust pipe, automatic transmission only. Refer to Intermediate Pipe Replacement in Exhaust System
4. Remove the power steering pressure hose (1) from the power steering gear (3).
5. Remove the power steering hose retainer (2).
6. Remove the power steering pressure hose (1) from the vehicle
   1. Install the power steering pressure hose (1) to the vehicle
   2. Install the power steering hose retainers (2). NOTICE: Refer to Fastener Notice in Service Precautions.
   3. Install the power steering pressure hose (1) to the power steering gear (3). Tighten the fitting to 27 Nm (20 ft. lbs.).
   4. Install the front exhaust pipe, if removed. Refer to Intermediate Pipe Replacement in Exhaust System.
   5. Lower the vehicle.
      1. Install the power steering pressure hose (2) to the power steering pump (1). Tighten the fitting to 27 Nm (20 ft. lbs.).
      2. Bleed the power steering system. Refer to Bleeding Power Steering System in Service and Repair of Steering.

Here is a pic.

[IMG]http://i253.photobucket.com/albums/hh43/chuck943/DG1690A.gif[/IMG]



1 3A674 Power Steering Pump 2 3A714 Power Steering Pressure Hose 3 3C510 Power Steering Hose Bracket 4 3N824 Power Steering Pressure Switch 5 3504 Steering Gear 6 3A713 Power Steering Return Hose (Gear to Cooler) 7 3D746 Power Steering Fluid Cooler 8 3493 Power Steering Return Hose (Cooler to Pump