Best way to remove blower motor - 1993 Chevrolet Lumina

The blower resistor in a Toyota Townace Noah with a 3S engine is typically located near the blower motor, which is responsible for directing air into the vehicle's cabin.
Here is a general guide on how to locate the blower resistor in a Toyota Townace Noah with a 3S engine:

1. Locate the blower motor: The blower motor is typically located under the passenger side dashboard, near the footwell.
2. Identify the blower resistor: The blower resistor is typically a small rectangular or cylindrical component that is connected to the wiring harness near the blower motor.
3. Remove the blower resistor: To access the blower resistor, you may need to remove the cover or the panel that covers the blower motor. You can then unplug the wiring harness and remove the mounting bolts to remove the blower resistor.

Note: The location and accessibility of the blower resistor may vary depending on the specific model and year of your Toyota Townace Noah with a 3S engine. If you are unsure about the location or how to access the blower resistor, it is recommended to consult a professional mechanic or the vehicle's owner's manual.
It is important to handle the blower resistor with care, as it can be easily damaged if not handled properly. If you are not confident in your ability to replace the blower resistor, it is best to seek assistance from a qualified mechanic.

Here's a link your blower motor. Repair Guides Blower Motor Removal Installation AutoZone com

Try to check the power and ground on the blower fan. If you missing the ground on the blower fan connector than most likely it is the blower fan resistor (controller), it is located under the hood close to back firewall behind left cylinder head.

Hi Kathy,here's a link to where your blower motor is,in the pic,the dark part is your blower motor resistor,just remove electrical connector and 2 screws holding it on,very easy. Repair Guides Blower Motor Removal Installation AutoZone com Here's a pic of your resistor. Blower Motor Resistor at AutoZone com Best Blower Motor Resistor Parts for... Don't disconnect your negative battery terminal,will cause problems.

Hi Carlos,here's a link to your blower motor,the resistor is located next to the blower,2 screws hold it on,just remove electrical connector and screws and take to Autozone and match up,very easy to do. GET 25 GIFT CARD FOR EVERY 100 SPENT ON ONLINE SHIP TO HOME ORDERS Here's the part. Heater Blower Motor Resistor at AutoZone com Best Heater Blower Motor...

Take it out,go to Autozone,get another and install,if that don't work they will take back,but you can't tell by looking at it.Here's what it look's like. Heater Blower Motor Resistor at AutoZone com Best Heater Blower Motor... Here's another link to look at,to remove resister,disconnect electrical plug,remove two screws with a phillips screwdriver,it's located next to blower motor. SAVE 20 GET 10 GIFT CARD ON ONLINE SHIP TO HOME ORDERS OVER 100

This is a common problem. It is much more common in vehicles that do not move for several days at a time. It is usually caused by rodents getting into the blower housing and building nests.

The blower motor assembly must be removed to clean out the debris. Here are the instructions for your vehicle:

BLOWER MOTOR

Removal and Installation

Disconnect the negative battery cable. Remove right front door scuff plate. Remove kick panel. Remove lower dash trim panel. Unplug blower motor connector. Remove blower motor. To install, reverse removal procedure.

CHECK BLOWER MOTOR FUSE AND RELAY.IF ALL IS GOOD.BEST TO REMOVE BLOWER MOTOR HOTWIRE IT.IF DONT WORK REPLACE BLOWER MOTOR.IF BLOWER MOTOR WORKS.YOU HAVE FAULTY CONTROL SWITCH OR MODULE.BESURE TURN OFF RADIO FIRST YOU NEED TO REMOVE NEGATIVE BATTERY CABLE.WAIT 15 MINUTES BEFORE WORKING UNDER DASH.THIS WILL DISARM AIRBAG AND BCM UNDER DASH.YOUR BLOWER MOTOR UNDER DASH ON THE PASSENGER SIDE FAR TO BACK.YOU NEED TO REMOVE BOTTOM PANEL TO GET TO IT.

Hi!!
Check under dash, passenger side, if necessary, remove cover to access Blower Housing Assy., the harness has two terminals, one for the Blower Motor and one for the Blower Motor RESISTOR which is fastened by two 7 or 8 mm. screws to the Housing.
Here is a picture of the Blower Housing Assy. showing the Resistor.

Good Day!! A HELPFUL - 4 THUMBS - rating for this solution would be greatly appreciated. Thank you for using FixYa.

1. Remove right side scuff plate.
2. Pull back carpet.
3. Disconnect blower motor wiring connector.
4. Remove blower motor retaining screws, and lower blower motor assembly from unit housing.