Removing rear drum

Wheel Bearings

Print
Adjustment

2002-05 Models

1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
2. Remove or disconnect the following:
   
   Rear wheel Brake drum Hub cover Cotter pin Lock nut cover
3. Adjust the locknut to achieve wheel bearing play of 0.001-0.006 inches (0.025-0.152 mm).

Removal & Installation

2002-05 Models

1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
2. Remove or disconnect the following:
   
   Rear wheel Brake drum Hub cap Cotter pin Lock nut cover Lock nut Wheel bearing retainer washer and the outer wheel bearing Hub assembly Grease seal Inner wheel bearing
3. Clean and inspect the wheel bearings and races for unusual wear or damage. Replace parts as necessary.

To install:

1. Pack the wheel bearings with grease for assembly.
2. Install or connect the following:
   
   Inner wheel bearing Grease seal Hub assembly Lock nut. Adjust the locknut to achieve wheel bearing play of 0.001-0.006 inches (0.025-0.152 mm). Lock nut cover Cotter pin Hub cap Brake drum Rear wheel
   

Rear Brake Discs

• Fotolia.com" data-type="modal"> Replace the bearing and race as a single set. automotive roller bearing. image by Tom Oliveira from Fotolia.com

  Before raising the rear of your Honda, remove the dust cup from the center of the brake drums using a hammer and chisel. This will give you access to the spindle nut, which you can loosen using an axle nut socket. Then you can raise and remove the wheel/tire assembly ,or assemblies if you are replacing the bearings on both wheels.
  

  If your Honda model is equipped with rear disc brakes, remove the brake disc retaining screws, the brake hose bracket from the steering knuckle and caliper bracket mounting bolts. Hang the caliper to the coil spring using wire. Do not let the caliper hang free or the brake hose may be damaged.
  

  At this point, you will be able to remove the brake disc by hand. However, rust may have a firm grip on the disc. If this is the case, use a couple of 8-by-1.25 mm bolts and screw them evenly into the brake disc threaded holes. This will push the disc off the hub. Now you can finish removing the spindle nut and hub/wheel bearing assembly and install the new hub/wheel bearing assembly using a new spindle nut
  

Read more: Honda Rear Wheel Bearing Removal ' eHow.com http://www.ehow.com/way_5974291_honda-rear-wheel-bearing-removal.html#ixzz1W3WDRoqv Rear Brake Drums

• Fotolia.com" data-type="modal"> Pack the bearing with bearing grease before installation. roller bearing image by Tom Oliveira from Fotolia.com

  If your Honda Civic comes equipped with rear brake drums, remove the center grease cup and loosen the axle spindle nut using an axle nut socket. After raising and removing the wheel/tire assembly, finish removing the axle nut and washer.
  

  You might be able to remove the outer wheel bearing from the spindle using a screwdriver. If not, wiggle the brake drum as you pull on it to let the bearing fall off the spindle. However, the brake drum might be caught in place by the brake shoes. In this case, you can retract the brake shoes through the hole in the back of the backing plate.
  

  Remove the rubber plug from the back of the backing plate. Then rotate the star wheel on the adjusting screw using a brake adjusting tool as you push the lever off the start wheel with a screwdriver. With the brake shoes off the brake drum, pull the brake drum off the wheel assembly. Then clean the brake assembly with brake parts cleaner and a clean, lint-free towel.
  

  Now you can set the brake drum on a workbench or hard surface and remove the grease seal and inner wheel bearing. The inner and outer wheel-bearing races can be removed using a drift punch and hammer. Pack the new wheel bearings with high-temperature wheel-bearing grease using a wheel-bearing packer and use a new grease seal during installation. Also, before reinstalling the brake drum, apply a thick coat of wheel-bearing grease to the cavity inside the hub, but do not fill it completely.
  

Read more: Honda Rear Wheel Bearing Removal ' eHow.com http://www.ehow.com/way_5974291_honda-rear-wheel-bearing-removal.html#ixzz1W3WN9eBb

Adjustment

1. Place parking brake lever in -full released- position.
2. Raise and support vehicle.
3. Remove plug in parking brake shoe support to access adjuster star-wheel.
4. Through the access hole, rotate the adjuster star wheel in the following direction to expand the shoes outward against the drum:
   1. Left brake - Rotate star-wheel toward rear of vehicle.
   2. Right brake - Rotate star-wheel toward front of vehicle.
5. Using an appropriate tool, turn adjuster star wheel until wheel will not rotate (dead lock).
6. Back off adjuster six detents (teeth).
7. Rotate wheel, checking for light drag. If drag is too heavy, continue to back off adjuster one detent at a time until light drag is present. Do not back off star-wheel more than 17 detents from wheel lock.
8. Install access plug.
9. Adjust opposite wheel parking brake shoes using same method.
10. Lower vehicle.
11. Apply and release parking brake lever once to ensure proper operation of parking brakes.

Removal & Installation NOTE The following procedure may be used to remove shoes on either side of the vehicle.

1. Lock out automatic adjuster in parking brake lever.
2. Raise and support vehicle.
3. Access and remove rear hub and bearing.
4. Remove parking brake cable bolt at knuckle.
5. Completely back off parking brake shoe adjustment.
6. Remove parking brake shoe adjuster spring.
7. Remove shoe adjuster.
8. Remove upper brake shoe hold-down clip and pin.
9. Remove lower brake shoe hold-down clip and pin.
10. Remove upper and lower shoes with return spring from shoe actuator.
11. Remove return spring from shoes.
    
    

    Fig. View of the actuator (1), support (2), adjuster spring (3), return spring (4), caliper adapter (5), shoes (6), hold-down clips and pins (7) and adjuster (8)
    

To install:

1. Install return spring between upper and lower shoes.
   NOTE Before installing shoes on actuator, make sure actuator hooked to rear cable is positioned with word -UP- facing outward.
2. Install upper and lower shoes with return spring on shoe actuator located on parking brake cable.
3. Install lower brake shoe hold-down pin through rear of support and lower shoe, then install hold-down clip.
4. Install upper brake shoe hold-down pin through rear of support and upper shoe, then install hold-down clip.
5. Install shoe adjuster. Place end of adjuster with star wheel upward.
6. Install parking brake shoe adjuster spring.
7. Install bolt securing parking brake cable to knuckle and tighten bolt to 21 ft. lbs. (28 Nm).
8. Using Brake Shoe Gauge, Special Tool C-3919, or equivalent, measure inside diameter of parking brake drum portion of rotor.
9. Place Gauge over parking brake shoes at widest point.
10. Using adjuster star wheel, adjust parking brake shoes until linings on both park brake shoes just touch jaws on gauge. This will give a good preliminary adjustment of parking brake shoes, before a final adjustment is made at end of this procedure.
11. Install hub and bearing with wheel speed sensor as well as all components necessary to access it.
12. Lower vehicle.
13. Unlock automatic adjuster in parking brake lever.
14. Perform final adjustment of parking brake shoes

15. 
    Adjustment This vehicle is equipped with permanently sealed rear wheel bearings. There is no periodic lubrication or maintenance recommended for these units.
    

    
    Removal & Installation

    1. Raise and support vehicle.
    2. Remove wheel mounting nuts, then tire and wheel assembly.
    3. If equipped with AWD:
       1. Remove cotter pin, nut lock and spring washer from half shaft.
       2. While a helper applies brakes to keep hub from turning, remove hub nut and washer.
    4. Remove brake caliper and rotor from hub and bearing assembly.
       
       

       Fig. Hub assembly
       

    5. Disconnect vehicle wiring harness connector at wheel speed sensor connector.
    6. Unclip wheel speed sensor connector from spare tire mounting support.
    7. Disconnect two sensor cable routing clips on rear suspension crossmember.
    8. Disconnect two sensor cable routing clips along toe link.
    9. Disconnect sensor cable from bracket on brake support.
       
       
    10. Completely loosen, but do not remove four bolts fastening hub and bearing in place. Once loosened from threads in hub and bearing, push bolts up against rear of hub and bearing to keep brake support plate in place when hub and bearing is removed.
        
        

        Fig. Rear hub and bearing mounting bolts
        

    11. Pull hub and bearing off knuckle and half shaft (if equipped with AWD), then thread wheel speed sensor cable through hole in brake support plate as it is removed with hub and bearing.
        
        
    To install:
    
    1. Position hub and bearing bolts though rear of knuckle and parking brake support just enough to hold support in place as hub and bearing is installed.
    2. Install hub and bearing by first feeding end of wheel speed sensor cable through hole in bottom of parking brake support. As this is being done, if equipped with AWD, slide hub and bearing onto half shaft. Place hub and bearing through brake support, onto knuckle, lining up mounting bolt holes with bolts and placing wheel speed sensor head at bottom.
    3. Install four bolts fastening hub and bearing in place. Tighten mounting bolts to 60 ft. lbs. (81 Nm).
    4. Place wheel speed sensor cable routing grommet into bracket on parking brake support.
    5. Route wheel speed sensor cable along toe link and rear suspension crossmember connecting routing clips where shown.
    1. Connect vehicle wiring harness to wheel speed sensor connector.
    2. Install brake rotor and caliper.
    3. If equipped with AWD:
       1. Install washer and hub nut on end of half shaft.
       2. While a helper applies brakes to keep hub from turning, tighten hub nut to 180 ft. lbs. (244 Nm).
       3. Install spring washer, nut lock and cotter pin on end of half shaft.
    4. Install tire and wheel assembly. Install and tighten wheel mounting nuts to 100 ft. lbs. (135 Nm).
    
    
    

    
    
    

Light Duty Models

1. Raise the vehicle so that the wheel to be worked on is clear of the floor and install jackstands under the vehicle.
   
2. Remove the wheel. Remove the three retaining nuts and remove the brake drum. It may be necessary to back off the brake shoe adjustment in order to remove the brake drum. This is because the drum might be grooved or worn from being in service for an extended period of time.
   
3. Before installing a new brake drum, be sure to remove any protective coating with brake cleaner or a suitable fast-drying degreaser.
   
4. Install the brake drum in the reverse order of removal and adjust the brakes.
   

Heavy Duty

1. Raise the vehicle and install jackstands.
   
2. Remove the wheel. Loosen the rear brake shoe adjustment.
   
3. Remove the rear axle retaining bolts and lockwashers, axle shaft, and gasket.
   
4. Remove the wheel bearing locknut, lockwasher, and adjusting nut.
   
5. Remove the hub and drum assembly from the axle.
   
6. Remove the brake drum-to-hub retaining screws, bolts or bolts and nut. Remove the brake drum from the hub.
   

To install:

1. Place the drum on the hub and attach it to the hub with the attaching nuts and bolts.
   
2. Place the hub and drum assembly on the axle and start the adjusting nut.
   
3. Adjust the wheel bearing nut and install the wheel bearing lockwasher and locknut.
   
4. Install the axle shaft with a new gasket and install the axle retaining bolts and lockwashers.
   
5. Install the wheel and adjust the brake shoes. Remove the jackstands and lower the vehicle.
   

// // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 32; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]> // // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 32; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]>

If the following is not enough then maybe try Alldata.com which generally has more information, but it will cost: REMOVAL & INSTALLATION Chrysler Concorde, New Yorker, LHS Dodge Intrepid Eagle Vision

1. Remove the rear wheels and brake drums.
2. Remove the dust cap from the rear hub and bearing assembly.
3. Remove the cotter pin, nut retainer and wave washer. Discard the old cotter pin.
4. Remove the rear hub and bearing assembly retainer nut and washer. Remove the rear hub and bearing assembly from the spindle.
5. Remove the automatic adjuster spring from the adjuster lever.
6. Rotate the automatic adjuster starwheel enough so both shoes move out far enough to be free of the wheel cylinder boots.
7. Disconnect the parking brake cable from the actuating lever. Disconnect parking brake cable one side at a time.
8. Remove the both lower brake shoe to anchor springs.
9. Remove the 2 brake shoe hold-down springs from the brake shoes.
10. Remove the brake shoes, upper shoe-to-shoe return spring, automatic adjuster and automatic adjuster lever from the backing plate as an assembly.
11. Separate the brake shoes from the automatic adjuster mechanism.
12. Remove the brake shoe automatic adjuster lever from the leading brake shoe. To install:
    
13. Thoroughly clean and dry the backing plate. To prepare the backing plate, lubricate the bosses, anchor pin and parking brake actuating lever pivot surface lightly with lithium based grease.
14. Remove, clean and dry all parts still on the old shoes. Lubricate the starwheel shaft threads with anti-seize lubricant.
15. Assemble both brake shoes, the top shoe to shoe return spring, automatic adjuster and automatic adjuster lever before mounting on vehicle. Make sure the ends of the automatic adjusters are positioned above the extruded pins in the webbing of the brake shoes prior to installation.
16. Install the brake shoe assembly onto the brake support plate and install the hold-down springs.
17. Install the lower anchor springs and reconnect the parking brake cable to the park brake lever of the trailing brake shoe.
18. Rotate the serrated adjuster nut to remove the free-play from the adjuster assembly.
19. Install the automatic adjuster lever spring on the lead brake shoe assembly and the automatic adjuster lever.
20. Install the rear hub and bearing assembly. Install washer and retainer nut and torque to 124 ft. lbs. (168 Nm).
21. Install the wave washer, nut retainer and a new cotter pin onto the spindle. Install dust cap.
22. Adjust brake shoes so not to interfere with brake drum installation. Install the rear brake drum. NOTE: After installing the brake drums, pump the brake pedal several times to partially adjust the brake shoes. To verify proper operation of the self-adjusting parking brake, be sure that both rear brakes are not dragging when the parking brake pedal is released.
    
23. Install the rear wheels and lug nuts. Torque the lug nuts, in a star pattern sequence, to 95 ft. lbs. (129 Nm).
24. Road test the vehicle. The automatic adjusters will continue brake adjustment during the road test of the vehicle.

Yes, Undo the 32mm nut, first. And, don't get the bearings dirty with dust from the brake drums, or , if you do, replace the inner and outer bearings with new greased up ones. REAR DRUM BRAKES Brake Drums REMOVAL & INSTALLATION CAUTION
Brake linings contain asbestos. Asbestos is a known cancer-causing agent. When working on brakes, remember that the dust which accumulates on the brake parts and/or in the drum contains asbestos. Always wear a protective face covering, such as a painter's mask, when working on the brakes. NEVER blow the dust from the brakes or drum.

1. Raise the vehicle and support safely.
2. Remove the wheel and tire assembly.
3. On vehicles without rear bearing hub, remove the dust cap, cotter pin, nut lock, wheel bearing nut and washer from the spindle. Remove the outer wheel bearing. Remove the drum with the inner wheel bearing from the spindle. If the drum is difficult to remove, remove the plug from the rear of the backing plate and push the self adjuster lever away from the star wheel. Rotate the star wheel to retract the shoes. Remove the grease seal.
4. If equipped with a rear bearing hub, remove the drum by removing the retainer screws from the drum and pulling the drum from the hub assembly. If the drum is difficult to remove, remove the plug from the rear of the backing plate and push the self adjuster lever away from the star wheel. Rotate the star wheel to retract the shoes. To install:
   
5. On vehicles equipped without rear bearing hub, lubricate and install the inner wheel bearing. Install a new grease seal. Install the drum to the spindle. Lubricate and install the outer wheel bearing, washer and nut. Adjust the bearing preload following the procedure outlined in the "Rear Wheel Bearing'' of this section. When the bearing preload is properly set, install the nut lock and a new cotter pin. Install the grease cap.
6. On vehicles with rear bearing hub, install the brake drum to the hub assembly and install the retaining screws.
7. Install the wheel and tire assembly. Adjust the rear brakes as required.
8. Apply the brakes until a firm pedal is obtained, prior to moving the vehicle.

Loosen the rear lug nuts, jack up the car, remove the rear wheels, remove the brake drums, remove the brake shoes and hardware, remove the 4 bolts holding the hubs in. Bolt in the new hubs, reassemble the brake shoes and hard ware, put the brake drums on, put the wheels on and snug the lug nuts, lower the car, tighten the lug nuts.

Ok,remove wheel.The brake drum will come off with the hub as an assembly.Make sure the brake shoes are backed off enough to remove the assembly.If the inside of the drum isn`t worn to much,the drum will come off with a little effort.There will be a grease cap you need to remove.A large pair of channel lock pliers might work,if not try a flat head screwdriver and a hammer.There will be a lip around the grease cap sitting flush against the hub.Take the screwdriver and gently tap under the flange lip to see if the grease cap will start to move out away from the hub.Tilt the screwdriver handle towards the car,and tap the end of the screw driver so the cap will move toward you,away from car.Now go to the opposite side of the cap from where you are with the screwdriver now,and do the same thing.It can be a hassle to get it off without bending or peircing the cap.Continue until cap is removed.Two types of retaining nuts can be on this spindle.Look for a cotter pin going threw the nut(if it has a pin).Use a pair of needle noise pliers,and make the pin straight.You might use a pair of ****,or wire cutters to pull the cotter pin out.(remember to replace it with a new one when you go back with the new bearings)take the channel lock pliers and turn the nut counter clock wise to remove.It may have a cage around the nut you have to remove before you remove the nut with the channel lock pliers.If you have a nut without a cotter pin,then you have a lock nut.Lock nuts have to be removed with a lot more effort.Use a socket and a ratchet.and remove in the same order.There will be a large flat washer behind the nut after you remove the nut.Shimmey the brake drum back and forth side to side,and use the flat head screwdriver to helpremove the washer.The outer bearing is next,shimey the drum agai,or pull drum forward and remove drum and bearing.If it will not slide off easy.Use a peice of wood against the outer lip of drum,on back side and tap with hammer hard all the way around(please use goggles).If it does not try to come off,back brake adjuster off so brake shoes will let go.The inner bearing is on the inside of the drum.After you have the brake drum assembley in your hand,screw the nut back on the spindle about 5 or6 turns by hand.Put the drum back on until the nut is on the outside and you can see it.Now pick upward on drum and slide drum toward you about half way and stop and let the drum hang there.The nut should be half way inside the drum.With out picking up on the drum grasp drum and pull hard and fast toward you and the inner bearing and seal should be hanging on the spindle.To install new bearings ,pack the bearings with wheel bearing grease really good(they should have enough grease in them if they are not real easy to turn by hand.To remove the race(inner and outer)take a punch and place it on the race from the opposite side of where the race will come out(the race will come out the same side the bearing came out).Flip the drum(hub)over and remove the other race.Install the same way.but make sure the race is turned the right way(cup side out,not in)The bearing has to sit in the race.Ok the inner bearing is first to put in,then the seal.Tap the seal in with a hammer(also cup side in).Take the drum(hub)and slide it back on go over the the spindle,by twisting and pushing lightly,it has to go over a shoulder on the spindle.Then put the outer bearing in and the washer(notice the washer has a alienment that it will only go on one way).Now take the nut and put in on by hand .Take the channel lock pliers and tighten the nut until snug.Move the drum back and forth and tighten some more ,and alien the hole for the new cotter pin you purchsed and put the pin in.Bend the cotter pin so it can`t come out,and replace the grease cap and tap it on with hammer lightly,install wheel,and adjust brakes.To adjust brakes spin wheel and adjust brakes until the brake shoes start touching the drumuse a brake spoon).You are finished.

Rear DRUM instructions are first If you would Like Pictures and all They Must Be Emailed as TOO LARGE For FixYa's Format im at aol.com
Just use my Knickname@ and let me know where to send.

1. Raise and support rear of vehicle, then remove wheel and tire assembly.
2. Remove brake drum. If brake drum cannot be removed easily, insert a suitable screwdriver through hole in backing plate, then push adjuster lever away from adjuster and back of adjustment tension.
3. Remove tension spring, using a suitable tool, then remove rear shoe hold-down spring and pin. Remove rear brake shoe and anchor spring, Fig. 7.
   1. On Land Cruiser models, remove front hold-down spring using a suitable tool, then disconnect the parking brake cable from the parking brake bellcrank, Fig. 7.
   2. On Pickup, 4Runner, 4WD T100 and 4WD Tacoma models, remove front shoe hold-down spring and pin, using a suitable tool, then disconnect No. 1 parking brake cable from No. 3 parking brake bellcrank.
   3. On 2WD T100 models, proceed as follows:
   1. Remove E-ring, then automatic adjusting lever and C-washer, then parking brake lever. Disconnect brake line from wheel cylinder using a suitable container to catch fluid.
   2. Remove wheel cylinder. Remove following parts from wheel cylinder: two boots, two pistons, two pistons cups and spring.
   1. On models except 2WD T100, remove front brake with strut, then disconnect parking brake cable from front shoe. Remove parking brake cable No. 2.
   2. Remove adjusting lever spring, then the adjuster from front shoe.
   Inspection
   
   1. Measure brake drum inside diameter. Inside diameter should be 11.61 inches,
      1. Measure brake shoe lining thickness, Fig. 3. Minimum thickness should be .04 inch on models except on T100 models and .039 inch on T100 models.
      2. Inspect brake lining and drum for proper contact and replace drum or shoes as necessary.
      3. Inspect wheel cylinder for corrosion or damage.
      4. Inspect backing plate for wear or damage.
      5. Inspect bellcrank components for bending, wear or damage.
      6. Apply a suitable lubricant to backing plate contact areas.
      Installation
      
      1. On 2WD T100 models, proceed as follows:
      1. Apply lithium soap base glycol grease to piston cups, pistons and boots.
      2. Assemble and install wheel cylinder.
      3. Connect brake line to cylinder.
      1. Apply high temperature grease to following parts:
      1. Backing plate and brake shoe contact points.
      2. Anchor plate and brake shoe contact points.
      3. Adjusting bolt.
      4. Adjuster and brake shoe contact points.
      1. Apply a suitable lubricant to adjuster bolt threads and end.
      2. Assemble adjuster to lever, then install adjuster lever spring.
      3. On Land Cruiser models, install parking brake lever cable to parking brake shoe, then attach cable to bellcrank.
      4. On Pickup, 4Runner, 4WD T100 and 4WD Tacoma models, install No. 1 parking brake cable to parking brake lever shoe, then attach the other side of cable to No. 3 bellcrank.
      5. Position front shoe in place with end of shoe inserted into piston, then install shoe hold-down spring and pin using a suitable tool.
      6. Assemble anchor spring to front and rear shoe, then install rear shoe with end inserted in piston.
      7. Install rear shoe hold-down spring and pin, then the tension spring.
      8. If necessary, adjust bellcrank as follows:
      1. Lightly pull bellcrank in direction "A", Fig. 8, until there is no slack in part "B".
         1. Rotate adjusting bolt until dimension "C" is .016-.031 inch.
         2. Lock adjusting bolt with locknut, when connect parking brake cable to bellcrank.
         3. Install tension spring.
         1. Ensure proper parking brake travel.
         2. Pull adjusting lever cable upward, then release and ensure adjusting bolt rotates. If bolt does not rotate, check for improper installation of rear brakes.
         3. Adjust strut to shortest possible length, then install drum.
         4. Pull parking brake lever fully upward. Repeat process several times.
            1. Remove drum, then check for proper clearance, Fig. 4. Clearance should be .024 inch. If clearance is not as specified, check parking brake system.
            2. Install brake drum, then bleed and refill brake system.
            3. Install wheel and tire assembly, then lower vehicle.

FRONT ROTORS & PADS

1. Remove caliper.
2. Remove cap and snap ring, Fig. 10, then remove cone washers with tapered punch.
3. Insert suitable length bolts into flange bolt holes, then tighten bolts evenly and remove flanges.
4. Remove free wheel hub cover and snap ring, then remove nut, spring washer and cone washer with suitable tapered punch.
5. Remove free wheel hub body and gasket.
6. Remove locknut, lock washer and adjusting nut.
7. Remove axle hub and brake disc as an assembly.
8. Remove oil seal and inner bearing from hub.
9. Reverse procedure to install. Torque adjusting nut to 43 ft. lbs., then back off nut. Torque nut to 18 ft. lbs. Using spring scale attached to hub bolt, check that preload is 1.4-12.6. Install lockwasher and locknut, if equipped. Torque locknut to 35 ft. lbs., and recheck preload. Secure lockwasher by bending one tab inward and one tab outward.

1. Raise and support front of vehicle, then remove tire and wheel assembly.
2. Remove clip and hole pins, Fig. 9.
3. Remove anti-rattle spring and shim(s) if equipped, then remove brake pads.
4. Lubricate caliper housing with suitable brake grease at pad contact points.
5. Reverse procedure to install.

Did you get an answer to your question?