Question about 2003 Kia Spectra

1 Answer

How to change rear barke shoes - 2003 Kia Spectra

Posted by on

  • Amanda Drew
    Amanda Drew Dec 07, 2017

    I'm also wondering how to change some of my brake shoes. My problem, though, is with the front ones. They're making such a loud squealing noise whenever I press on the brakes. The two of us might just want to find a professional who can install some new ones. They'd know how to do it. http://www.gpautomotive.net/service/brak...

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Kia Master
  • 6,826 Answers

Brake Drums & Brake Shoes Removal & Installation To Remove:
Rear Drum Brakes how to change rear barke shoes - kia-09-18-7627.gif

  1. Raise and safely support rear of vehicle.
  2. Release parking brake.
  3. Remove rear wheel assemblies. NOTE: If brake drum is stuck, install two 8 mm bolts into threaded holes and tighten evenly.
  4. Remove top return spring, front and rear shoe spring clips and hold-down pins.
  5. Remove anti-rattle spring and adjuster spring. NOTE: Note position of operating lever prior to removal.
  6. Remove bottom return spring.
  7. Remove clip and washer and detach parking brake cable from rear shoe.
  8. Remove brake shoes.
To Install:
  1. Lubricate all brake shoe contact points with appropriate grease.
  2. Place operating level into position on hub.
  3. Install rear brake shoe and connect parking brake cable to rear shoe with washer and clip.
  4. Install front brake shoe and install bottom return spring.
  5. Install hold-down pins and spring clips.
  6. Position operating lever and install top return spring.
  7. Install anti-rattle spring and adjuster spring.
  8. Install brake drum and screws.
  9. Adjust brakes and install rear wheel assemblies.
prev.gif next.gif

Posted on Jan 21, 2011

Ad

2 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 118 Answers

SOURCE: Changed rear brake shoes, Right rear locks up

Check adjustment, and put a new spring kit in. The old ones might be weak and used.

Posted on Nov 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a chevy 2500 hd when i turn turn the rear wheels skip and bark


Chances are the locking rear differential is staying locked up and causing the tires to chirp/bark.You can try to fix this by changing the rear axle grease and then driving i circles both left and right about 20 times.If it starts to get better then try it for awhile.If not the rear locking DIFFERENTIAL MAY NEED TO BE REBUILT.Some other possible things to check before you go
and teardown the rear axle are-different tire sizes in the rear,the vehicle is in 4wd.

Apr 13, 2011 | Chevrolet 2500 Cars & Trucks

1 Answer

I just had my 2002 Yukon XL rear barkes replaced. New calipers and pads,the parking brake doesn't work. Shouldn't they have found that when they were doing this work?


Of course they should have checked the parking brakes too. On the Yukon XL, the parking brakes are brake shoes that operate inside of a drum that is molded to the interior side of the rear disc brake rotors. I would take it back to the shop and voice my frustration if I were you and tell them that you feel they should do the parking brakes at no charge for your time and aggravation. They were right there to replace them if they re-surfaced your rotors anyway!

Feb 21, 2011 | 2002 GMC Yukon XL

2 Answers

1997 Ford contour rear brake shoe replacment help.


Brake shoe removel:

Depress and turn the retainers for the hold-down springs and pins to remove them from each shoe. Slide the brake shoe assembly--including the shoes and springs--down so you can disengage the top ends of the shoes from the cylinder and tilt them to lift them past the retaining plate.

Unhook the lower retracting spring from the front brake shoe to disconnect it. Spread the shoes apart at the bottom to remove the adjusting screw, the screw's retracting spring and the adjuster lever. Remove the front brake shoe.

Pull the parking brake cable spring back with diagonal cutting pliers, grip the cable with the pliers without cutting it, unhook the cable from the parking brake lever and remove the rear brake shoe with the lever.

Disconnect the parking brake lever from the rear shoe by spreading the retaining clip with a screwdriver and removing the clip and its spring washer.
  • Step 4 Pull the parking brake cable spring back with diagonal cutting pliers, grip the cable with the pliers without cutting it, unhook the cable from the parking brake lever and remove the rear brake shoe with the lever.
  • Step 5 Disconnect the parking brake lever from the rear shoe by spreading the retaining clip with a screwdriver and removing the clip and its spring washer.

  • Read more: How to Change Rear Brakes on a 1997 Ford Taurus | eHow.com http://www.ehow.com/how_6123373_change-brakes-1997-ford-taurus.html#ixzz0u2xgUqun
  • Step 3 Unhook the lower retracting spring from the front brake shoe to disconnect it. Spread the shoes apart at the bottom to remove the adjusting screw, the screw's retracting spring and the adjuster lever. Remove the front brake shoe.
  • Step 4 Pull the parking brake cable spring back with diagonal cutting pliers, grip the cable with the pliers without cutting it, unhook the cable from the parking brake lever and remove the rear brake shoe with the lever.

  • Read more: How to Change Rear Brakes on a 1997 Ford Taurus | eHow.com http://www.ehow.com/how_6123373_change-brakes-1997-ford-taurus.html#ixzz0u2xdByQ8

  • Step 2 Slide the brake shoe assembly--including the shoes and springs--down so you can disengage the top ends of the shoes from the cylinder and tilt them to lift them past the retaining plate.
  • Step 3 Unhook the lower retracting spring from the front brake shoe to disconnect it. Spread the shoes apart at the bottom to remove the adjusting screw, the screw's retracting spring and the adjuster lever. Remove the front brake shoe.
  • Step 4 Pull the parking brake cable spring back with diagonal cutting pliers, grip the cable with the pliers without cutting it, unhook the cable from the parking brake lever and remove the rear brake shoe with the lever.
  • Step 5 Disconnect the parking brake lever from the rear shoe by spreading the retaining clip with a screwdriver and removing the clip and its spring washer.

  • Read more: How to Change Rear Brakes on a 1997 Ford Taurus | eHow.com http://www.ehow.com/how_6123373_change-brakes-1997-ford-taurus.html#ixzz0u2xVyUAt

  • Step 2 Slide the brake shoe assembly--including the shoes and springs--down so you can disengage the top ends of the shoes from the cylinder and tilt them to lift them past the retaining plate.
  • Step 3 Unhook the lower retracting spring from the front brake shoe to disconnect it. Spread the shoes apart at the bottom to remove the adjusting screw, the screw's retracting spring and the adjuster lever. Remove the front brake shoe.
  • Step 4 Pull the parking brake cable spring back with diagonal cutting pliers, grip the cable with the pliers without cutting it, unhook the cable from the parking brake lever and remove the rear brake shoe with the lever.
  • Step 5 Disconnect the parking brake lever from the rear shoe by spreading the retaining clip with a screwdriver and removing the clip and its spring washer.

  • Read more: How to Change Rear Brakes on a 1997 Ford Taurus | eHow.com http://www.ehow.com/how_6123373_change-brakes-1997-ford-taurus.html#ixzz0u2xVyUAt

    Jul 17, 2010 | 1995 Ford Contour

    1 Answer

    Changed rear brake shoes, Right rear locks up


    Check adjustment, and put a new spring kit in. The old ones might be weak and used.

    Nov 04, 2009 | 1996 Dodge Ram

    1 Answer

    Rear rotors stuck on e brake shoes. Tried turning off, hammering off, loosing the e brake adjuster. The pins look broken holding the shoes on since the bottom part of the rotor pulls way out but can't get...


    When i did my brakes on my 05 grand caravan i turned the parking brake adjuster and hammered like crazy till they came off then i replaced parking brake shoes and hardware they are never saved and after you have replaced that you need to adjust parking barke shoes.

    Jul 02, 2009 | 2005 Dodge Grand Caravan

    1 Answer

    1999 nissan quest rear brake shoes need changing


    help is here:
    http://autos.groups.yahoo.com/group/villagerquest/

    Drum Removal
    1. Remove the rear wheel and the tire assembly. Refer to Section 204-04 .
    1. Retract the brake shoes and loosen the brake adjuster screw.
    975565f.gif
    1. Remove the brake drum.
    ----------------------
    May require big hammer to loosen drum from axle flange. Hit between the the lugs, not on them.

    ------------------------------------------------------------------------------
    #10 is access plug to back off adjusting wheel.

    f9f31b5.gif
    Item Part Number Description 1 2261 Rear wheel cylinder 2 — Dust boot (part of 2128) 3 2197 Wheel cylinder piston (part of 2261) 4 — Cup (part of 2128) 5 2204 Wheel cylinder piston cup spring (part of 2128) 6 — Wheel cylinder housing (part of 2261) 7 — Brake shoe hold-down pin 8 — Access hole (part of 2212) 9 — Rear brake bleeder screw (part of 2261) 10 — Access hole plug 11 — Rear wheel cylinder bolt 12 2212 Rear brake backing plate 13 — Rear brake backing plate bolts 14 2N790 Parking brake lever clip 15 — Spring washer 16 — Secondary brake shoe and lining (part of 2200) 17 — Brake shoe hold-down spring (part of 2B514) 18 — Lower retracting spring (part of 2B514) 19 2A637 Parking brake lever 20 — Parking brake lever pin 21 2A177 Brake shoe adjusting lever 22 — Adjuster lever pin (part of 2A177) 23 — Primary brake shoe and lining (part of 2200) 24 — Upper retracting spring (part of 2B514) 25 2041 Brake adjuster screw

    --------------
    Shoes Removal

    Take a picture and remember how each part goes and attaches
    1. Remove the brake drum, refer to Drum in this section.
    1. Remove the upper retracting spring.
    1. Remove the lower retracting spring.
    1. Remove the self-adjuster.
    38bcaa0.gif
    1. Remove the hold-down springs.
    1. Remove the parking brake lever clip and the parking brake lever.

    Apr 17, 2009 | 1999 Nissan Quest

    1 Answer

    Rear brake drum has been changed to some other car drum and shoe


    please explain properly if you want help

    ?????????????????????????????????????????????????????????????????????????????????/

    Apr 02, 2009 | 2003 Kia Rio

    1 Answer

    How to change rear brake shoes on a 2004 chevy venture


    The rear brake shoes use a U clip to hold the shoes together. A simple solution to this change job is to change one side at a time.
    Slowly unclip the U clip from the top of the shoe and remove the left shoe and spring. Replace the left shoe and reconnect the U clip, then do the same for the other shoe. Clean, adjust,and grease the self adjuster and you're done. Do the same for the other side of the van. If you take both sides of the clip off you're in for some heavy duty stretching with pliers unless you have the right tool.

    Dec 29, 2008 | 2004 Chevrolet Venture Passanger

    3 Answers

    Remove rear brake drums


    0f2c8a8.gif
    1. After removing the wheel, remove the brake drum. 2. Remove the shoe hold down spring, the automatic adjuster spring and adjuster lever.
    7b7d17f.gif
    3. Spread the shoes and remove the shoe adjuster. 4. Remove the shoe to shoe spring and shoe hold down spring.
    a1a62c3.gif

    Jun 03, 2008 | 1999 Hyundai Accent

    Not finding what you are looking for?
    2003 Kia Spectra Logo

    1,613 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Kia Experts

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22485 Answers

    Marvin
    Marvin

    Level 3 Expert

    85216 Answers

    Jonah Oneal

    Level 3 Expert

    14092 Answers

    Are you a Kia Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...