BATTERY WHERE IS THE BATTERY LOCATED ON THE 2002 CHRYSLER PT CRUISER & HOW DO YOU REMOVE IT!?

mike loshbough

• 1011 Answers
• Posted on Jan 25, 2009

SOURCE: where is the crank sensor located on 2005 chrysler pt cruiser?

the crank sensor is located on back right side of engine by were the trans. bolts up.is the no start when could or hot?

SOURCE: Change the thermostat on 2002 Chrysler PT Cruiser

Hi, i have put together a step by step guide that will help you with this replacement job. Make sure the vehicle is in a cool state before starting this job.


* Drain some coolant into a clean container until the coolant level is below the thermostat housing.
* Remove the upper radiator hose connection from the thermostat housing.
* Loosen the housing bolts and remove the housing.
* Remove the gasket and scrape it carefully from the surface of the housing and the mounting surface on the engine. If the gasket remains on either of the surfaces, there will probably bea coolant leak after reassembly. Some engines use a rubber O-ring to seal a thermostat housing.
* Compare the size of the thermostat to the old one. They are of different sizes, types, and temperature ratings.
* The temperature rating is stamped on the sensing bulb on the bottom of the thermostat. The temperature bulb faces the block.
* When replacing a thermostat, be sure that the thermostat fits into the groove in the block or outlet housing. If the thermostat is installed upside down, the engine will overheat.
* Install the gasket.
* Reinstall the thermostat housing. Refill the system and run the engine or pressure test to check for leaks.
* When the engine has reached operating temperature make sure the thermostat opens.
* You should be able to see coolant circulating within the radiator.
* Another way of checking thermostat operation is to feel the top of the radiator hose or use a thermometer or multimeter with a temperature probe to confirm that the coolant is warming up.
* If the engine is overheating, but the top hose is still cool to the touch, the thermostat is stuck closed and must be replaced.

NOTE
When a paper gasket is used and the recess is in the thermostat housing, it is a good practice to position the thermostat into the recess and glue the gasket to hold it in place. If it falls out of its groove during installation, the outlet housing can be cracked or a coolant leak will result. Before tightening the water outlet housing, try to rock it back and forth to be sure it is flush. Housings are often cracked during this step.

Remontti-J

• 32 Answers
• Posted on May 30, 2009

SOURCE: 2001 Chrysler PT Cruiser Headlamp

Here is the photo how to remove headlamp splash shield
http://www.ptcruiser.fi/ptgalleria/albums/userpics/10010/normal_lampunvaihto%201.jpg

http://www.ptcruiser.fi/ptgalleria/albums/userpics/10010/normal_lampunvaihto%202.jpg

SOURCE: Describe your 2002 Chrysler PT Cruiser timing

Replace the belt at 100k with a new water pump pulley and tensioner. It would not be a bad idea while u r in there to replace the center motor mount. When the mount fails it is a pricey fix not a bad Idea to replace it since you have to remove it to do the belt.

ZJ Limited

• 17989 Answers
• Posted on Jan 22, 2011

SOURCE: where is the EGR Valve

The valve is located above where the engine and transmission seam meets; there is the metal exhaust gas tube with two bolts and a fiber gasket. The EGR mounts to the cylinder head with two 10mm bolts and a metal gasket. There are 2 vacuum lines that go to the control solenoid, a black plastic pod moounted under the throttle body. It clips into the TB mounting bracket, and has a third vacuum supply line and one electrical connector.

You can get one at Auto Zone for about $80.

Hope this helps (remember to rater this answer).