Question about 1997 Oldsmobile Aurora

1 Answer

How to install a outside car door handle - 1997 Oldsmobile Aurora

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 610 Answers

You must remove the interior door panel. then looking through the opening behind the handle, tou must remove the linkage, usuall held on with a plastic clip. then there are usually two 10 mm bolts or nuts, that secure the handle in place. remove the handle, replace it, and reinstall your door panel.

Posted on Dec 30, 2010

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2011 Hyundai sonata driver side exterior front door handle installation


first open door and find the round black rubber plug located inside the door edge,remove the plug and use a 8mm socket to remove the key lock part of the outside handle . once that is removed you grasp the outside handle side it toward the removed lock part then pull it outward very slightly with the front out first then the rear in a curve motion, reverse procedure to install new handle

Jan 14, 2018 | Hyundai Cars & Trucks

Tip

How To Install Replace Front Outside Door Handle Mercury Grand Marquis 98-11...


How To Install Replace Front Outside Door Handle Mercury Grand Marquis 98-11 1AAuto.com

on May 18, 2012 | 1998 Mercury Grand Marquis

Tip

How To Install Replace Rear Outside Door Handle Buick LeSabre 00-05 1AAuto.com


How To Install Replace Rear Outside Door Handle Buick LeSabre 00-05 1AAuto.com

on May 03, 2012 | 2000 Buick LeSabre

1 Answer

Why will driver doorl only open from inside the car?


The outside door handle broke ! you can only see what broke by taking the door panel off . It's plastic an they break ! $47.95 new 1Aauto . This video is just to show you what has to be done to get to it ! 2006 2011 Cadillac DTS Paint to Match Outside Door Handle Rear Driver Side How To Install Replace Outside Front Door Handle Cadillac DeVille 94 99...

Aug 23, 2014 | 2007 Cadillac DTS Sedan

1 Answer

Need to install outside door handle on 1996 buick regal 2 door


remove the door trim and you will see nuts inside the door skin that holds the handle assembly on.

Feb 03, 2014 | 1995 Buick Regal

2 Answers

Driver side door handle


open door remove panel,put window up,locate and remove fastner behind door handle,install opposite.

Jan 01, 2013 | Mercury Capri Cars & Trucks

3 Answers

How do I replace the driver side outside door handle on my 1996 Toyota Tacoma?


Make sure window is up. Remove inner door panel. Disconnect latch mechanism. Should be a few nuts holding handle on. Unscrew them. Install front door outside handle frame sub-assembly. Using a torx wrench (Usually T30) install the outside handle.

May 04, 2011 | Toyota Tacoma Cars & Trucks

1 Answer

How to replace a window on a 2002 saturn sl2 with power windows. i cant get the door handle assembly off


As per the Haynes manual for your vehicle.
DOOR WINDOW GLASS-REMOVAL AND INSTALLATION:
1. Remove the door outer panal.
2. Lower the window glass.
3. remove the two nuts and one screw securing the glass.
4. Remove the glass by lifting it up carefully and rotating it inward.
5. Installation is reversal of removal.

DOOR OUTER PANAL-REMOVAL AND INSTALLATION:
1. Remove door trim panal.
2. Remove the outside mirror. Remove the foam block from the mirror opening.
3. Remove the outside door handle.
4. Open the door and pry thhe outer sealing strip out of the window glass opening.
5. remove the door panal screws.
6. Detach the front and rear of the outer panel, then lift it toward the rear to remove it.
7. Installation is the reverse of the removal procedure. Apply thread locking compound to the panel retaining screws.

OUTSIDE DOOR HANDLE-REMOVAL:
1. Pull handle out and puch the centers of the retaining pins through the pins, then remove them and detach handle. (These pins are located underneath the handle.

Hope this helps, let me know if you need any other help.

Feb 06, 2010 | 2002 Saturn L-Series

1 Answer

Changing the outside door handle on a 1997 Toyota Starlet


There is two bolts that hold the window slider thing in place. One just below one of the door handle nuts inside the door and the other is on the outside of the door (on the inside of the car). Once these are removed it enables you to move that mech out of the way to get to the other bolt.

I undone the 3 latch screws to give me a bit more movement in the rod that connects to the handle too.

This should give you enough room to get to that other nut and clip the rod into the handle once installed.

Once handle is installed simply just slide the window mech back up into position and bolt back in.

-robib.

Jan 20, 2010 | 1984 Toyota Starlet

Not finding what you are looking for?
1997 Oldsmobile Aurora Logo

188 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

Jonah Oneal

Level 3 Expert

14092 Answers

Marvin
Marvin

Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...