Iv one key for the 2000 s type v8 iv bought but no key fob can i get another fob and will it work on my car

Programming a Replacement Keyless Entry Remote ' Filear ...

filear.com/?p=131

Oct 17, 2012 - If the transmitters don't work, or if you'd rather not match the transmitters yourself, .... Tried these instructions last night on my 2005 Grand Prix.

Key FOB Not Working - The Chrysler Minivan Fan Club Forums

forum.chryslerminivan.net/showthread.../11859-Key-FOB-Not-Working

Mar 15, 2009 - 10 posts - ‎3 authors
Hi Everyone, One of my Key FOB's stopped working. Is there a way of ... Well, to be honest, you don't know where that FOB has been? LOL ... 2009 Dodge Grand CaravanSXT (3.8L), Light Sandstone Metallic, 125K miles 2005 Volvo .... By jimmy154 in forum 3rd Generation Chrysler Minivans: 1996-2000.

Key May Not Start Car or Release From Ignition : Dodge ...

repairpal.com > Problems > Dodge > Grand Caravan

Dodge Grand Caravan Key May Not Start Car or Release From Ignition. ... If the newkey doesn't work, replacing the lock cylinder including tumblers ... I am able to turn off the van, but the key is stuck in the ACC position, draining my battery. ... In reading other comments, I see it may be the FOB so I'll carry both with me and ...

2009 Dodge Grand Caravan car lock doors not working

the fob on s types can only be programmed using suitable diagnostic equipment

pop open the key fob from the side and you will notice a watch battery inside the fob, replace it and make sure nothing came unsoldered from the board and that should fix the problem

Locks don't work of the ignition key.

Hi.
I have a clio II, 2001, i have the same problem and i fixed it.
Don't know if will work for you but here it goes:

1 - no key in ingnition
2 - press the unlock button in console off the car for about 10 seconds(dont let go)
3 - it should work the central doors one time and then 2 times( hear)
4 - press the remote a few times until it starts working

It worked for me hope the same for you.
Please tell me if it worked and pass the message.

Good luck

You have the wrong KEY if it won't turn any locks.
You can use the KEY fob from another Passat.
The one you have was most likey not the original
and the car was reprogrammed to except that FOB.

The Fuse panel Is inside the DRIVES side.
Open the Driver door. Look at the side of the DAShboard.
THat Giant "B" Shapped plastic cover pops off.

Check the fuses...IF any are broken,black or no good.
REplace them

Hope this helps

Sketchlab.com
MugShot Collection.

Seperate key fobs only can be programmed in the following way.

Turn ignition on/off 8 x times (allow all functions to stabilise) after the 9th on - press a button on both remote fobs. then turn ign. off. use good remote to lock and then try new remote to unlock/lock. sometimes it works first time - sometimes you have to repeat actions. good luck.

did you try calling a dealer sometimes they are the only ones that can reprogrm these things

Key fobs tend to hold their code indefintely. The batteries in them are probably burnt. Open up one of the fobs and replace the battery (hearing aid type) then they should work fine. Good Luck!~

2000 Mazda 626
Note: Make SURE the battery is new.
Instructions for programming ONE keyless remote fob.
1. Open the driver’s door & leave open.
2. Insert the key in the ignition.
3. Turn the key to the on and off position 3 times.
4. Remove the key from the ignition.
5. After door open chime stops, press the door open button 3 times.
6. After chime, press any fob key twice.
7. After second chime, press any fob key twice again.
8. After third chime, press any fob key twice again.
9. Press the door open button once.
10. The car should give another acknowledgement chime.
11. Test key fob.
This DOES work. I just programmed mine successfully today, three hours ago.