Need to replace headlight bulb. how do I access bulb?

Hi there, together with providing you the solution to the problem, I also took the liberty of going one step further in giving you steps on how to remove the headlight bulb.

• Find the hood release handle and activate it, the hood should pop open.
• Once the hood is popped open locate the hood secondary or safety latch and release it. Then finish opening the hood.
• Locate and remove mounting clips for any plastic shields that cover the headlight lens mounting screws or clips.
• Some headlight bulbs can be replaced by simply grasping the bulb socket behind the headlight lens and turn it counter clockwise to remove it. This will expose the headlight bulb.
• If the headlight bulb socket is not accessible the headlight lens may need to be remove or obstructions behind the bulb removed to gain access to the headlight bulb socket.
• To remove the headlight lens remove all mounting screws and clips that hold the headlight lens in place.
• After the headlight housing has been removed from it's mounts, release the headlight bulb from the headlight lens housing (turn counter clockwise) the bulb will then come out of the headlight assembly. Once removed, visually verify that the replacement bulb is exactly the same as the failed bulb before to ensure a proper repair.
• Clean the headlight lens free from all debris to help maintain the seal from the bulb to the lens. This will keep moisture out of the lens.
• Install the new headlight bulb by turning the retainer ring or bulb clockwise.
• Re-install the headlight lens housing and reinstall electrical connector.
• Re-install plastic covers.

After the job is complete turn the ignition key to the "on" position and activate the headlight switch. Observe the newly replaced headlight bulb to ensure proper operation.

Glad to be of help!!!

REMOVE THE HEADLIGHT ASSEMBLY
ACCESS THE HEADLIGHT FROM THE REAR OF THE LIGHT
REPLACE BULB THEN REASSEMBLE LIGHT

You can replace the headlights on your Crossfire easily by yourself. headlight image by Carbonbrain from Fotolia.com

When a headlight burns out on your Chrysler Crossfire, you do not need to rush to the repair shop to have it replaced. You can access the headlights in your Crossfire from within the engine compartment, allowing you to change the headlight yourself. The Crossfire uses an H7U headlight bulb, which you can find at auto parts retail stores or at a Chrysler dealership.
Difficulty: Easy

1. 1 Open the hood of your Crossfire to gain access to the headlight assemblies. Press down on the tab on top of the light assembly cover. Remove the cover and set it aside.
   
2. 2 Pull the electrical connection free of the bulb socket. Press the spring clamps securing the bulb into the light assembly. Pull the bulb straight out of position.
   
3. 3 Insert the new bulb in the same position. Ensure that the spring clamps secure the bulb. Press the electrical connection into place.
   
4. 4 Replace the light assembly cover and press it into position until it clicks, securing it in place. Repeat the same process on the opposite headlight if required. Close the hood and test the headlight operation.
   

H13 HALOGEN HEADLIGHT BULB, SOLD INDIVIDUALLY -- Low 55/high 65-watt halogen bulb; 12.8 volts; P26.4t base; A high quality, direct fit OE replacement headlight bulb




How to Replace a Headlight Bulb
(DIY Complexity: Easy / Time: 0.9 hour)

Parts:
1. Headlight Bulb

Tools:
1. Screwdriver
2. 1/4 in. Drive Ratchet
3. Socket Set

Steps:
Step 1 Open the hood and locate the headlight assembly.
o Tip: Most headlight assemblies have a place in the rear to gain access to the headlight bulb.
o Tip: It is recommended that headlight bulbs are replaced in pairs.
o Tip: Always make sure the struts on the hood can fully support the weight of the hood so that it does not close on you while working. The use of a hood prop can securely hold it in place.
o Tip: Safety Tip:Always wear safety glasses when working on your vehicle. Wear other personal protective equipment (PPE) when necessary, for example latex gloves or safety shoes.

Step 2 Gain access to headlight bulb.
o Tip: It is a good idea to check the high beam and low beam headlight bulbs at this time.

Step 3 Disconnect the wiring harness and replace the old headlight bulb with a new one.

Step 4 Turn on the headlights and check high and low beams to verify repairs.

Hope this help (remember rated this help). Good luck.

Locate where the wires go into the headlight on the engine side. You should be able to find the locking collar. Turn it counter clockwise and remove the bulb at this point you should just have to unplug the old bulb and reverse the process to install the new bulb.

you should not need to take housing out.

yes , you need to remove the headlight cover from the back after u move the bulb conector then there is a holder for the bulb u need to push down then move.
i hope it help ,,,, thanx

Look at the top of the headlight assembly. There is a plastic panel on top of the assembly that is held in place by two plastic pins. Remove those pins by lifting the center of the pin and then pull out the pin. Remove the panel. Then you will find two small plastic levers that will lift about 1/2 inch. They do not come out but they will release two studs that secure the assembly. After the assembly is released, slide it forward to access the bulbs you need to replace. Installation is the reverse of these procedures.

the bulb gets replaced from the back the front headlight covers do not come off .You first have to unplug the wiring connector to the bulb you are replacing which sometimes is a pain then you twist the ring that's around the bulb to unlock it from the housing then pull the bulb straight out .If the bulb your replacing is on the same side as the battery you will need to remove the battery because there wont be enough room for you to access

if you're dealing with a v6 ram air you first have to take off the black plastic clips that hold down the hard plastic housing in order to access the headlight. once thats removed you have to TWO clamps u have to pull up on EACH headlight in order to take off the headlight, from there u should be able to access your headlight and bulb.