Find fuse for wiper motor cold morning wiper

There are two relay's in the under hood fuse / relay box . Wiper relay an wiper relay 2 . Maybe one is bad . also check fuse #14 25 amp. Wiper fuse.Plus the BCM - body control module has a hand in making the wipers work . Are you familiar with automotive electronic control modules ?
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper micro relay
• Wiper 2 relay
• Wiper diode
• Windshield wiper motor
• Windshield washer pump
• Windshield washer nozzles
• Windshield washer solvent container
• Windshield wiper arm and blade assemblies
• Windshield wiper transmission
• WIP/WASH 10A fuse
• WIPER 25A fuse

Wiper/Washer System Description
The body control module (BCM) controls wiper motor low speed operation. The washer pump and high speed operation are controlled directly by the wiper/washer switch. The windshield wiper/washer switch supplies voltage on the signal circuits to the BCM for windshield wiper/washer operation. When WASH, MIST, DELAY, LOW, or HIGH is detected, the BCM energizes the wiper micro relay by suppling voltage to the relay coil. This allows battery voltage from the WIPER fuse to flow through the relay switched input then through the contacts and out the relay switched output to the wiper 2 relay switch contacts. Since the wiper 2 relay switch contacts are normally closed to the low speed circuit of the windshield wiper motor, the motor will operate at low speed.

Do you have any speed !

Possible wiper linkage has broken/seperated from wiper motor. The wiper cowling covering the linkage assembly will need to be removed to inspect/repair

This is a complex wiper system . Here are all the components involved !
The Wiper/Washer System consists of the following components:
?€¢
Windshield wiper/washer switch

?€¢
Body control module (BCM)

?€¢
Wiper 1 relay

?€¢
Wiper 2 relay

?€¢
Wiper diode

?€¢
Windshield wiper motor

?€¢
Windshield washer pump

?€¢
Windshield washer nozzles

?€¢
Windshield washer solvent container

?€¢
Windshield wiper arm and blade assemblies

?€¢
Windshield wiper transmission

?€¢
WIPER/SW 10A fuse

?€¢
WIPER 25A fuse

Circuit/System Description
The body control module (BCM) controls the wiper motor based on input from the windshield wiper washer switch. The BCM monitors the wiper washer switch through three separate signal circuits and a ground circuit. The windshield wiper switch high signal circuit is used to determine high speed wiper operation, the windshield wiper switch low signal is used to determine low speed, intermittent, and mist operation through the use of a resistor ladder, and windshield washer switch signal circuit is used to determine washer operation. The windshield wiper motor park operation is controlled by the BCM. The BCM recieves an input from the park switch to determine wiper blade position. When the wiper blades are at the bottom of the windshield glass in park position the wiper park switch will open and the circuit will be pulled up to B+ by the BCM. The park signal will be pulled to ground by the wiper motor park switch while the wiper blades are not in the park position.
The BCM controls the windshield wiper motor through two output controls, controlling two relays which determine the desired wiper speed, high or low
Diagnostic Trouble Codes (DTCs)
The body control module (BCM) monitors the voltage on the windshield wiper switch signal 2 circuit for diagnostic purposes. If the circuit is shorted to voltage while the driver is commanded OFF, the BCM will store DTC B3715. If the circuit is shorted to ground while the driver is commanded ON, the BCM will store DTC B3715. Refer to DTC B3715.
It would be best to have a factory scan tool to diagnose this problem . it would make it easier anyway .
It

wiper linkage came off at the motor? were they frozen to the windshield when you turned them on?

You screwed up the wiper motor turning it on while blades were frozen. Replace the wiper motor park plate, or get a reman wiper motor

Washer fluid is probably frozen, have you checked the fuse for the wipers? There should be an overload protection in case the blades stick

HTH

2002 Ford F-250 Windshield Wiper Motor Removal & Installation 1. Turn the ignition switch to the ON position. Turn the ignition switch ON until the wiper blades are straight up, then turn the ignition switch OFF. 2. Disconnect the negative battery cable. 3. Remove the right-hand and left-hand windshield wiper arm and blade assemblies. 4. Remove the cowl top vent panels. 5. Detach the electrical hardness connector at the windshield wiper motor assembly. 6. Remove 3 wiper motor (module assembly) retaining bolts and remove the module assembly from the vehicle. 7. Remove the wiper linkage retaining bolt and remove the linkage from the wiper motor. 8. Remove 3 retaining nuts and remove the windshield wiper motor To install; 9. Place the windshield wiper motor in position and install 3 retaining nuts. Tighten to 10-12 ft. lbs. (12-17 Nm). 10. Connect the wiper linkage to the windshield wiper motor and install the retaining bolt. Tighten the bolts to 14 ft. lbs. (20 Nm). 11. Place the wiper motor (module assembly) in position and install 3 retaining bolts. Tighten the bolts to 6 ft. lbs. (9Nm). 12. Install the electrical hardness connector to the windshield wiper motor. 13. Connect the negative battery cable. 14. Allow the windshield wiper motor to cycle several times while checking for proper wiper motor operation. 15. Turn the windshield wiper motor to the OFF position to park the wiper motor in the park position. 16. Install the cowl top vent panels. 17. Install the wiper arm and blade assemblies. Install the retaining nuts and tighten to 22-29 ft. lbs. (30-40 Nm). 18. Connect the negative battery cable. 19. Check the windshield wiper motor for proper operation and the wiper arms for adjustment.

Dear joelgoodison,

Could be the Fuse!
Could be the Wiper Motor Burn't Out if Blades were frozen to windshield when turned on
Until you fix the problem you can buy RainX Wipe-On Glass Solution or Windsheild Washer Fluid which as unbelievable as it sounds will allow you to drive in the all but the worst downpours of rain without wipers!
I love the RainX Windsheild Washer Fluid and rarely use my wipers.
Check the fuses and try RainX and get back to me!
Hope this Helps!
jack

If the wipers were buried under snow/ice or frozen to the windshield, you may have blown the red 10 amp fuse located in cavity 9 in the fuse block located on the bottom left side of the instrument panel near the parking brake pedal.
In order of easiest to check:
1) ensure wipers not frozen to windshield.
2) ensure wiper arms are not loose on the pivot stud,
3) check the red 10 amp fuse.
You stated that "you can hear the motor". Which motor do you hear? The engine or the wiper motor?
If you hear the wiper motor, then the fuse is alright. Try 1) and 2) above.
PT Stanley

put cold water over them not hot