1997 Jeep Grand Cherokee Logo
Posted on Jun 24, 2008

Oxygen sensor wiring diagram

My 97 cherokee catalytic converter was stolen, oxygen sensor wires cut. the replacement is black, grey and white. the jeep is different color. i need help knowing which wires get connected to which.

  • 7 more comments 
  • Anonymous Oct 04, 2008

    95 mustang diagram for o2 sensor colors for grounds and sensor

  • bigocker Oct 07, 2008

    replacement lambda sensor [bosch LS 07]has 2 white 1 black 1 grey

    jeep has 4 different colored wires that arent in bosch instructions

    any suggestions

  • fpz50 Oct 11, 2008

    the plug is gone from the 02 sensor that goes to the engine. just the wires are there. same thing on the other end in the exhaust--just wires hanging there. there's no way to know what color I should splice to what as there are no matches on either end---help?

  • carlosrag Jan 31, 2009

    in my case the oxygen sensor of my jeep cherokee 2000 4.0l was ripped off male and female conectors included the wires are just hanging there the sensor i bougth have 4 wires: 2 white one black and one gray i need the match to the cars wires

  • rjcmol Mar 14, 2009

    Hello (jeeper zj, 1997 4.0)



    i have got an old oxygen sensor with the following colors



    wit/black/white/grey



    this is broken, i bough another one with the colors black/white/black/blue



    witch one can i connect ???

  • Anonymous Jun 06, 2013

    My 97 cherokee catalytic converter was stolen, oxygen sensor wires cut. the replacement is black, grey and white. the jeep is different color. i need help knowing which wires get connected to which.

  • Anonymous Mar 21, 2014

    my golf was stolen and recoved with a busted out ignition and must be hot wired but i do not know which color of wire s are what

  • Anonymous Mar 29, 2014

    The original oxygen sensor wires were burn by exaust, i boughy a new connector, but the one do i get from the dealer, have a different colors from the auto harnnes, i need to know how the wires has to be plug

  • Anonymous Mar 30, 2014

    Of all the wiring only 2 brown wires we don't know where to connect to. I urgently need a wiring diagram, Where can I get it?

×

2 Answers

Anonymous

Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

  • Contributor 1 Answer
  • Posted on Jun 06, 2013
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Joined: Jun 06, 2013
Answers
1
Questions
0
Helped
4961
Points
1

My 97 cherokee catalytic converter was stolen, oxygen sensor wires cut. the replacement is black, grey and white. the jeepoxygen sensor wiring diagram - icon1.png is different color. i need help knowing which wires get connected to which.

A

Anonymous

Ponteira trazeira do diferençial direita com rolamento 6 cilindros ano 97 cherokee laredo

  • Tom Mcbride
    Tom Mcbride Mar 15, 2014

    will the wires on oxygen senor have resistance in them

×

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer
0helpful
1answer

H.e.g.o sencer

A HEGO sensor is a voltage generator that is in the exhaust system installed between the manifold and the catalytic converter. It is used to sense the amount of oxygen present in the exhaust gases. Two wire type, black wire is earth, grey wire is sensor signal. If four wire type black is earth, grey sensor signal, two white wires are for a heater circuit.
0helpful
3answers

Oxygen Sensor 4 wire wiring diagram/instructions

Such are "universal" parts! But what can the vendor do, if their "universal" unit has to substitute for 2-wire, 3-wire, and 4-wire systems, without any modifications?
3helpful
2answers

2001 Cadillac Deville oxygen sensor wiring diagram

Why do you need a wiring diagram for a O2 Sensor? They are 4 wires and when you replace the sensor, you get a OEM. If you are going to get a Universal, it comes with a wiring diagram (GREY go to WHITE) and Black to Black
0helpful
1answer

1995 Jeep Grand Cherokee Laredo 4.0, 276+ K, new crank sensor, new cam sensor, new throttle sensor, new plugs , new cap & Rotor, new wires, has electrical cut in / out of engine run, drop of tachometer...

Hello Lubie...

I would STRONGLY recommend you get your codes read...

I TRIED ALL that TOO...

Finally my codes... said the OXYGEN SENSORS were complaining... OBD... DTC
(on-board-diagnostic... DIAGNOSTIC TROUBLE CODES)

So... of course I changed the... OXYGEN SENSORS.

The "NEW" OXYGEN SENSORS complained just as well...

I have subsequently learned the "SENSORS" are
just doing their job...

In my case reporting on a collapsed catalytic converter.
(muffler is actually a MORE common blockage).

A little hunting around... like Auto-Zone ... Napa auto...
Pep-boys... O'Reilly Auto Parts... even MIDAS might
yield FREE READINGs... (check around).

Just remember to wear your best SALES RESISTANCE...

and look up you prices on ROCKAUTO...
before you go... Hope this helps.

ROCKAUTO
1998 JEEP CHEROKEE 4 0L L6 Catalytic Converter RockAuto

1995 JEEP CHEROKEE 4 0L L6 Catalytic Converter RockAuto

Carnac the Magnificent
0helpful
1answer

I have a 1992 jeep yj 2.5L I bought. The oxygen sensor wires were cut right off when I bought it. I had to replace the oxygen sensor. the wires on the new sensor are black, grey, and two whites. The wires...

When you bought the replacement sensor it should have included instructions on what color wires match. If possible I would return to the store you bought it from and ask for the included directions.

The blacks go together and the greys go together, but I am not sure which other ones go together without knowing the brand and P/N of the replacement sensor.
0helpful
1answer

O2 sensor wire connections.my original o2 sensor adaptor got melted by my exaust,so it was cut off the original wiring harness which had 4 wires which are red/white, orange,grey/white and grey. But the...

Ford Explorer is equipped with two oxygen sensor positioned on the exhaust manifold. Its necessary to replace the oxygen sensor at the first sign of failure. You can get all necessary details about o2 sensor at http://www.wholesalesensors.com/ford-oxygen-sensor/
1helpful
1answer

Having trouble with wiring of oxygen sensor

there should be a paper inside the parts box that tells you how to rewire the after market sensor
Not finding what you are looking for?

4,971 views

Ask a Question

Usually answered in minutes!

Top Jeep Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

john h

Level 3 Expert

29494 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...