Peugeot automatic slows right down while driving then it decides to go againPeugeot automatic slows right down while driving then it decides to go again
AnonymousMar 12, 2014
2005 peugeot 407 exe slows right down while driving then takes of again2005 peugeot 407 exe slows right down while driving then takes of again
AnonymousMar 13, 2014
anti pollution peugeot 407anti pollution peugeot 407
AnonymousMar 14, 2014
peugeot 605 need service manual to adjust brakes systempeugeot 605 need service manual to adjust brakes system
how do I reconnect radio after disconnecting battery. I have the code.how do I reconnect radio after disconnecting battery. I have the code.
AnonymousMar 17, 2014
hi when i hit the brakes on my 2005 peugeot 407 i have a bad judder on my steering wheel and i have new pads&discs many thankshi when i hit the brakes on my 2005 peugeot 407 i have a bad judder on my steering wheel and i have new pads&discs many thanks
AnonymousMar 18, 2014
where is oil sump plug locatedwhere is oil sump plug located
AnonymousMar 20, 2014
reset rear camerareset rear camera
AnonymousMar 21, 2014
How do I remove the radio?How do I remove the radio?
AnonymousMar 23, 2014
heater on drivers side remaining coldheater on drivers side remaining cold
AnonymousMar 28, 2014
need wiring diagram for rear wiper motor fine had that checked told got a break in a wire butr dont have any diagrams in my haynes manuelneed wiring diagram for rear wiper motor fine had that checked told got a break in a wire butr dont have any diagrams in my haynes manuel
AnonymousMar 31, 2014
cost to replace clutchcost to replace clutch
You can't post conmments that contain an email address.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Hi Rod Normally rear disc brakes are self adjustable.
To fit pads you normally have to release hand brake adjuster completely. You then wind the piston fully in and fit pads. reconnect hand brake cable (if removed). Then pump brake pedal several times until it becomes firm (brakes now adjusted) you then readjust hand brake (normally 5 to 6 notches). Wheels should spin on 0- on 1-2 should just slightly turn 3 'possible' movement 5-6 locked. Note these numbers are only guides. Hope this is some help Good luck
You may need to adjust the cable for your hand brake. The driver's side is too tight and the passenger side is too loose. Best thing to do is drop the hand brake (e-brake) down, loosen the adjuster on the drum, then lift the hand brake until you hear 5 clicks. Then adjust the handbrake cable on both sides until the disk just stops.
Take the vehicle to Autozone, Oreilly's, NAPA, they will put a "CODE READER" on your vehicle for FREE to help diagnose the problem. They will also show you where the part is on the vehicle and loan tools but they cannot replace the part for you.
Sounds like a sensor either on the pad or on the mastercylinder.
I recommend you get a Haynes repair manual on your vehicle as there are several adjustments you may need to look at. If this is the first time you have had this problem and have less than 50,000 miles on the brake pads then it is most likely the cable and there are a couple of places to adjust in most cases. If you have 50,000 or more miles on those read pads you may need to replace the rear brake pads. The manual will help you in doing this repair correctly.
I has a clicking/knocking noise on one of my 407 (54 plate) front wheels after a change of brake pads. On investigation I found that the bracket to which the caliper hydraulic hose was fixed (at the lower end of the suspension strut) had been bent downward and was catching the CV boot clip. I bent it back up and the noise went. It is possible (if the brake caliper is not supported during pad change) to bend the bracket supporting the hydraulic hose. It could also interfere with the ABS wheel sensor bracket - check. Simply jack-up and support the car on the side with the noise and turn the wheel by hand to see what gives (don't go under the car until it is supported safely)..
need to change back brake pads n peugeot 407
Peugeot automatic slows right down while driving then it decides to go again
2005 peugeot 407 exe slows right down while driving then takes of again
anti pollution peugeot 407
peugeot 605 need service manual to adjust brakes system
Dipstick chaffing turbo pipe Peugeot 407
how do I reconnect radio after disconnecting battery. I have the code.
hi when i hit the brakes on my 2005 peugeot 407 i have a bad judder on my steering wheel and i have new pads&discs many thanks
where is oil sump plug located
reset rear camera
How do I remove the radio?
heater on drivers side remaining cold
need wiring diagram for rear wiper motor fine had that checked told got a break in a wire butr dont have any diagrams in my haynes manuel
cost to replace clutch
×