How do i remove the passenager side door panel to see why power window will not roll up

You have to remove the door panel to get to the window crank assembly. The window has fallen off the pin the roller is on or a carrier bolt has come loose and let the window drop. You can hurt anything by removing the window crank and door handle then the panel to access the window crank assembly to see what went wrong.

You need a flat head screwdriver to remove the light cover and the door lock and window switch. and a phillips head screwdriver to remove the two screws, the one under the door/window switch could also be a small bolt. (When removing the door/window switch cover pull back on the door handle or you will scratch the cover when removing it). Then pull straight up on the hand bar and you can slip door/window switch cover through the hole.

Sounds like your window is off track. You will have to take door panel off to get to it. Fairly simple to do once you remove the panel.

FRONT DOOR TRIM PANEL - REMOVAL
Release door latch and open door.
Roll window down.
Remove window crank Window Crank - Typical , if equipped.
Remove screws attaching trim panel to door Door Trim Panel and Trim Panel Screw
CAUTION: Do not forcibly pull trim panel from door, damage to trim panel may occur.

Simultaneously lift upward and outward to release retainer steps from inner door panel Trim Panel Retainer
Disengage inside handle linkage rod from inside handle.
Disconnect speaker harness wire connector Speaker And Power Mirror Connector
Disengage power mirror wire connector, if equipped (driver's side only) Speaker And Power Mirror Connector
Disengage clips attaching power window/lock switch panel to door trim panel. Disengage wire connector from switch panel, if equipped Power Door Lock/Window Connector
Separate door trim panel from vehicle.
INSTALLATION
Position trim panel at door.
Engage wire connector for window/lock switch panel, if equipped. Engage clips attaching power window/lock switch panel to door trim panel.
Engage power mirror wire connector, if equipped.
Connect speaker harness wire connector.
Engage inside handle linkage rod to inside handle.
Align trim panel retainer steps with inner door panel and slide trim panel into place.
Install screws attaching trim panel to door.
Install window crank, if equipped.

Hope helped with this; remember rated this help. Good luck.

Unless it has a handle (ie. it isn't a power window) you r going to have to tape up the window unless; you want to remove the door panel, and crank the tiny window gear by hand. (would not recommend).

Yes the door's rubber window guide becomes dry and needs to be lubricated with a special silicone lubricant, go to Napa and ask for this silicone lube then apply it to the grooves located around the inner perimiter of the door window frame, sometimes it is neccessary to remove the door panel to access the lower window guides, if you remove the door panel becareful when removing clips along the lower part of panel you can damage the panel using a screw driver the sell a tool for this it looks like a screwdriver with a Y shape at the end. If this doesn't remidy the problem you more than likely have a worn out window motor that needs replacement.

No won't be fuse. My guess is there is something faulty with the main controller. You could probably verify this by trying the switch on right rear passenger door. If it works there then the problem is at the main controller in the driver door. Could be a loose wire or the switch itself is broken.

there is only a sock filter. it is in the gas tank. you can get to it from the trunk. under the carpet.

1, Disconnect the able from negative terminal of the battery.
2. Pry the courtesy light from the door trim and disconnect the wire connector..
3. Remove all door trim panel retaining screws and door pull armrest assemblies.
4. Remove the door switch panel and the control switch panel and the control switch assembly.
5. On models with memory seats/mirrors, use small-flat bladed pry tool to remove and disconnect the wire.
6. Grasp the trim panel lift up and pull out to detach it from the door. Disconnect the inner door handle lock rod from the handle. Unplug any electrical connectors remaining and remove the door panel.
7. To install, connect the wire harness connectors and place the panel in position in the door. Press the trim panel down into place until the hooks are seated.
8. Install the armrest/door pulls, the courtesy light and the window switch'
9. Reconnect the battery


Also. You will need star pattern drivers to remove the window and motor from your door. If you have all the equipment it should only take you 1 hour.

so is the right rear door ??
if so here are some instructions.

1. If applicable, remove the regulator handle by pulling the clip out with a wire hook.
2. Remove the inside door handle and disconnect the latch rod.
3. Remove the screws and detach the clips attaching the door panel (see trim pad remover.
4. Disconnect the power window and courtesy light harnesses.
5. Remove the door panel bracket and carefully remove the plastic cover
6. Remove the screw attaching the door lock crank. Disconnect the latch rod from the latch side.

if you have an email address i can send some images on how to do it.
hope this helps