My ld20 diesel engine has one mark on the crank pulley and 3 on the cam pulley along with the numbers 1 2 3 . My unit has a timing chain not a belt what is the proper alignment of these marks?

All crankshaft pulleys have a timing mark. However, the actual marks can be different between manufacturers. Some have a notch cut on the rim of the pulley others have an arrow or a Dot stamped or moulded on the face of the pulley.
If your replacing a belt, line up the Cam marks and carefully examine the Crank pulley. You should be able to find the marks for the pulley and it's matching mark on the engine block. Some timing chains use marks on the pulley and marked links on the actual chain. I think yours might be a plain round dot or dimple on the raised face nearest the chain teeth.
*Note* The matching crank marks might not be at TDC on the actual pulley.
Some pulleys are stamped with extra marks to help set the advance and retard on the engine. Give the face of the pulley a good clean with a wire brush as sometimes dirt and surface rust can hide the mark.

the Renault koleos is a Korean made vehicle operation off a base Nissan diesel engine
research shows it as a chain and this is easily confirmed by inspecting the timing cover of the engine
if it is plastic it is a belt but if all aluminium it is a chain
if it is a belt , it will need the belt change at the 10,000 k mark which should include , crank seals , cam shaft seals , idler pulleys and hydraulic tensioner if fitted
the reason for all of the parts is simple
oil destroys belts very quickly and as the seals , idler pulley bearings and adjuster all are worn then they should be replaced as well to give another 100,000k service

When I did a timing chain on my Datsun I set up TDC on number 1 cylinder and then used a dob of paint on each pulley and a fixed point on the engine so that I could make sure everything lined up the same when I changed the chain.

The 2 cams are linked with a chain at the rear of the cylinder head.

The cams need to be set so the slots on the chain sprockets line up with the cam tower caps with 16 links between cam caps.

You cannot see the front crank pulley tdc mark so you need to lock the engine at tdc with a screwdriver jammed into the timing hole on the bell housing after setting engine at tdc or use a DTI
to check to tdc in the #1 spark plug hole.

If the cams have not been disturbed you only need to set the belt cam sprocket to the mark and crank to tdc.....all this means pulling the core support into the service position so the belt tensioner can be locked down and/or doing a complete belt job along with a coolant pump if over 70,000 miles..

By :"specs" I assume you need install position? To index the gears, whne you take it apart, turn the crank pulley 'till the timing mark aligns with the "0" on the timing scale. Don't turn the crankshaft again. When you are ready to install the chain, locate the mark on the crank gear and align the mark on the cam gear so they point to each other. The mark on the crank gear should be at 12 o'clock and the cam gear mark at 6 o'clock. Make sure when you put the cam gear on the cam that the location pin fits into the gear to position it correctly. Jeep recommends that after putting the chain and gears on, you rotate the engine by hand and place the crank mark at 6 o'clock and the cam gear at 3 o'clock, then count the number of pins in the chain (pins, not links) between those two points. There should be 15 pins. If you are rebuilding the engine and have the cylinder removed, it's a good time to check the front crank pulley (some have the outer ring move on the rubber). Put a piece of flat steel across #1 cylinder with a bolt through the steel extending into the bore center. Turn the engine by hand 'till the piston contacts the bolt. Make a mark on the pulley and turn the engine in the opposite direction till contact is again made. Your timing mark on the pulley should be exactly between the two marks you made. If not, make a new mark at that point and use that as your actual TDC reference. If it is radically off, replace the pulley.
When setting up cam position I always use a degree wheel. If you are installing an aftermarket cam
its important to do that. If you're just replacing a stock chain, You will be fine with the method I've outlined.

4 Cylinder diesel(4JX1) :
1 - Timing mark
2 - Cam pulley
3 - HP Oil pump pulley
4 - Tensioner pulley




6 Cylinder petrol:
Align crank(C) timing notch mark (1) to oil pump mark.
Align cam pulley(L+R) marks(3) to cylinder head marks
The cam belt has 3 marks, 2 lines and one mark that is actually a row of dots. Align the dots to the crank pulley groove mark(2) and align the other 2 lines to the cam pulley marks. Using a clothes peg to hold the belt to the cam pulleys works wonders to keep it in place while fitting. Please note the arrows on the belt and have them point in the direction of rotation - right to left side of engine
W - water pump pulley
I - Idler pulley
T - Tensioner pulley.

If for some reason you need to realign the cams on each bank :
Standing in front of the car and starting from YOUR left , looking at the cams you should see RE, RI, LI, LE on each of the camshafts.(R for right bank, L for left bank, I for intake and E for exhaust) Right bank camshafts are marked with one dot, left bank with 2 dots on the shaft itself. To align the camshafts to each other each cam shaft gear has a mark on it. Draw an imaginary line between the centre of the camshaft and the centre of the pulley. The alignment mark should be between the two along this imaginary line. The result will be that RI an RE will be at the top of each gear. The same with the left bank.

check around the inside (towards the block) edge or crank shaft pulley by the lower passenger side of the engine. Otherwise it will be by that pulley on the bloc, those are the only laces I've known them to be. Hope it helps

This unit will be running a timing chain. Now,The 1.6 "diesel" engine has both a belt and chain. In the diesel edition, the belt runs from the crank shaft to the cam and the other cam is ran by the chain.

go here for expert help on Villager & Quest

http://groups.yahoo.com/group/villagerquest/



Item Part Number Description 1 — 40 Timing Chain/Belt Teeth 2 6256 Camshaft Sprocket , Front 3 — 43 Timing Chain/Belt Teeth 4 6306 Crankshaft Sprocket 5 6268 Timing Chain/Belt 6 6256 Camshaft Sprocket , Rear
Removal

1. Drain the cooling system. Refer to Section 03-03 for the procedure.
   

1. Disconnect the battery ground cable (14301) .
   

1. Remove the generator drive belt, water pump and power steering pump drive belt, and the A/C compressor drive belt (if equipped). Refer to Section 03-05 for the removal procedure.
   

1. If equipped, remove the three A/C compressor drive belt idler pulley bolts and the A/C compressor drive belt idler pulley.
   

1. Remove the upper radiator hose bracket bolt.
   

1. Loosen the two upper radiator hose clamps and remove the radiator hose bracket bolt. Remove the upper radiator hose (8260) and the upper radiator hose bracket from the vehicle.
   

1. Remove the water bypass hose (8597) from between the thermostat housing and the water hose connection (8592) .
   

1. Remove the main wiring harness from the upper engine front cover (6019) .
   

1. Remove the eight upper engine front cover bolts and the upper engine front cover .
   

1. Raise and support the vehicle.
   

1. Remove the RH front wheel and tire assembly.
   

1. Remove the four RH outer engine and transmission splash shield bolts and two screws and remove the RH outer engine and transmission splash shield (6775) .
   

1. Use Strap Wrench 303-D055 (D85L-6000-A) or equivalent to hold the water pump pulley (8509) while removing the four water pump pulley bolts.
   

1. Remove the water pump pulley from the water pump (8501) .
   

1. Remove the crankshaft pulley (6312) . Refer to the procedure in this section.
   

1. Remove the five lower engine front cover bolts and the lower engine front cover .
   
2. Ensure that the timing marks between the crankshaft sprocket (6306) and the oil pump housing line up.
   
3. NOTE: The directional arrow is necessary to ensure that the timing chain/belt (6268) can be reinstalled in the same direction.
   
4. Loosen the timing chain/belt tensioner nut.
   
5. Remove the timing chain/belt .
   
   
6. Installation
   NOTE: Ensure that the timing marks on the camshaft sprockets (6256) and the seal plate are properly aligned. Ensure that the timing marks on the crankshaft sprocket and the oil pump housing are still aligned. NOTE: A new timing chain/belt has three white timing marks that indicate the correct timing positions of the camshafts (6250) and the crankshaft (6303) . These marks will help ensure that the engine (6007) is timed properly. When the engine is properly timed each white timing mark on the timing chain/belt will be aligned with the corresponding camshaft and crankshaft timing mark on the sprocket. Because the white timing marks are not evenly spaced you will need to refer to the following illustration for proper timing chain/belt placement. There should be 40 timing belt teeth between the timing marks of the front and rear camshaft sprockets and 43 teeth between the timing mark on the front camshaft sprocket and the timing mark on the crankshaft sprocket .
   
   NOTE: Verify that the camshaft timing marks are aligned with the timing marks on the seal plate, and that the crankshaft sprocket timing mark is aligned with the timing mark on the oil pump (6600) .
   
   Install the timing chain/belt starting at the crankshaft sprocket and moving around to the camshaft sprocket following a counterclockwise path. Do not allow any slack in the timing chain/belt between the timing sprockets. After all of the timing marks are matched up with the timing chain/belt installed, slip the timing chain/belt onto the timing chain/belt tensioner .
   
   
   
   
   
   

This is the best I could find for you .. I am unfortunately able to verify the info because I have no personal experience with this car or its engine ...