Front Door Panel removal removed the 5 screws on the door itself 2 on bottom 2 on inside handle and 1 behind interior door opener popped the plastic fastners around the door and removed the sideview plastic piece something around the lock and door handle in the middle seems to still be catching or screwed in and it wont lift up and off i cannot find another screw or how to remove anything else off the door panel to get to said screw if its there... im just trying to get to the speakers to replace them...

No you don't need any special tool . Find all screws on out side of door trim panel and the window handle , the mirror cover plate , then just pull on edge of the panel .
Gently pry the front side door trim panel (3) from the front side door by disengaging the plastic retainers which secure the panel.
Position the door trim panel (3) away from the door in order to gain access to the front side window switch electrical connector, if equipped.
Disconnect the window switch electrical connector, if equipped.
Remove the door trim panel (3) from the vehicle.
Remove the front side window switch from the door trim panel (3) by releasing the 4 plastic retaining tabs, as needed.

Use a cloth in order to pull off the snap ring which secures the front side door window regulator handle (1), if equipped.
Remove the window regulator handle (1), if equipped.
Remove the front side master window switch, if equipped. Refer to Power Accessory Switch Panel Replacement .

Remove the front side door inside handle (1). Refer to Front Side Door Inside Handle Replacement .
Remove the outside rearview mirror opening cover (2).
Remove the screw which secures the front side door pull handle (4).

Front Side Door Inside Handle Replacement
Removal Procedure
Remove the screw which secures the front side door inside handle (1).
Slide the inside handle (1) forward in order to release the retaining tabs which secure the handle to the door.
Open the front side door inside handle rod retainer and remove the front side door inside handle rod from the inside handle (1).
Remove the inside handle (1) from the vehicle.

Check out youtube video showing how to do it !
How To Remove Install Front Door Panel Suzuki XL 7

for passenger side:
1. unclip screw cover 'center flap' of inside door opener plastic cover, flap is 3/8"x 3/8" (center of plastic cover)
2. remove phillips screw now showing
3. push fabric panel (edge of door opener plastic cover-at hinged end of chrome handle) to allow uncliping of edge of plastic cover (top rt & lwr rt (for passenger side) of plastic cover)
4. open chrome inside door handle to allow plastic cover to be removed-slide plastic cover toward rear, free end of door to remove cover
5. remove switch panel-gently pry with wide non maring pry bar (cover wide blade screwdriver using cloth) do rear of sw panel 1st (don't pry front edge)
6. slide switch panel toward rear to allow removal
7. remove large phillips screw under sw panel
8. remove the 2 plastic covers near top, hinge edge -use plastic spoon handles to encourage caps to pop off. May also require small screwdriver approx 1/8" in to complete pop off
9. remove the 2 phillips screws w/ captive washers
10. remove 3 phillips/hex screws along the bottom inside of door panel
11. on outside/rear edge of panel push the 2 center pins of each in about 1/8"-this allows the clip to be pulled out w/ pin pushed in
12. remove plastic cover (REAR OF SIDE MIRROR)-pull window edge up and back.
13. lift rear of door panel (not hinge edge) up allow hinge edge to pivot around lower pin in door (hinge edge)
14. remove the 2 rt edge "L" brackets (gently pry center plastic pin out) (note the color and replace as removed)
15. slowly peel the clear plastc away from the non hinged end to expose the plastic panel with 3 phillips head screws
16. remove the 3 screws and panel for access to door handle.
17. using access area now available unlatch the rod attached to exterior door handle (unclip plastic to rotate clip up to allow rod to slide out-toward hinged edge)
18. using access area now available remove rod from ext door handle from inside door area
19. remove the 3 -10mm head bolts
20. remove the ext door handle (bottom edge out first)
reverse order to replace door handle

Remove one Phillips screw from leading edge of door panel (near latch). Remove small cap behind the door handle, inside another Phillips screw - remove screw and then the cup behind the handle. Look down in arm rest and there is another Phillips screw. Last screw is behind the approximately 1 1/2 inch plug on front upper corner of panel. At this point, gently pry around lower edge and sides - there are either five or six clips pressed into the door frame. Once all are disengaged, gently swing the bottom of the panel out and lift off the top edge of door next to window opening. Once panel is off door, gently remove the control plug from the door lock/window control on the rear of panel. Install in reverse order
hope this helps

1) Remove the plug inside the interior armrest and remove phillips screw.
2) Remove armrest and two screws that hold door panel to door frame.
3) Pop the outer cover off the interior door handle.
4) Remove the interior lock knob and remove door panel by popping out tabs connected to door frame and lifting up off of window ledge.
5) Remove the two nuts holding exterior handle in place.
6) Disconnect the L shaped linkage from the handle. The trick to getting the L shaped linkage into the new handle is to feed L shaped metal pole through hole in door where exterior handle was, leaving the lower end of this linkage in its slot.
7) Feed the end of L shaped pole through the plastic 'hinge' in new handle by folding the hinge over and pushing the end of the L through both sides of the plastic hinge at once. slide the lower loop of the plastic hinge down the L shaped pole to secure pole to handle.
8) Place new handle into door and reverse the process to reinstall interior panel.

Hope this helps Tim

It's easy!

1. Remove triangle-shaped plastic cover Fwd of door window - gently pry it off
   
   
2. Remove screw from the plastic cover behind door open lever
   
   
3. Remove door lock plunger. (unscrew)
   
   
4. Remove screws down inside the door pull hand-hold area
   
   
5. Look for other phillips screws - sometimes around the lower 1/2
   
   
6. Pry hidden plastic hold down fasteners from around the edge - pull the panel away from the door and where you see it 'stuck' to the door, slide a pry tool, a stiff putty knife works well, up in that area and pop the fastener off.
   
   
7. Lift door liner enough to get to the mirror power connector and unplug.
   
   
8. For some model years, with door panel loose, you can access the bolts / screws that hold the interior trim piece in place and remove.
   
   
9. Remove Mylar cover for access to 3 Mirror mount studs, speaker screws, door lock actuators, window motors, etc.
   
   
10. Remove nuts, (hold the mirror up from outside) and remove mirror. (Feed electrical harness through door openings as required to facilitate removal.
    
    
11. Reverse order for installation.

gently pry out the plastic insert behind the inside door handle and remove the two black screws behind. gently pry up the plastic insert covering the brass screw at the bottom of the handhold and remove. gently pry up the window switch panel from the rear, and disconnect the electrical connector by pressing down the catch, and pulling out of the socket. remove the two brass screws holding the center of the door panel that are now exposed. remove the black plastic cover in the upper most forward part of the door by gently prying. the rest of the door panel is held on using snap clips. gently pry away from the door, and work the door handle through the door handle opening in the panel as you slide the door panel up and away from the door itself.

Difficult to describe without pictures & illustrations.
1. The door handle is two-piece and the top piece is pryed off/out with a small screwdriver (needs to be removed in order to access two phillips screws behind it.. one at the top and another at the bottom).
2. The door release handle (inside cover) also has a small square cover that needs to be removed to access another phillips head screw behind it... then the cover pops out.
3. Below the arm-rest, there are two more cosmetic plugs covering two more (larger) phillips head screws which must be removed as well
4. The tweeter speaker (forward upper corner of the door is also 'popped' out to allow lifting the panel out of the door frame.
5. Now, there are approx four (4) more screws which need to be removed (covered by cosmetic bottons) three (3) aft and one (1) (possibly 2) forward.
6. Finally, the door panel is held in place by several pop-in round clips. Start prying at the bottom of door panel to start popping them loose & work your way upward to the top of the door panel... once all pop-in clips are popped out, you can now LIFT on the panel to remove it from the door frame. -- careful with the wire harness & connectors inside the door panel & cavity.

remove screws (several... front, bottom.. door handle pocket (covered by round plastic button), door handle (behind. remove tweeter speaker assy (upper front corner). Interior panel pops out to gain access to whatever is behind it. That's it. Anything else?

The door handle has a c clip behinde it that you can not see.Goto a auto parts store and thay will have a cheep tool to help you.(you need a special tool for this. The WINDOW CRANK handle has a 'c-clip' behind it. The door opening handle trim is held in by either a screw behind a plastic flap that will pop out(behind the lever)or it is held in at four points by plastic tabs (two on top and two on the bottom)that can be undone carefully with a screwdriver or the like. When this plastic trim is removed the door panel should come off.
Be aware that there are plastic clips (back side of the panel) on the perimeter of the panel that hold it in as well.
the tweeter panel just pops out look on the bottom of the door for screws and around the door handle and you will have to pop your window and door lock controls out and the reflector on the door pops out and there is two screws there then al you have is the clips behind the door they make tools for it but a flat tip screwdriver will be fine just get the tip close to the clip and pull it out .
1. Remove window crank (it has a kind of 'bent wire' c-clamp, which holds it onto the window crank shaft). 

2. Pry upwards the top plastic cover to the arm rest (this is a plastic coated foam rubber piece, on which you rest your arm). 

3. Remover the two now visible screws which fasten the arm rest onto the door. 

4. Remove the one screw fastening the inside door handle. 

5. With a blunt tool, gently hit the inside door handle in a forward direction (towards the door hinge). This will release the door handle from the door. 

6. Pry between the door panel and the door, to unsnap the snaps holding the door panel in place. 

7. Finally, lift door panel out and up to remove it from door. 

To Remove Door Panel on 2001 Honda Accord:

A: To remove the plastic piece with the door lock button and door handle connected to it:

1- Remove the screw in the middle located behind a plastic cover button
2- Push (slide) the whole assembly Forward (toward front of car)
Besides the screw, it is held in place by 3 hooks on the backside that hook into holes in the metal door frame
3- Now unhook handle from small metal bar going through door by pushing (toward door) plastic clip (blue?) off of the bar, then the bar will come out of the clip hole, thus releasing the handle.
4- Depress little grey button /bar (purple painted on it)on elec. connector to seperate connector, thus releasing door lock switch

Now the whole assembly (metal handle, door lock switch, and plastic piece) will come off door panel

B: The door is held on by 2-screws, 7-plastic snaps/plugs, and 1-plastic plug.

The screws are located: bottom of hand hold and the other behind the handle, both covered by little covers that have to be pryed off to access the screws.(hint: the screw with the built in spacer goes behind the handle when you are trying to reinstall)
The 7-plastic snaps: 3 across bottom and 2 on each side. Not visible, they are mounted to the inside of the panel.
The 1-plastic plug is visible at the upper front of the panel and is the same color as the surrounding trim


C: Take off the big plastic triangle piece above the door panel and behind the mirror. Pull/pry off. It has 2 snaps holding it on. one near bottom and one near the front.

D: Light lens prys off from bottom. Unscrew (1/4 turn) the light assembly with bulb still intact from backside of panel

E: Remove the Hand-Hold/window switch assembly: