Question about Dodge Intrepid

1 Answer

How to remove front axle on a 2002 dodge intrepid

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 179 Answers

Raise you vehicle on jackstands. remove front wheel and tire.remove front caliper from steering knuckle assembly, remove rotor from hub by pulling it staright off. remove speed sensor bracket from strut assembly. remove hub and bearing to stub axle retaining nut. dislodge inner CV stub shaft retaining ringon transaxle assembly. insert small pry bar between transaxle case and inner CV joint by prying on it.remove strut assembly to steering knuckle bolts remove top of steering knuckle from strut assembly, then rotate CV assembly out of vehicle. Remove inner shaft from transaxle stub shaft grasp inner CV joint and interconnecting shaft and pull both pieces out at the same time. good luck!

Posted on Oct 30, 2010

Ad

2 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 4 Answers

SOURCE: front cv axle 1995 dodge intrepid

Naturally you need to remove the tire then the brake caliper. After the brake caliper is removed then you need to remove the 34mm axle nut that is inside the hub. After that is removed then you can remove the hub. Becareful not to damage the hub seal on the back or you will have to buy a new hub (100 or more). Then you need to remove the strut knuckle assembly. Once the knuckle assembly is removed then you can pull the CV axle. Take care the inner CV housing is held in place by an inner snap ring. You will probably have to pry off the inner housing. Once the axle is off then install the new axle (if you buy complete axle). Make sure if you are doing both that you take care which side you are installing. I made that mistake and double the work. Slide the new axle on the spline and make sure it is seated completely. Then put back together the reverse of removal.

Posted on Mar 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dtc Code P2314


2002 Dodge Intrepid Ignition Coil Circuit Codes: Electrical ...

www.2carpros.com/.../dodge-intrepid-2002-dodge-intrepid-ignition-coil...
Aug 13, 2008 - 2002 Dodge Intrepid 6 cyl Front Wheel Drive Automatic 130000 miles. Getting the following codes. P0353 P2302 P2305 P2308 P2311 P2314

What are 2002 Dodge Intrepid trouble codes PO442 and ...

www.answers.com > ... > American Cars > Dodge > Dodge Intrepid
What does the Error Code P0846 on 2002 Dodge Intrepid mean? .... Trouble code P2314 means: Ignition coil E, secondary circuit - malfunction Trouble code .

Oct 29, 2015 | 2002 Dodge Intrepid

1 Answer

My 1996 dodge intrepid has a clunk when i turn parking the car and it shacks at 25 mph


this would be your cv axle the clunking is a sure sign ,its the same noise in all front wheel drive cars,if not fixed it can cause a number of other problems.this is your front drive axle.

Nov 24, 2011 | 1996 Dodge Intrepid

1 Answer

I have a dodge intreped 2002 2.7 v6 im trying to remove trans


Remove both drive axles first. Remove started.. remove transmission blots and torque convertor bolts. remove engine mounts. Support the engine with another jack to keep it level. 2 or 3 hours to do by yourselt...Good Luck!!!

Nov 03, 2010 | 2002 Dodge Intrepid

1 Answer

How do I remover and replace 2002 dodge intrepid left headlamp assembly. Thanks Roger C.


on the upper radiator support above the headlamp there shoudl be 2 bolts with very small heads, (about 5.5 mm). Take these bolts out, they should be very long pins. once they are removed, headlamps can be removed out teh front.

Oct 16, 2010 | 2002 Dodge Intrepid

1 Answer

How to replace the battery in a 2002 Dodge Intrepid


Hi there. The battery cell in this particular vehicle can be a little tricky to locate.You will first need to remove the right front tire. Next; Remove the right front inner fender liner. Once that is completed, you will expose the battery just to the inside of the right wheel fender liner. You can extract the battery at that point. Remember to remove the Neg- black post first, then, the Red+ positive post last.

Aug 13, 2010 | 2002 Dodge Intrepid

1 Answer

Axcle shaft 2003 dodge intrepid


remove tire/wheel and remove axle nut!! i thinks its a 32 mm socket and then take the upper strut bolts out of the knuckle theres 2 bolts 18mm if not there 15 mm bolt heads and tilt the knuckle outwards then drive the axle back with a hammer til it clears then take a flat tip bar and pry the axle out of the tranny

Jan 21, 2010 | 2003 Dodge Intrepid

1 Answer

Front cv axle 1995 dodge intrepid


Naturally you need to remove the tire then the brake caliper. After the brake caliper is removed then you need to remove the 34mm axle nut that is inside the hub. After that is removed then you can remove the hub. Becareful not to damage the hub seal on the back or you will have to buy a new hub (100 or more). Then you need to remove the strut knuckle assembly. Once the knuckle assembly is removed then you can pull the CV axle. Take care the inner CV housing is held in place by an inner snap ring. You will probably have to pry off the inner housing. Once the axle is off then install the new axle (if you buy complete axle). Make sure if you are doing both that you take care which side you are installing. I made that mistake and double the work. Slide the new axle on the spline and make sure it is seated completely. Then put back together the reverse of removal.

Mar 13, 2009 | 1995 Dodge Intrepid

2 Answers

How do you replace a water pump on a dodge intrepid 2003


The intake where the thermostat goes is in the driver side of the motor behind the altenator. I had to remove the front clip of the car and the altenator to get to it. It is quite a job.

Jul 20, 2008 | 2002 Dodge Intrepid

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,472 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...