How do i replace my tps - 1994 Buick Park Avenue

By tester, do you mean you have a P012x/P022x code from a code reader? If so, be sure to verify that the TPS itself is bad, and that you don't have a circuit (wiring) problem.
RockAuto lists the TPS as a separate part, so if it does turn out to be bad, you should be able to replace just the TPS. Some cars require that the TPS be calibrated with the ECM after installation; don't know about yours.

no engine option stated, and is key fact to know here.
eg:
The 5.7L V8 engine does not use a separate Throttle Position Sensor (TPS) on the throttle body.

remove old TPS, and bolt on new.
its like 2 or 3 screws. no big deal.
but needs to be calibrated per fsm.
ill take a wild guess, 3.7L
3.7L Engine and 4.7.

1. Remove air resonator tube at throttle body.
2. Disconnect TPS electrical connector.
3. Remove two TPS mounting screws.
4. Remove TPS.

install
The throttle shaft end of throttle body slides into a socket in TPS. The TPS must be installed so that it can be rotated a few degrees. (If sensor will not rotate, install sensor with throttle shaft on other side of socket tangs). The TPS will be under slight tension when rotated.

1. Install TPS and retaining screws.
2. Tighten screws to 60 inch lbs. (7 Nm) torque.
3. Connect TPS electrical connector to TPS.
4. Manually operate throttle (by hand) to check for any TPS binding before starting engine.
5. Install air cleaner tube to throttle body.

some TPS need calibration
to see what yours needs, read the FSM
or at alldata.com
or here. I think all engines here, are TPS PCM autocalibrated.

read WJ car here
http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

Hi OC, I'm glad to help!
OC, the best way I know to help you with this problem is to tell you to call the dearlership and if they offer the TPS without the Throttle Body, then yes you can replace the TPS only. NOTE: If they only sell the Throttle Body and don't offer the TPS by itself then you'll need the entire Throttle Body. If your asking if its OK just to replace the TPS the answer is YES, unless you have a problem with the Throttle Body itself like a vacuum leak or something like that. Hope this helps and have an awesome day OC.

Have you tried calling Honda parts to see if they sell just the tps? If they sell it then it is replaceable. Hope this help.

The TPS is used by the vehicles ECM for power enrichment,and idle stability when you remoce the sensor connector the ECM uses a substitute value so you can drive the vehicle. So the TPS is not the problem here You are basically suffering from a vehicle lean condition or false air. Removing the TPS connection only enrichen the car.Trouble shoot the MAF (mass air flow ) this is the one that houses the air filter check the boot going to the intake manifold make sure its not cracked or leaking air giving false air.

this code may cause by:

TPS not mounted securely.

TPS circuit short to ground or another wire.

Faulty TPS.

Damaged computer (PCM).

to fix this code you can try this:

Carefully check the throttle position sensor (TPS), wiring connector, and wiring for breaks, etc. Repair or replace as necessary
Check the voltage at the TPS (refer to a service manual for your vehicle for specific information). If the voltage is too low that is indicative of a problem. Replace if necessary.
If recently replaced the TPS may need to be adjusted. On some vehicles the installation instructions call for the TPS to be properly aligned or adjusted, consult a repair manual for specifics.
If there are no symptoms at all, the problem may be intermittent and clearing the code may resolve the issue temporarily. If this is the case then you should definitely check the wiring to be sure it's not rubbing on anything, grounding, etc. The code may come back.

this is an obd2 trouble code table, it can help you understand the meaning of code.
and for p0120
the Causes:
Sticking throttle return spring
MAP or TPS connector corrosion
Misrouted harness causing chafing
Bad TPS
Bad PCM
Possible Solutions:
If you have access to a scan tool, with KOEO (Key on engine off) observe the TPS voltage. With throttle closed, voltage should be about .45 volts. It should gradually sweep upwards to approximately 4.5 to 5 volts as you depress the throttle. Sometimes only a scope can capture an intermittent glitch in the TPS signal voltage. If you notice a glitch in the TPS sweep voltage, replace the TPS.
NOTE: Some TPS sensors require fine adjustment. If you aren't comfortable with using a DVOM (Digital Volt Ohm meter) to adjust the new TPS, then it's best to take the vehicle to a shop. If the voltage is not .45 volts (+or- .3 volts or so) with the throttle closed or if the reading is "stuck" then unplug the TPS connector. With KOEO check for 5 volts reference voltage present at the connector and a good ground. You can check the signal circuit for continuity by jumping a fused wire between the ground circuit of the TPS connector and the signal circuit. If the TPS reading on the scan tool now reads zero, then replace the TPS. However if that doesn't change the reading to zero, then check for an open or a short on the signal wire and if none is found, suspect a bad PCM. If manipulating the TPS wiring harness causes any change in idle, then suspect bad TPS.

most likely you have bad tps.. i would replace it..

A code P0123 may mean that one or more of the following has happened:

• TPS not mounted securely
• TPS circuit short to ground or another wire
• Faulty TPS
• Damaged computer (PCM)

Possible Solutions If there are no symptoms, the simplest thing to do is to reset the code and see if it comes back.
If there are symptoms such as the engine is stumbling or hesitating, carefully inspect all wiring and connectors that lead to the TPS. More than likely the problem is with the TPS wiring. Check the voltage at the TPS (refer to a service manual for your vehicle for this specific information). If the voltage spikes or is too high (over 4.65 volts with key on, engine off), then that is indicative of a problem. Carefully trace each wire from the TPS wiring harness to check for breaks, rubbing against other components, etc.
A code P0121 may mean that one or more of the following has happened:

• TPS has intermittent open or short internally
• Harness is rubbing and causing an open or short in the wiring
• Bad connection at the TPS
• Bad PCM (less likely)
• Water or corrosion in connector or sensor

Possible Solutions 1. If you have access to a scan tool, see what the idle and WOT (wide open throttle) readings are for the TPS. Check if they're close to the specifications mentioned above. If not, then replace the TPS and re-check.
2. Check for an intermittent open or short in the TPS signal. To do that, you can't use a scan tool. You'll need an oscilliscope. The reason is because scan tools take samplings of many different readings over just one or two data lines and can miss an intermittent drop out. Hook up your oscilliscope and watch the signal. It should sweep up and down smoothly with no drop outs or spikes.
3. If no problems were noticed, perform a wiggle test. Do this by wiggling the connector and harness while watching the pattern. Does it drop out? If so, replace TPS and re-check.
4. If you have no TPS signal, check for 5 Volt reference at the connector. If it's present, check the ground circuit for open or shorts.
5. Make sure the signal circuit isn't 12V. It should never have battery voltage. If it does, trace circuit for short to voltage and repair.
6. Look for any water in the connector and replace TPS as necessary.
P0152 Oxygen Sensor Circuit High Voltage (Bank 2 Sensor 1)

replace ignition coil make sure by dealer the right mode is used when ordering if not ordered right you will get a difference in engine volts