My 92 double cab mazda b 2600wont run unless you pore gas into inlet manifold. any one have an idea . the motor is injected

sounds like a failed gasket to the injection system , did you remove the inlet manifold, fuel rail/injectors or anything to do with the fuel

Are the pumps getting power, and is there a tank switch ?

change main jet in the carburettor install K&N air filter and iridium NGK or DENSO spark plugs tune up your engine change oil filter and oil. Flush your radiator check tyres pressure, Check engine compression and air leaks from inlet manifold ,Run hi octane fuel and injection cleaner mix for 250k to clean the carbon in the cylinders ,check for fuel hose loose ,carburettor leaks,distributor cup aluminium contacts to be clean, Vacuum hose on distributor unit for suction for advance timing .

did the crash fuel pump shut off get knocked from a large bump?push the button and retest if

Hi there,
I have a Mazda 6 which recently had black smoke / soot coming from the exhaust. On inspection, the inlet manifold was stuck open. I have just had the garage replace the control solenoid for the inlet manifold and so far the car is running ok.

Right-Hand
Removal

1. Remove spark plug heat shield (12A406).
   

1. Remove distributor to spark plug wires (12286) using Spark Plug Wire Remover T74P-6666-A.
   
1. Disconnect muffler inlet pipe.
   
1. If equipped with secondary air injection, disconnect the secondary air injection check valve tube (9B480).
   
1. Remove attaching bolts and right exhaust manifold (9430).
   
1. Inspect joint faces for signs fo exhaust leaks, cracks or any defect that would make exhaust manifold unfit for use
   

Left-Hand Removal






1. Remove oil level indicator tube (6754).

1. Remove spark plug heat shield.
   

1. Remove distributor to spark plug wires using Spark Plug Wire Remover T74P-6666-A.
   

1. Disconnect EGR valve to exhaust manifold tube (9D477). If equipped with air injection, disconnect the secondary air injection check valve tube.
   

1. Disconnect muffler inlet pipe.
   

1. Remove attaching bolts and exhaust manifold (9431).
   

1. Inspect joint faces for signs of exhaust leaks, cracks or any defect that would make the exhaust manifold unfit for use.
   

Installation

1. Clean mating surfaces of right exhaust manifold or left exhaust manifold and cylinder head (6049). Clean mounting flange of right exhaust manifold or left exhaust manifold and inlet pipe(s). Clean mounting surface for air injection tube or right exhaust manifold. Apply light film of Premium Long-Life Grease XG-1-C or -K or equivalent meeting Ford specification ESA-M1C75-B to right exhaust manifold or left exhaust manifold.
   

1. Position right exhaust manifold or left exhaust manifold on cylinder head. Install attaching bolts and washers, starting at fourth bolt hole from front of each right exhaust manifold or left exhaust manifold. Tighten bolts to 34-47 Nm (25-35 lb-ft), working from center right to both ends.
   
1. Position inlet pipes to right exhaust manifold or left exhaust manifold. Install attaching nuts and tighten to 34-47 Nm (25-35 lb-ft).
   
1. Position the secondary air injection check valve tube and the secondary air injection tube gasket (9C435) at rear of right-hand exhaust manifold. Install attaching bolts and tighten to 19-25 Nm (14-18 lb-ft).
   
1. Attach the secondary air injection manifold tube (9B449) to left-hand exhaust manifold fitting (located under EGR tube). Tighten nut to 30-40 Nm (22-30 lb-ft).
   
1. Attach the secondary air injection check valve tube to rear of right-hand cylinder head. Tighten bolts to 75-85 Nm (56-62 lb-ft).
   
1. Connect EGR valve to exhaust manifold tube to left exhaust manifold, if removed. Tighten nut to 53-72 Nm (39-53 lb-ft).
   
1. Install spark plug heat shield and distributor to spark plug wires.
   
1. Install oil level indicator tube to left exhaust manifold, if removed. Tighten nut to 13-24 Nm (10-18 lb-ft).
   
2. Start engine (6007) and check for exhaust leaks.
   

Hope this helps you...WF †

DEFINITELY it has an electric issue since it runs with a jump battery, have the alt checked again and the charge regulator also. Good luck

yes it will not allow the water to heat the inlet manifold but it will still work when its warmed up unless your in alaska

Did the bolt break off flush with the top of the hole? or if you remove the cover is some bolt sticking up? if there is try and use vice grips to get ahold if the bolts if it is flush then drill the bolt out and re-tap the hole. Way cheaper and likely less work too...

its the ecu ,my camry had the same problem. one of the injectors is staying open and flooding the cylinder.changerd the injectors same problem,changed the ecu problem solved.