What is the heat transfur tube ? does the engine have to be pulled to repair ?--2001 dodge intrepid

Check the ASD relay , auto shut down relay in the under hood fuse / relay box . The ASD relay supplies B+ voltage to the injectors an ignition coils plus other thing's ! This may be you device voltage code problem as well as the other codes

This vehicle has a double overhead cam engine. The water pump is driven off the timing chain. Unless you have had experience doing internal engine repairs, this is not a DIYer job. There is great risk of doing more damage than good if any step(s) of the repair procedure are not done correctly.

only one place for parts like this and its the dealer ,take the chassis number with you when ordering

Hi, I don't have a picture, but trace the big hose from the bottom of the radiator to the engine, and it will be under the housing where the hose connects.

2.7L Engine

1. Disconnect negative cable.
   CAUTION Do not remove pressure cap with the system hot and under pressure because serious burns from coolant can occur.
   
2. Drain cooling system.
3. Remove radiator lower hose from thermostat housing.
4. Remove nuts from heater tube flange studs.
5. Loosen starter bolt at heater tube bracket.
6. Pull heater tube out of thermostat housing and position out of the way.
7. Remove bolt and two studs.
8. Remove thermostat housing, O-ring and thermostat.
9. Remove thermostat housing bolts.

To install:

1. Clean gasket sealing surfaces.
   NOTE Install thermostat with the bleed valve located at the 12 o'clock position, between tabs on seal.
   
2. Install thermostat and seal into thermostat housing .
3. If removed, install two studs.
4. Install thermostat, thermostat housing and O-ring and bolt. Tighten attaching bolts to 105 inch lbs.(12 Nm).
5. Lubricate new heater return tube O-ring with coolant.
6. Position heater return tube flange over two studs. Install nuts.
7. Tighten retaining nuts to 53 inch lbs.(6 Nm).
8. Tighten starter bolt to 40 ft. lbs. (54.3 Nm).
9. Connect the lower radiator hose to the thermostat housing. Install hose clamps.
10. Refill cooling system.
11. Inspect for leaks.
12. Connect negative cable.

Hi!!

They are on top of the motor, 3 on each side, just follow the wires from the coils. To access, you need to remove the two torx screws fastening each of the spark plug wire boot, and pull it out, the boot is about six inches long. You'll also need a 5/8" spark plug socket with a long extension and ratchet.

Don't forget to rate this post. Good Luck!!

Check this firing order for all Intrepid engines...

2001 Dodge Intrepid 2.7 liter DOHC V-6 VIN "R"
or
2001 Dodge Intrepid 2.7 liter DOHC V-6 VIN "U"
or
2001 Dodge Intrepid 2.7 liter DOHC V-6 VIN "V"
or
2001 Dodge Intrepid 3.2 liter SOHC V-6 VIN "J"





Hope helps (remember rated this).

If this car has the 2.7l engine you should not buy it. Google: "2.7l sludge" They were a very big problem and the car in general has had a number of problems.

YOU NEED A REPAIR MANUAL BECAUSE YOU HAVE 3..2 L- 3.5L -2.7L ENGINE.YOU HAVE 3 DIFFERENT ENGINES.

this is an emission leak code..could have cracked emission hose at back of engine or on top of fuel tank..check gas cap for corrosion or filler tube for holes

look for 1 inch black boxes near the top of your engine pull up on them plugs should be there