Question about 2004 Chevrolet Colorado

1 Answer

I'm trying to remove my factory running lights/turns signals to install after market lights. How do I remove the old lights?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 22,485 Answers

Do not fit these lights unless they come with certificate of homoglonation as they could be illegal to fit

Posted on Oct 05, 2010

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace the drl moduler


this might not be much of an answer,, But why do you think your DRL is ,gone,,, Do you have HIDS? led tail lights or after market bulbs anywhere in you running lights system, such as turn signals front or rear marker lights corner lights etc, if you do have Hids or leds,, and you didn't put in resistors in line with the lower wattage led bulbs you car can throw the drl light, like turn it on., and with daytime running lights you will short out the hids, since they are not meant to run at say 4 volts like the factory non hid ones that are dim when the running lights are on.... I don't know if my answer will help you but I hope it does.. good luck

Dec 09, 2014 | 2002 Honda Civic

1 Answer

Tail lights dash lights and turn signals not working


obviously it may have to do with the installation of the new stereo, while installing some fuse may have blown or wires are cut or wires were not put back in order.

Feb 08, 2013 | Cars & Trucks

1 Answer

2006 monte carlo tail lights and turn signals not working


you could have blown some fuse while installing the stereo. check the fuses, wires that may have been cut or disconnected.

Feb 08, 2013 | Chevrolet Monte Carlo Cars & Trucks

1 Answer

What amp alternator is best for 96 maxima


depends on what accessories you have and want to run.. if you have after market stereo with lots of watts then you want to run the highest possible amprage you can get. if its just all factory accessories then just a factory alternator will be fine.. your old alternator will have a stamp of the amps it is and replace with the same.. i have installed custom built alternators with as much as 245 amps so it could run the stereo system with-out lights dimming

Jul 14, 2012 | 1996 Nissan Maxima

1 Answer

Install problem with h3 fog light bulb for 2002 wrangler


If it is a double filament bulb, try to rotate by 180 degrees in base, since there is a difference in power and touch of the bottom pins

Sep 10, 2017 | Jeep Wrangler Cars & Trucks

1 Answer

Where would I begin to troubleshoot lack of right turn signal at trailer plug?


Factory installed or after market.
Most of the SUV's, the trailer lead drops back to a splice in plug.
I would start there, and work my way forward
Do both turn signals work in the back of the truck?

Feb 12, 2010 | 2006 Ford Expedition

1 Answer

Parking lights on Nissan Frontier on - trailer parking not. 4 pin connector to factory connector (after market sealed wiring) - brake and turn signals work - no power to "brown" wire at factory connector...


First check the fuses. There may be one for trailer running lights. Check also power at the harness. If the brake lights and turn signals are seperate, there has to be a converter from 5 to 4 wire. For the power to feed back to the brake lights it sounds like the vehicle wiring is direct and not using a converter... or one of the bulbs on the trailer is contacting both contacts. Try http://www.etrailer.com/faq-wiring.aspx and maybe get a simple 4 pin tester that plugs into the 4 pin connecter. Hope this helps.

Oct 24, 2009 | 2005 Nissan Pathfinder

1 Answer

Alarm system stoped working on 87 caddy fleetwood


First question , is it a FACTORY alarm or an AFTER MARKET alarm. Regardless, I haven't met an alarm yet, that protects the radio.. My guess is, that if it is an aft/market alarm, inadvertantly placed the system in the "VALET" where it doesn'i work. Let me know if you disconnected battery, and are there alarm toggle switches.

Mar 23, 2009 | 1995 Cadillac DeVille

1 Answer

1998 4runner trailer light wiring not working


I recommend that you tighten the ground wire screw for starters. since the vehicle is ten years old corrosion may be the culprit.

Feb 01, 2009 | 1998 Toyota 4Runner

Not finding what you are looking for?
2004 Chevrolet Colorado Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...