How to change alternator belt - 1997 Nissan Maxima

Nissan xterra alternator removal and installation - YouTube

? 2:53
https://www.youtube.com/watch?v=n35OVegqBsg
Feb 7, 2014 - Uploaded by Francisco Delira
2001-2004 Nissan xterra alternator removal and installation removing ... how to replace the alternator on ...

How to Change an Alternator : Removing the Serpentine ...

? 4:02
https://www.youtube.com/watch?v=nJgVJNtZxuA
Oct 18, 2007 - Uploaded by expertvillage
Learn how to remove a serpentine belt with expert car maintenance tips in this fre... ... How to Change an ...

Alternators ' Starters ' Belt Tensioner ' Tensioner Pulley ...

https://www.pepboys.com/parts/alternators_starters/

Pep BoysFind alternators, alternator belts, parts and starters you need at Pep Boys. ... Regulators; Alternator Relays; Belt Tensioners Pulleys; Alternator Repair Kits ...

2001 Pathfinder alternator installation problems - Nissan Forum

www.nissanforums.com/pathfinder/172789-2001-pathfinder-alternator-i...

Dec 14, 2012 - 10 posts - ‎3 authors

Will most vehicles, the alternator is located near the top with a belt going directly to it. This makes removal easier as you only need open the hood (bonnet) for access. Disconnect the battery's negative terminal first, and then disconnect the alternator's electrical connector. Loosen the belt tensioning bolt (also serves to affix the alternator) and tap it with a hammer to get it free to move to remove the tension from the belt. Unscrew the bolt completely and the alternator will be off. If you don't have the new alternator with you, put the bolt back in the mounting hole and snug it up so you won' misplace it. Buy a new alternator belt and inspect the starter belt while you at it. It is easier to change both at the same time, but the starter requires you get under the car to loose it from belt tension.

The alternator belt can be changed from the top, the ps belt is best done from the bottom with the tire removed.
The alternator should have an adjusting bolt and the ps has an adjusting bracket. You loosen the bolts for the alternator and ps pump then use the adjusting bolts to tighten the new belts.

require to loosen of alternator mount bolts. Slide the alternator towards the rear of the car, this will slacken off the belt. Remove alternator belt and feed over the harmonic balancer and fan.Fit new belt. Slide alternator foward untill their is around 10-15 mm deflection in the belt, and tighten alternator mount bolts again to secure belt and tension. Recheck tension after about 500kms

undo the bolts that hold the alternator on its bracket there stoping you pulling the alternator off the belt
when you have the new belt on pull belt tight and nip up all the bolts again

just loosen alternator bracket adjusting bolt push down alternator slip drive belt over alternator drive pulley.when done installing new belt lift up on alternator to increase tension on belt.if alternator drive belt tension correct from longest span of belt take thumb press on drive belt should get 1/2 inch deflection once correct tighten alternator bracket adjusting bolt.

hi mate,your problem is fairly easy to fix-----remove the plastic under tray on the drivers side,from underneath, undo the main alternator bolt,just enough to move the alternator, now from the top undo the belt tension adjustment locking bolt,then back off the tension adjuster itself until the alternator belt is loose and can slip off the pulleys-----fitting your new belt is the reverse to this. all the best.

If the belt is 3 yrs old or older, change it. If it has oil or anti-freeze or grease on it, change it. If new, add more tension to the belt.

Google "changing alternator belt on 2000 Camry" and I think you will find what you need.

loosen the bolt that is holding the adjuster of the alternator. loosen the belt by pulling it and the alternator would slide in. remove and replace the belt.

do the reverse on installation.

remember to tighten all bolts of the adjuster and alternator after tightening the belt.

tnx 4 using fixya,

drcool