When turning on my turn signals, they stay lit and don't blink like they should. I am trying to locate the signal relay in my 95 caddy seville

https://www.google.com/search?q=Location/95+pathfinder/turn+signal+relay/diagram&tbm=isch&source=univ&sa=X&ved=2ahUKEwjl6cq3vMjgAhWJ1uAKHeOqBZgQsAR6BAgDEAE&biw=1088&bih=504 https://www.google.com/search?q=Location/95+pathfinder/turn+signal+relay/diagram&tbm=isch&source=univ&sa=X&ved=2ahUKEwjl6cq3vMjgAhWJ1uAKHeOqBZgQsAR6BAgDEAE&biw=1088&bih=504

Looks like it's the turn signal relay. It should be located on the drivers side under the dash to the left.
Can't see any other way the left light would be steady.
Hope this helps.

Change the bulb.

Turn signals use what is called a flasher to regulate the speed at which the lamps turn on and off. Usually mounted in the fuse box. I have attached the replacement model for a 1996 Roadie. Should take all of 15 seconds to replace.

Looks like a blinker relay stuck.

There are 2 separate flasher relays. 1 for the turn signals and one for the hazards. I believe you have a bad flasher relay for the turn signals. The location of that is in the front seating area on the drivers side, under the dash on the drivers side of the steering column, mounted on support bracket. I provided a picture of what it should kind of look like although the picture I gave you is an aftermarket one so the color and such may be a little different but will look the same. Don't get it mixed up with the hazard relay which is located in the front seating area on the drivers side under the dash above the kick pane lmounted on top of the convenience. I am almost 100 percent sure the flasher and hazard relay are the same so if you want to just swap them out in order to have turn signals that should work. You won't have hazards however. I hope this helps you and good luck.

It could be your flasher relay going out. Should be under the dash.

i have the same exact problem, it is the turn signal switch...it's around 95 bucks at advanced auto parts.

Go under the dash on the drivers side, and locate the two flasher stat units. These are small round aluminum 'cans'. They plug in, and have flat blades on the bottom. (You of course won't see these flat terminal blades until you unplug them)

One is for the turn signals. One is for the four way flashers. I can't tell you which one is which.

Past this point, check all the grounds for the turn signals. The wiring harness at the front will have one, or two leads, (Wires), coming out that bolt directly to metal. Either sheet metal for the car, or to the frame. These leads have flat, round terminal ends on them, with a hole in the middle of the terminal.

The lead's terminal end bolts can work loose causing a bad ground, and/or, there could be corrosion in-between the terminal end, and the area of metal it bolts to. If so, use sandpaper, and clean the terminal end, plus the area of metal it bolts to.

There are ground leads, (Or lead), that come out of the rear wiring harness also. Check these.

Still no?
Then your turn signal bulb sockets have corrosion in them. This causes a bad ground.

You may be able to use a rolled up piece of sandpaper, and clean the socket.
(Also touch up the lead, {LED. As in the metal lead}, contact point in the middle of the socket. This is for the Positive connection, but it doesn't hurt to clean it while you're there.

After this is the turn signal switch in the steering column.
(My money is on a bad flasher unit)

hello......this sounds like a flasher for sure! it is cheap and easy too replace.....FLASHER is located under driver's side dash.......round shape, with 2-3 wires connected at 90 degree angle to flasher, good luck