How many quarts of motor oil does it take - 2005 Chevrolet Silverado 2500HD 2WD

Depends on your engine.

1980 JEEP CJ-7 2.5L 4-cyl Engine Code [B]
CAPACITIES
Engine, GM without filter..........2.4 quarts[1]
Wix Filter ........ 51040
Cooling System, Initial Fill..........8.0 quarts
Automatic Transmission, A904, 30RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, A999, 32RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, Total Fill
3 speed A999, 32RH..........8.4 quarts
3 speed A904, 30RH..........7.0 quarts
Manual Transmission, 4-SPD, SR-4..........3.0 pints
Manual Transmission, 4-SPD, T176..........3.6 pints
Differential, Front..........2.5 pints[3]
Differential, Rear..........4.9 pints
Transfer Case,..........4.0 pints

1. Add extra oil when replacing filter. After refill check oil level.
2. With engine automatic transmission operating temperature, shift through all gears.
Check fluid level in NEUTRAL and add fluid as needed.
3. 1984-1992 Models with command-Track, add 5 oz of 75W-90 GL-5 to shift motor housing opening.

TORQUES
Oil Drain Plug.....25 ft-lbs
Manual Transmission T176
Fill Plug.....15 ft-lbs
Drain Plug.....15 ft-lbs
Manual Transmission SR4
Fill Plug.....20 ft-lbs

1980 JEEP CJ-7 4.2L 6-cyl Engine Code [C]
CAPACITIES
Engine, without filter..........5.0 quarts[1]
Wix Filter..... 51522
Cooling System, Initial Fill..........11.0 quarts
Automatic Transmission, A904, 30RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, A999, 32RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, Total Fill
3 speed A999, 32RH..........8.4 quarts
3 speed A904, 30RH..........7.0 quarts
Manual Transmission, 4-SPD, SR-4..........3.0 pints
Manual Transmission, 4-SPD, T176..........3.6 pints
Differential, Front..........2.5 pints[3]
Differential, Rear..........4.9 pints
Transfer Case,..........4.0 pints

1. Add extra oil when replacing filter. After refill check oil level.
2. With engine automatic transmission operating temperature, shift through all gears.
Check fluid level in NEUTRAL and add fluid as needed.
3. 1984-1992 Models with command-Track, add 5 oz of 75W-90 GL-5 to shift motor housing opening.

TORQUES
Oil Drain Plug.....30 ft-lbs
Manual Transmission T176
Fill Plug.....15 ft-lbs
Drain Plug.....15 ft-lbs
Manual Transmission SR4
Fill Plug.....20 ft-lbs

1980 JEEP CJ-7 5.0L 8-cyl Engine Code [H]
CAPACITIES
Engine, without filter..........4.0 quarts[1]
Wix Filter..... 51258
Cooling System, Initial Fill..........13.0 quarts
Automatic Transmission, A999, 32RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, A904, 30RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, Total Fill
3 speed A904, 30RH..........7.0 quarts
3 speed A999, 32RH..........8.4 quarts
Manual Transmission, 4-SPD, SR-4..........3.0 pints
Manual Transmission, 4-SPD, T176..........3.6 pints
Differential, Front..........2.5 pints[3]
Differential, Rear..........4.9 pints
Transfer Case,..........4.0 pints

1. Add extra oil when replacing filter. After refill check oil level.
2. With engine automatic transmission operating temperature, shift through all gears.
Check fluid level in NEUTRAL and add fluid as needed.
3. 1984-1992 Models with command-Track, add 5 oz of 75W-90 GL-5 to shift motor housing opening.

TORQUES
Manual Transmission T176
Fill Plug.....15 ft-lbs
Drain Plug.....15 ft-lbs
Manual Transmission SR4
Fill Plug.....20 ft-lbs

Oilman

if it is a gas engine it should use 5 quarts, unless it has a heavy duty oil cooling system, then it may need up to seven quarts. Fill the motor with the first five quarts, the check the oil level with the oil dipstick. If its still low add one half of a quart at a time while checking level each time you add a half quar untill it show full on the oil dipstick..

A typical automobile holds 4-5 quarts of oil.....Depends on the size of motor. If changing yourself, Drain out all oil, change filter, put oil plug back in. Put 3- 31/2 quarts back into car. put oil cap on and start car. Let run for 2-3 minutes then shut back off. Wait for a few. Pull out dipstick wipe, put back in then pull out a second time...Now you know how much you need to top off level.

pretty sure that takes 7. Start with 5 then start the motor for like 15 seconds and shut it off. Recheck oil level and add more if needed.

You will need 4 to 5 quarts of oil depending the size of oil filter you are using. Rule of thumb large oil filters will hold about 1 quart of oil and a small filter will hold half as much. hope this will help you.

1996 Isuzu Truck Trooper 3.2L MFI SOHC 6cyl
The Engine Oil Capacity 5 7/10 Quarts (including filter)

Engine Oil Type and Weight
Oil for use in temperatures ranging from -13 to 100 degrees
5
Application:
Oil for use in temperatures ranging from -13 to 100 degrees
Note :
Quarts without filter change

Oil for use in temperatures ranging from 32 to 100 degrees
5
Application:
Oil for use in temperatures ranging from 32 to 100 degrees
Note :
Quarts without filter change

VALHD30
Application:
Oil for use in temperatures ranging from 32 to 100 degrees
Note :
Valvoline Premium Conventional 30 Motor Oil


Hope this help (remember rated and comment this). Good luck.

5 Quarts and then start the motor. Run the motor until the oil pressure reads on the gage. Shut the motor off, let sit for a minute or two and check the oil. If it reads low add the appropriate amount of oil to the crankcase. Then write the number of quarts of oil required on a piece of tape and place the tape on the inside of the glovebox for future reference.

Engine Oil (includes filter change) SAE 5W-20 Premium Synthetic / 7.0 quarts ( 6.6 L )

Click here if you can review the Owners Manual

I really hope help you with this (remember rated this help) Good luck.

if you have a 1ZZ engine

4.2 quarts, 4.4 quarts with oil filter change

if you have the 2ZZ engine (XRS model) it is

4.4 quarts, 4.6 quarts with oil filter change

NOTE these are updated capacities that reflect changes identified in TSB: TSB-0134-08 issued July 15, 2008.
Your owners manual will reflect a lesser quantity that Toyota has since revised.

Your truck is going to take about 5.5 quarts.
Since your motor have some high miles on it, I would use non-synthetic 10w-30 oil that has the high mileage formula.
Synthetic will cause leaks on an old engine because the molecules are smaller and will go through gaskets easily.
High mileage formula will help recondition the gaskets.