How to change fornt drivers wheel bearing on grand vitara 2002 model 2.0 ltr 5 door and where can i get a repair manual for this model

Hi, The Suzuki Grand Vitara is a superb vehicle, several reasons can be applied to rear end noise.

Most are not expensive or difficult to repair. However a few can be expensive.
Lets look at the most common, wheel bearings, are the usual component to wear and require replacement, if it is a wheel bearing, its much better to have both wheel bearings replaced.

A wheel bearing will become noisy at certain speeds and give of a distinctive noise, best noticed on a flat road.
However a repair shop can easy diagnose a wheel bearing for you.
Other problems could be found within the differential back axle, this can again be easily diagnosed by the engineer looking for a wheel bearing fault.

I hope this proves to be helpful

Adam

Danielle, On the driver side you may have stuff in the way, which may have to be removed, to change bulb. Sometimes it is easier to remove headlight then change bulb and reassemble. Videos attached make it look fairly easy to change he bulb with out removal of headlight.
Check the attached links,instruction and guides, Good luck.
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Suzuki Grand Vitara Headlight Bulb Replacement
Headlight Change 1999 2005 Suzuki Grand Vitara 2003 Suzuki Grand Vitara 2...
Auto Repair Maintenance How to Replace Headlight Bulbs
How to replace Suzuki Grand Vitara Tail Light Bulb

SUZUKI GRAND VITARA SERVICE REPAIR MANUAL 1998 1999 2000 2001 2002 2003...

for easy and best solution visit the link

Check the wheel bearings.

Here is a website that a free manual can be down loaded for your vehicle


http://ezinearticles.com/?Find-the-Free-Auto-Repair-Manual-You-Need-Online&id=92717

Hi.
There is no way of changing 2 press into 1 press. For unlocking all doors - press the remote 2 times.

Programming
When
Remote control buttons operated repeatedly while vehicle out of range and system becomes inoperative. System malfunction.
How
Ensure ignition switched OFF and all doors closed. Proceed as follows: Within 10 seconds, open driver's door and switch ignition ON. Within 10 seconds of switching ignition ON, switch ignition OFF. Within 20 seconds of switching ignition OFF, press and release driver's door contact switch 3 times. Within 10 seconds of releasing driver's door contact switch, switch ignition ON then OFF. Within 20 seconds of switching ignition OFF, press and hold both remote control buttons in turn for at least 5 seconds. The driver's door should lock and unlock once. Within 5 seconds of driver's door locking/unlocking, press remote control lock button Fig. 1 [1] or unlock button [2]. Programming procedure complete. Confirm programming has been successful by locking and unlocking vehicle.
NOTE: A maximum of 2 remote controls can be programmed.

these are seal bearing and they need to be press out and press back in this need to be done with a hydralic press not with harmer i can help if yopu are in the nyc are call me 718-821-1640

Lift the back of your car.With a stable rest and with the two hind wheels hanging, run your car up to the speed where you experienced vibration. have someone take care of the throttle and shifting while you observe the transmission shaft. You may have an imbalanced shaft.

xl-7 programming instructions first you need to stuff your head up under the dash and locate your module drivers side upper corner under dash does it say programmable transmitter (the first models had no programable modules) if it says that then......
1 confirm all doors are shut and key is out of ignition
2 open drivers door insert key and turn to on within 10 sec
3 turn ignition switch to off in 10 sec
4 push and release drivers door switch 3 times in 20 sec
5 turn ign. switch to on in 10 sec
6 turn ign. switch to off in 10 sec
7 press and hold lock and unlock button on transmitter for 5 sec within 20 sec of step 6 alldoors will lock/unlockto confirm correct process
8 press lock unlock buttons on second remote within 5 sec after step 7 once again all doors will lock/unlock to confirm
9 to add another remote up to a max of four repeat steps 1 through 8 this was taken directly out of an owners manual supplement that comes with a new keyless entry kit (part number for a xl-7 or grand vitara can't remember which one it goes to but it works on either one is 84900-67810) which you would have to purchase if yours is not programable these instructions are the same for vitara, grand vitara, xl-7 and the esteem hope this helps