Serpentine belt routing guide for 2003 Mitsubushi Lancer

Below is the master help link provided to go through belt routing diagram:---Timing belt, drive belt, serpentine belt, accessory belt, fan belt, engine belt routing diagrams for all types of car models?
Click the link below: ----

http://carbeltrouting.blogspot.in/2012/02/timing-beltdrive-beltserpentine.html
----------This will help. Thanks.

You can look the belt routing diagram up in the DAYCO belt guide catalog at this LINK
Please allow time for large PDF file to download

Pop the hood of the car and locate the serpentine belt routing diagram. The diagram on the 2003 Chevrolet Impala is on top of the fan shroud. The diagram will be a picture of all of the accessory pulleys and how the serpentine belt is routed among the pulleys. This diagram will give you the exact direction for routing the new belt onto the pulleys. If you cannot find a serpentine belt routing diagram, take a notepad and pen and draw out the exact routing diagram of the old belt across the pulleys.

2 Locate the serpentine belt tensioner. It is located below the alternator on the left front side of the engine. The tensioner on the 3.4 liter, 3.5 liter and the 3.9 liter engines will require a 3/8 ratchet to release the belt tensioner. The 3.8 liter engine will require a ratchet and a 15 mm socket for the belt tensioner. Rotate the belt tensioner clockwise to loosen and remove the belt from the belt tensioner pulley.

3 Slide the old belt from the belt tensioner pulley. Remove the belt from the remaining pulleys and pull the belt from the engine compartment.

4 Route the new belt across the crankshaft pulley first. The crankshaft pulley is the big pulley on the bottom of the engine in the center. Then route the serpentine belt across the remaining pulleys as directed by the serpentine belt routing diagram. Leave the belt tensioner pulley for last.

5 Rotate the belt tensioner clockwise again to relieve the tension and slide the new belt across the top of the belt tensioner pulley. Release the belt tensioner and the belt will tighten up as the tensioner applies pressure to the belt. Make sure the new belt is properly seated in all the pulleys.

6 Crank the engine and inspect the belt again to make sure that it stays seated in the pulleys.

Read more: How to Replace a Serpentine Belt on a 2003 Chevrolet Impala ' eHow.co.uk http://www.ehow.co.uk/how_6120665_replace-belt-2003-chevrolet-impala.html#ixzz1Yi6QLAjb

The serpentine belt routing diagram on Mercedes C180 Kompressor 2003


CS = Crankshaft
G = Guide pulley
Gen = Alternator
SC = Supercharger (Kompressor)
T = Tensioner
AC = Air Conditioning
PAS = Power Assisted Steering

2003 Mitsubishi Lancer 2.0L MFI 4cyl



Fig. Accessory drive belt routing-1.8L, 2.0L (SOHC), and 2.4L (4G69) engines

Fig. Accessory drive belt routing-2.0L (DOHC) engine

Fig. Accessory V-belt routing-Mitsubishi 1.5L, 1.6L, 1.8L, 2.0L and 2.4L engines


Hope helps (remember to rate this ansswewr).

The serpentine belt routing diagram for 2003 VW Passat V5 2.3 liter


CS = Crankshaft
F = Fan pulley
Gen = Alternator
G = Guide pulley
T = Tensioner pulley
AC = Air Conditioning
PAS = Power Assisted Steering

First, you need to have the diagram for how the belt is routed when you replace it.

Serpentine routing diagram...


Here is a link to a video on how to replace the serpentine belt. I hope it helps!

http://www.wonderhowto.com/how-to-inspect-replace-cars-serpentine-belt-267229/

First, you need to have the diagram for how the belt is routed when you replace it.
Serpentine routing diagram...



Here is a link to a video on how to replace the serpentine belt. I hope it helps!

http://www.wonderhowto.com/how-to-inspect-replace-cars-serpentine-belt-267229

You didn't list your motor size so please pick the applicable diagram:


Accessory serpentine belt routing—4.8L, 5.3L & 6.0L engines


Accessory serpentine belt routing—5.7L engines with A/C


Accessory serpentine belt routing—5.7L engines without A/C


Accessory serpentine belt routing—6.5L Diesel engines


Accessory serpentine belt routing—7.4L engines


Accessory serpentine belt routing—8.1L engines

Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.