Show me how to replace power steering pressure hose on 1995 GMC Yukon

happened out of the blue now? or bought it like this?>
yukon , or yukon xl1500xl or xl2500 ? i guess left own here.
check fuses
and scan the car.
I am sure the scans will fail with DTC, so scan it see what fails.
check PS fluid levels and
for PS hoses leaking,
check loose belts to PS pump pulley
or have real shop look at it??? auto repair shop, even ASE rated shops, USA??
guess 3, hydro-electric- steering option in place, ?and or.
got rear wheel steering option?
find the, RPO code tell what it is there read RPO yet? (as built list)

read the service manual here on steering, a very complex system
check it out.

https://eautorepair.net/Marketing/Default.asp

Power Steering Fluid Reservoir Outlet Hose Replacement

Removal Procedure

1. Remove the fuel injector sight shield. Refer to Fuel Injector Sight Shield Replacement .
2. Remove as much power steering fluid from the remote power steering fluid reservoir as possible.
3. Place drain pans under the vehicle as needed.


Click to Enlarge

4. Disconnect the power steering fluid reservoir outlet hose (1) from the remote power steering fluid reservoir.


Click to Enlarge

5. Disconnect the power steering fluid reservoir outlet hose (1) from the power steering pump.
ImportantDisconnect any clips as needed before attempting removal.

6. Remove the power steering fluid reservoir outlet hose from the vehicle.

Installation Procedure

Hope this helps a little.

hello,
If your Yukon is not steering properly then you could have a power pump problem, first thing to check is the fluid level and see if the fluid looks dark and brownish. most of the fluids are red in color. but other things to check are the brakes on the front of the truck and the wheel bearings a long with the steering parts just to make sure everything is in order and safe to drive.

How to Remove a Power Steering Hose the Easy way, Tool ...

? 7:49
www.youtube.com/watch?v=OVBFrMcmV7Y
Dec 12, 2013 - Uploaded by Artistry Photography How to Remove a Power Steering Hose the Easy way, Tool Review ... The removal of this power steering pressure hose is a hard job but the ...

Replacing A Leaking Power Steering Hose - YouTube

? 2:38
www.youtube.com/watch?v=l1boEHtawcM
May 12, 2010 - Uploaded by Scotty Kilmer replace the whole hose assembly, they hold 1600 psi pressure, you can't .... i was told i need a new power steering pressure hose for my 2003 .

have a pressure test done on the pump and if faulty then replace it.

Hello walker_227,

Removal Procedure:

SPECIAL TOOLS: You will need a power steering pulley remover and installer tool, DO NOT USE A HAMMER.

1. Remove the power steering pulley.
2. Raise the vehicle.
3. Remove the oil pan skid plate from the vehicle, if equipped.
4. Place a drain pan under the vehicle.
5. Remove the power steering pressure hose from the power steering pump from underneath the vehicle.
6. Lower the vehicle.
7. Remove the return hose from the power steering gearbox and the power steering pump.
8. Remove the bolt retaining the rear bracket to the engine.(See picture below)
9. Remove the bolts from the front of the pump.(See picture below)
10. Remove the pump from the vehicle.
11. Remove the bracket from the rear of the pump

Installation Procedure:

1. Reverse above procedure
2.Fill and bleed the power steering system.

I'm not sure if that truck has rack and pinion steering, or a steering sector. In either case, it sounds like you have stuck valve and the hydraulic pressure is fighting you, instead of helping you. When ever you turn the steering wheel the valve is supposed to move and direct the hydraulic oil pressure to help you steer. The valve is built into the sector or the rack and pinion, you may have to replace the assembly. There are companies that recondition those items so you might want to shop around.

IF THE RESERVOIR IS LEAKING YOU SHOULD REPLACE THE UNIT. CHECK THE LINES FIRST AND SEE IF ONE OF THE HOSES COULD BE THE PROBLEM. THE LINE THAT IS BOLTED TO THE PUMP IS THE HIGH PRESSURE SIDE THE ONE WITH THE CLAMP IS LOW PRESSURE

should only be 2 hoses coming from and to your PS unit 1 is high pressure and the other is a return line. the Fluid all over the engine compartment is from the fan blowing the fluid,

my suggestion clean the area fill the PS unit up and have someone start the vehicle and watch where the fluid is coming from.

Before I spent any money, I would take a close look to see what the problem is. What is the fluid level in the reservoir? Is the high pressure hose leaking that is going to the pump? Have someone turn the wheels from side to side and look for any leaks. If the hose is leaking, then get one from a parts store and replace it. Even if the power steering pump needs replaced, it is not a very hard fix. You can save yourself some hard earned dough!! Hope this helped. Good luck.