Allow the engine to cool completely prior to working on the car. Place a drain pan underneath the radiator. Crawl underneath the van and locate the white petcock at the base of the radiator. Loosen it using your hands and allow the coolant to pour out into the pan and then open the radiator cap at the top of the radiator using your hands.
Remove the air intake tubing using the flathead screwdriver and set it to the side. Then mark the perimeter of the hood latch with a paint marker. Unbolt the latch from the upper radiator support using the 3/8-inch ratchet and socket. When it comes time to reassemble the engine, align the latch with the marks you made with the paint marker to ensure proper alignment with the hood.
Remove the overflow tank hose using a flathead screwdriver. Unbolt the overflow tank from the upper radiator crossmember. Then unplug the electrical fan on the backside of the radiator using your hands. Unbolt the radiator from the upper radiator crossmember using the 3/8-inch ratchet and socket, then lift the upper radiator crossmember out of the engine compartment.
Remove the automatic transmission cooler lines from the side of the radiator using a line wrench. Unscrew the hose clamps on the upper and lower radiator hoses using the flathead screwdriver, then pull the hoses off of the radiator and tilt them down toward the drain pan. Unbolt the air conditioning condenser from the front of the radiator using the 3/8-inch ratchet and socket, as well as the air conditioning filter/dryer. Then lift the radiator out of the engine bay, tilting it slightly toward the engine and making sure you don't bump it into anything.
SOURCE: Can't remove water pump from 2007 Dodge Grand -
you must undo the three pully bolts turn the pully so it slips behind the mounting flange , then you should be able to wiggle it out , if it still hangs on frame you a long pry bar and push between frame and crankshaft bolt just hard enough to move engine slightly, this will definitly work and repeat to install. PS use a little RTV silicon to hold seal on new pump.
SOURCE: Replacing the starter on 2001 Dodge Grand Caravan
with most front wheel drives you must remove the passenger tire and reach through to the starter bolt with an extension and if I remember write with a 15 mm socket you can reach through and take out the bolt
SOURCE: Remove inside panel pass.side door of 2001 Dodge gr.caravan sport
1, Disconnect the able from negative terminal of the battery.
2. Pry the courtesy light from the door trim and disconnect the wire connector..
3. Remove all door trim panel retaining screws and door pull armrest assemblies.
4. Remove the door switch panel and the control switch panel and the control switch assembly.
5. On models with memory seats/mirrors, use small-flat bladed pry tool to remove and disconnect the wire.
6. Grasp the trim panel lift up and pull out to detach it from the door. Disconnect the inner door handle lock rod from the handle. Unplug any electrical connectors remaining and remove the door panel.
7. To install, connect the wire harness connectors and place the panel in position in the door. Press the trim panel down into place until the hooks are seated.
8. Install the armrest/door pulls, the courtesy light and the window switch'
9. Reconnect the battery
Also. You will need star pattern drivers to remove the window and motor from your door. If you have all the equipment it should only take you 1 hour.
SOURCE: location of radiator fan relay 1999 dodge grand
the relay is on the drivers side just below the headlight. you have to jack the car up to see it. it's bolted to the body with 2 8mm bolts. that is you have to use 8mm socket. It's black and about two inches square. It's a little hard to see but it is there. hope this helps leave comment.
SOURCE: I am trying to remove my radiator and place it
Chrysler Caravan/Voyager/Town and Country 1996-1999
Radiator - REMOVAL & INSTALLATION
Fig. 1: Before removing the hood latch, mark it's location on the crossmember with a paint marker or other tool
CAUTION
Do not remove the radiator cap or drain with the cooling system
hot and under pressure or serious personal injury can occur from hot
pressurized coolant.
Fig. 4: ... and the upper radiator-to-crossmember bolts, then ...
Fig. 5: ... unbolt the crossmember ...
Fig. 6: ... and lift it from the front of the vehicle
To install:
Fig. 11: Unbolt the lower radiator mounting brackets
Fig. 12: Once all of the components are removed or set aside, the radiator can be removed from the vehicle
Hope help with this, remember comment and rated this.
1,416 views
Usually answered in minutes!
×