Question about 2002 Chrysler Concorde
Battery is behind the front left wheel. You have to remove the wheel to replace the battery. (you can access the battery w/out removing the wheel, but you can't actually get the battery out unless you take the wheel off.)
Once the wheel is off, remove the inner-fender well mud-guard and you will see the battery just forward of the wheel well. From there it's pretty straight forward.
Once this is removed, you should be able to see the battery hold-down bolts.
Remove these and remove the hold-down assembly.
If you are removing the battery, remove the 1st battery cable.
Depending upon what battery you have, you may be able to slide the battery back toward the wheel and disconnect the 2nd cable.
Jack the vehicle up, put on jack stands and remove the passenger side wheel.
On the front side of the wheel well there is an access panel that needs to be removed in order to access the battery. There are 6-8 1/4" screws to remove. Then manipulate the cover until you can remove it, bending it slightly.
If you were unable to disconnect the 2nd battery cable earlier, you can now move the battery further towards the rear of the car. Remove the 2nd cable clamp from under the hood.
Slide the battery all the way out. It is heavy!
Reverse the instructions for reassembly.
Posted on Aug 17, 2010
Directions not clear enough. Got dick stuck in fuse panel.
Posted on Nov 11, 2015
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
The official way is to jack up the passenger side, remove the wheel and there is an access panel there. Remove the panel and slide the batterry into the wheelwell. Easy !! (What a pain)
After I did that once, I tried it from the top of the car. The air cleaner box is held into the side of the r by two rubber "prongs", but secured at the side nearest the engine with a third "prong" to a metal base that is bolted to the chassis. You can undo the bolt with a long extension socket, or you can try and pry the "prong" off the base.
You will also need to unscrew the screw clip that holds the main filter box top to the resyt of the air intake system
Posted on Nov 04, 2008
You will need to disengage the Negative terminal (Black side) and then the Red (positive side). In addition, there might be a securing bracket with two bolts or wing nuts, loosen these and the rods can be pushed down and twist out of the bottom. Once this is done remove the battery and head to your local Auto parts store, they can help you select the correct one. re-assemble as you have taken apart. you will need to re program your stereo and reset your clock, (prior to removing terminals) make sure there are no special lock out codes for your stereo. Good luck!
Posted on Sep 12, 2009
try removing passenger front tire and accessing battery compartment through panel on the front side of the wheel well. what i did. not real easy, but easier than removing all the components for access from the top.
Posted on Jan 19, 2009
SOURCE: battery removal
The battery is located under the right front fender behind the tire. Remove the wheel, remove access panel from fender well. From engine compartment, remove 2 battery hold down bolts,10mm, slide battery rearward to remove battery cables.
Posted on Oct 18, 2008
2 torx screws i beleive they are t15 long screws pull them all the way out but the light will only come out about 6 in unless u unhook wires
Posted on Jun 05, 2009
Tips for a great answer:
Jul 14, 2011 | 2002 Chrysler Concorde
Jan 03, 2011 | 2002 Chrysler Concorde
Dec 11, 2010 | 2002 Chrysler Concorde
Apr 07, 2010 | 1999 Chrysler Concorde
Mar 02, 2010 | 2002 Chrysler Concorde
Jul 28, 2009 | 1998 Chrysler Concorde
Jun 05, 2009 | 2002 Chrysler Concorde
Oct 18, 2008 | 2003 Chrysler Concorde
4,429 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: