Question about 1982 Ford F 250

1 Answer

Steering column horn wiring diagram need. horn sounds when the steering wheel is turned. 1982 was as far back as the years went on the selection, I do need 1972.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,403 Answers

Have to pull strng wheel off you have a horn wire grounding out when you turn wheel only 2 wires biggest issue pulling steering wheel

Posted on Aug 15, 2010

  • sueartn Aug 17, 2010

    Did that, did not fix the problem. the small spring that depresses when you press the horn ring may need to be replaced and/or shorting out. Impossible to find the part needed.

×

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is causing horn from steering wheel not to work?


You will need a wiring diagram but test the power to the column multi plug to see if power is available. Then carefully ground that wire and see if the horn sounds. The horn contact is basically a brass ring and a sliding contact to allow the passage of current as the wheel is turned. Operating the horn is just grounding the supply via the ring. It works off the FOB by a separate relay triggered by the signal.

Aug 05, 2014 | 2007 Nissan Armada LE

3 Answers

Horn not operating


you must check the contact switch on the steer wheel.

Aug 08, 2008 | Ford Explorer Cars & Trucks

1 Answer

Saturn Keep blowing horn fuse


Could be a short in the steering wheel or column. Or a faulty horn relay.
You may need a wiring diagram to trace the circuits from the relay.
Usually the black wire is the ground and the green is voltage from the relay.

Dec 18, 2012 | Cars & Trucks

1 Answer

Buick lesabre 1993 horn wiring diagram


is your horn relay good, swap another relay and see if that works, if not you should check wiring at lower steering column, you could splice wire from relay to wiring harnees at lower steering column inside vehicle

Sep 03, 2012 | Cars & Trucks

1 Answer

How to fix horn


First go to horn, its in the right side (passenger side) very front behind bumper. Turn wheel to the right, remove inner fender well, locate horn. Check to see if you have 12V there when the horn is activated to ensure its not just a horn. If there is 12V and ground and horn doesn't sound, you'll need a new horn. If voltage is good then back track to the horn relay, it should be under the hood electrical center (some earlier models were under the dash below steering wheel. If you press on the horn in the steering wheel, you should hear it click to locate. If not check the black wire going up the steering column, when jumpered to ground and horn sounds then the problem is inside the steering wheel, horn ring or contacts on the pad are faulty.

Feb 01, 2011 | 1997 Chevrolet Cavalier

1 Answer

My turn signals and brake lights no longer are working I checked all the fuses and they are fine. I didnt know if there was some kind of relay located near the fuse box, that may be shot?


there is no relay for the brakes but there is separate flasher for the signals. Your problem is more likely a wiring or switch issue, as these systems use the same bulbs. Check the wiring at the back of the truck. If someone put a trailer connection in there, that might be the problem. If not, the stop light wires go up the steering column to the turn switch and then back down to the lights. I have pasted your wiring diagram below and also instructions for getting to the switch in the steering column. This requires a couple special tools that you may be able to rent or borrow. Sorry this is not good news...

jturcotte_33.gif

Turn switch access:

  • Disconnect the negative battery cable.
  • Remove the steering column trim.
  • Remove the horn pad from the steering wheel.
    • Remove the steering wheel and horn collar.
    • Use a suitable puller to remove the steering wheel.
    • With a suitable compressor, compress the preload spring to the lock plate. Compress the spring only enough to remove the snap ring.
    • Use a pick and a small flat blade screwdriver to remove the snap ring.
    • Remove the lock plate, horn contact carrier, and spring.
    • Remove the bolts at the upper steering column support and the upper mounting bracket from the column.
    • Disconnect the turn signal wiring connector.
    • Wrap tape around the wire and connector.
    • Remove the hazard warning knob from the column.
    • Remove the switch retaining screws and remove the switch.

    Nov 03, 2010 | 1993 Chevrolet S-10 Blazer

    1 Answer

    Horn blows constantly, doesn,t blow the fuse or anything else. can this problem be outside of the horn blowing assy. on the steering wheel? it,s a 2000 galant. problem occurs all the time if the switch is...


    • The horn relay might have welded contacts (stuck in the on position). Pulling the relay should stop the horn.
    • The wiring harness on the steering column might have a broken wire to the horn relay shorting to someplace that applies power to the relay. In this case, turning the steering wheel all the way to one side or the other may stop the horn, and it won't sound when you press the horn button.
    • The horn button in the steering wheel is stuck on or shorted.

    Oct 28, 2010 | 2000 Mitsubishi Galant

    3 Answers

    I have a 63 Ford T-Bird that I can't get the horn to work. I have checked the wires and the grounds and they look good. The horns work when I tested them also but when I put the steering column together...


    You missed something putting the column back together. IDK the design of the wheel, but if all the wires to the column are good, I'd look at the switch itself in the column. Probably not making contact.

    Sep 12, 2010 | Ford Thunderbird Cars & Trucks

    1 Answer

    Horn wiring diagram 65 el camino


    a 1965 camino,centre steering wheel horn push? remove the steering wheel and check the carbon brush that runs against the copper metal ring on the bottom of the steering wheel

    Dec 24, 2009 | 1982 Chevrolet El Camino

    1 Answer

    Steering column is becoming loose on 1997 Buick Lesabre. I would like detailed instructions on removing the air bag module and steering wheel enouhg to get to where it needs to be tightened.


    Yes there are four bolts halfway down col. this removal procedure may help.REMOVE OR DISCONNECT
    1. Disable SIR System.
    2. Two screws at back of steering wheel.
    3. Position inflator module to gain access to wire connectors. Note wire routing for assembly reference.
    4. Push in and rotate horn contact lead counterclockwise, and remove from the steering column horn tower.
    5. Horn contact lead.
    6. Retainer (CPA) from SIR wiring connector.
    7. SIR wiring connector from inflater module.
    8. On models so equipped, disconnect steering wheel control switch connector.
    9. Inflater module. WARNING: When carrying a live inflator module, make sure bag and trim cover are pointed away from body. Never carry the Inflator module by wires or connector on underside of module. In case of an accidental deployment, bag will then deploy with minimal chance of injury. When placing a live inflator module on a bench or other surface, always face the bag and trim cover away from surface. Never rest a steering column on the steering wheel with inflator module face down and column vertical. This is necessary so that a free space is provided to allow air bag to expand in the unlikely event of accidental deployment. Otherwise personal injury may result.
    INSTALL OR CONNECT
    1. Steering wheel control switch connector it equipped.
    2. Retainer (CPA) to SIR wiring connector.
    3. Route horn contact lead to steering column tower; push lead into horn tower and rotate clockwise to locked position.
    4. Horn ground lead.
    5. SIR connector and retainer (CPA).
    6. Inflator module to steering wheel. Install top surface of module first to ease assembly and fit. Do not pinch any wires.
    7. Two screws through back of steering wheel to inflator module.
      • Tighten screws to 3 Nm (27 inch lbs.).
    1. Enable SIR system

    May 27, 2009 | 1988 Buick LeSabre

    Not finding what you are looking for?
    Cars & Trucks Logo

    381 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    Marvin
    Marvin

    Level 3 Expert

    85223 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22485 Answers

    gerry bissi

    Level 3 Expert

    4388 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...