How do i change a headlight bulb on a 2002 chevy malibu

SOURCE: replace headlight bulb

Actually there are two little black tabs on top of each headlight housing and you simply have to pull them up to release the whole headlamp.

Then follow the rest of emissionwiz's solution.

SOURCE: how to replace low beam headlight bulb on 1999 chevy malibu

just have a philip screw driver, remove the screw, pull out the light and take the light to the nearst aurozone and they will give you the right light, and put it back the same way.

SOURCE: how to replace headlight bulbs 1999 chevy malibu

Thanks Pierre!

Merci beaucoup!

Everything worked as mentionned. Be carefull with the plastic in the winter. Make sure to use a flat screw driver and get it close to the slider and not on the edge. I cracked one of the tongues. Those L shaped slots are under the plastic cover with the two big plastic plugs that you also remove with the flat screw driver

Pierre Godin, Boissevain Manitoba.

SOURCE: How do I replace a headlight bulb for a 2004 chevy

Change headlights in 2004 Chevy Malibu Classic
Open the hood and pull up on the two black tabs on either side of the lamp assembly. Pull the lamp assembly forward gently and unclip the wiring harness. Twist the socket counter-clockwise and remove it. The bulb should be removed by wiggling it.
Install new bulb in its place and turn the socket back into place. Reconnect the wiring harness and return the lamp to its original position. Line up the holes in the lamp assembly to the round ends of the mounting pins, and press down on the two black tabs to hook the lamp assembly into place.

SOURCE: Change headlight on 2008 Chevy Malibu

Hi there,

Well first you can please follow the below steps -
1. Make sure the ignition key is in the off position and the headlight switch is off. Release the hood latch.
2. Open the hood and locate the top of the headlight assembly where you intend to change the headlight. If a plastic shroud is present, locate the center bolt and remove it with a ratchet and a socket. Lift the shroud out of the way to access the headlight assembly retaining brackets. Some later models may feature a snap-release shroud requiring no tools to remove.
3. Locate the brackets on the top rear of each side of the headlight assembly. Lift them all the way up to align the hole on the bottom of each bracket to the retaining tabs on the assembly.
4. Pull the assembly forward away from the Malibu, but be careful not to scratch the bumper. There are three guide pins that require unseating. The guide pins are what aim the headlights and it may take some wiggling to get the pins from their seats.
5. Support the assembly with one hand and then reach behind the unit with the other. The low beam bulb is on the outside, the high beam bulb is on the inside. You can also replace the parking light if desired. Locate the wire harness connection. Un-clip the wire harness from the back of the bulb socket. Remove the bulb by turning it counterclockwise 1/3 of a turn to align the release tabs of the ring and the assembly. Wiggle the bulb out of the assembly.
6. Place the latex gloves on your hands before opening the package of the replacement bulb. Oil in our skin can damage the glass bulbs of halogen headlights.
7. Carefully insert the new bulb into the ring and then align the tabs of the ring to the tabs of the headlight assembly. Push inward and then twist clockwise 1/3 of a turn to lock the bulb in place. Reattach the wire harness. Rest the headlight assembly inside its cavity and test the operation of the headlight before securing the headlight assembly in place. Be sure to turn the lights and ignition back off.
8. Align the three guide pins to their seats and push the assembly back into them gently until they snap into place. Replace the retaining brackets by pushing them downward to lock into place. Replace shroud, if applicable. Remove the tools and old bulb and close the hood. Post comments for further help or information......

Good Luck!!