Location of oil switch 2002 chrysler 2.7 engine

The oil pressure switch and sending unit is located directly above the oil filter and next to the starter motor on the lower side of the engine block.

Kelli, on 2.7 motor it is by oil filter above steering rack, in the eng. block, I think some may behind alternator and bracket also.
If these location do not seem to be right, do a online search with your info. and engine size.

Dodge Magnum oil pressure switch oil pressure light
Chrysler 300 2 7L oil pressure sensor location

Chrysler PT Cruiser crankcase pressure Questions ... - Fixya

www.fixya.com > ... > crankcase pressure > Cars & Trucks > Chrysler

Chrysler PT Cruiser cars & trucks crankcase pressure questions and answers. Ask your ... The oil pressure switch/sensor is located on the rear of the engine block above the right axle I believe. Unless you ... Question about 2004 PT Cruiser.

You have a oil pressure switch which is located by the oil filter,it is screwed into block,just removed electrical connector,get wrench and remove.

• When the oil pressure is either high or low it will either turn the oil light "on" in the dash or move the gauge to the extremes
• Undetected high or low oil pressure can result in internal engine damage and/or gasket leakage. Here's a picture of what it look's like.

http://www.autozone.com/external-engine/oil-pressure-switch/duralast-oil-pressure-switch/chevrolet/s10-p-u-2wd/2002/6-cylinders-w-4-3l-sfi/31135_652060_8450

It is located on rear of engine back by the distributor use to be. see attached pic

This answer covers 1999-2005 Cadillac Deville, Eldorado & Seville.
Example Engine:
2002 Cadillac Seville STS 4.6L SFI DOHC HO 8cyl.

This engine has (2) Crankshaft Position (CKP) Sensors: the Upper sensor is CKP sensor B, and the lower sensor is CKP sensor A (this is included for the OBD-II DTC codes - P0385 references Sensor B = upper CKP sensor, whereas P0335 references the lower CKP sensor (sensor A)).

Both crankshaft position sensors are located in the front of the engine just above the oil filter adapter. To access both CKP sensors, jack up vehicle on the passenger side, remove the oil filter, and the oil filter adapter, including the Engine Oil Pressure (EOP) switch. See illustration.

The ARROW points toward Front of Car.
1. Upper Crankshaft Position Sensor (B).
2. Lower Crankshaft Position Sensor (A)
3. Engine Oil Pressure (EOP) switch
4. Engine Oil Level switch
The Oil Filter is the can-type object below the oil filter adapter, which includes the EOP switch. Recommend: remove oil filter with an oil filter socket/strap wrench, since it's close to the oil pan.

location of oil pressure sensor on 02 hyundai accent gl with a 1.6 liter engine is driver side front of engine. lower near the bottom of the radiator.mind you that is for a 1.6 l

There are three engines that come with this car, there are two engines 2.0 and2.4 with the oil pressure switch located on the right front of the engine block, and then if it has the 2.5 engine then the oil pressure switch is located on the leftside of the engine block above the oil filter, good luck,.

The oil pressure switch relays the oil pressure in the engine to the instrument cluster. The switch will illuminate the OIL PRESSURE light if the oil pressure drops below 2psi (13 pa). The switch is usually located on the side of the engine, under the intake manifold on the 2.2L engine and on the side of the intake camshaft housing on the 2.3L/2.4L engine.




Fig. 1: The oil pressure switch is located on the engine block under the intake manifold and is accessible from underneath the vehicle-2.2L engine



Fig. 2: Oil pressure switch location-2.3L/2.4L engine


Other, the low oil level switch activates the OIL light in the instrument cluster when the oil level in the pan goes below a certain level. The switch is mounted on the oil pan.


Hope this helped (remember rated this post).

Could be a bad oil pressure switch, or a bad oil pump. Both will cause this issue. Hope it is the switch b/c the oil pump is a costly repair.