Gears slipping When I shift from 3rd to 4th, and 4th to 5th gear in my 96 toyota rav4 the engine revs and rpms go up for a moment and then drops to almost nothing and my speed goes down. I am not getting any power from shifting to a higher gear. I think my Manual transmission is going. What could teh problem be and how expensive is it to fix

2wd right?(1995 is GEN1, T100)
auto trans or manual trans no told and both are told.
we can't guess drivelines blind,so tell it.?
2.7L, 3.0L and 3.4L engine options new.
toss coin land on A/T box. (most common )
the TCM decides all this not you,
the Tcm/Pcm/or TCU are all transmission brains , the PCM does engine too, and tells the TCM speed, and engine loads (hills etc)
rpm based on all that and gear ratio, in the transmission, 1:1 or overdrive. too and the axle ratio and tire size (circumference)
are tires stock, or low rider tiny.???????
5 speed manual or 4speed automatic and 4 engine choices not one told and if an automatic the TCM is turned to all things stated above.
a hard fact that. the RPM drips in OD ,overdrive and TCC lockup
the service manual lists 5 transmissions
A340F, A340H, A440, A442F and A343F units
top 2 are A340e & A340f (USA answers me) 2wd/4wd

A340F (30-40LE) 4speeds + tcc

seen too on
2000-2004 Tundra (4x2)
A = Aisin-Warner Automatic.
340 generation 3. 3L v6 used.
E=electronic shifted (TCM brain
F= 4wd same as E shifted.
3 electrically controlled solenoids for shifting and torque converter(TC) lock up(TCU runs the SHOW)

There is s TV cable here too, that causes upshifts late or early.
super hard top find this, Asian boxes. but here goes.
?1st: 2.80
?2nd: 1.53
?3rd: 1.00 (end to end lockup , look ma' NO gears here !)
?4th: 0.75 (23-spline, 0.705 21-spline
4th gear cam be less on smallest engine.(less rpm drop)
now you learn vast version of transmissions exits.
I read the side of box and it tells me the model there fully, every time.


so are you not getting 4th gear OD or the TC lockup failing
scan the PCM see if there are P07xx errors"? tranny errors. ?

in 3rd gear the RPM is the axle ratio and tire diameter (pi X r squared is circum and distance moved is that)

I can tell you the math below see the online calc. at end here.
and some TC slip. (it slips not locked up)
4 gear is RPM ,= is 0.75 x 3rd gear RPM. and tc slip.
TCC lock up is is less RPM but that depend slip and hills.
that is why I call them slush pumps, TC SLIPS and turns HP in to wasted heat and is why TCC was mandated by the EPA, for more MPG, and less waste.
that is how the pump slips as they say.

why not just see if all gears work (count them with easy right foot on flat earth)
and TCC locks up, in 4th
and scan the PCm for errors.
1,2,3,4+TCC is really like 5th speed, if you noodle that.
4-1/2" gear,(5th) locked.
make sure TV cable not rusted and jammed up and for SURE not jammed in the Pulled out position, rusted, there. and is WOT
wot is wide open throttle and that make the tranny shift way late
or never goes past 3 gear... test it.(or worse 2nd)
I see folks put a new transmission $2500 for the want of $20 cable.
wow. that. The TV cable bad is an on car fix.
P0750 to P0770 are all tcc errors to the box. scan it if gears ever shift wrong. and speed sensors failing or clutch packs slipping in the box,will dtc code out too.

so in 3rd gear the axle 3.4L auto T100 4x4 should have 4.30 gears.
so 1:1 x 4.3 is still 4.3 so 3000 rpm the read prop shaft.spins

at 3000 rpm and axles spin 698 RPM( AND TAD LESS TC SLIPS.)
knowing tire circumstance or diameter. nets speed.
manual trans runs 4.10 axles. (and no slip at all)
if not running stock tires the SPEEDO lies to you.
taller large tires spin slower and VSS lies. to cluster.
called ticket getter
235/75R15 (stock'ish)
Diameter : 28.9"

here is 4.3 axles.
3rd gear, 60mph , axle above 28.9" stock tires
is 3000 RPM
so shift to 4th, be on flat ground and light right foot and not hills]
and TV cable not JAMMED (rusted and locked out)
https://purperformance.com/p-29669-rpm-calculator.html

so 4th OD is, what .75 x 3000 is 2250 RPM (my guess never seen)
TCC locked up ,is less RPM, a bit.

so learn to scan any TCM(PCM) when gears fails.
scan it. now.

bad news you'll need to have your tranny replace or overhauled

Have you had problems with clutch slipping up to this point? Like engine revving up and no change in speed while driving. Like going into 4th or 5th gear, letting clutch out, giving gas, and feels like no response? Engine just revs up? That's a slipping clutch.
If that's your problem, you need a new clutch.

best advice is dont go 40mph in 5th gear... if you are going up a hill at 40mph in 5th gear i have no doubt that it is jerking, your putting too much stress on the engine. shift up to 4th or 3rd you will be fine. 5th gear is an overdrive gear. 55+mph

This button only makes the gearbox change from 3rd to 4th or 4th to 3rd, will not down shift in any other gear, make sure it is in 4th gear, usually above 60km, than press o/d off it should go into 3rd gear, if it does not than see a automatic specialist, it is usually a sensor, if you go to Toyota they will charge you a fair bit.

the gearbox may just need a good service like a new filter and fresh oil,,, or it could be the gearbox velve block pistons sticking or worst still it may be the clutches slipping nothing can be done then unless you strip the gearbox and fit new parts but the longer you leave it slipping the biger the repair bill will be

converter came loose

most likely worn clutch plates in g/box. check oil level.

Ratio codes generally indicate a pressure loss & slipping which the computer reads as a gear ratio problem. Likely you need a rebuild.

i supose u are talking about a strait shift tranny if so the tranny ha shifter fork in it for the gears that is what is broke it is not 2500 dollars worth if someone told u that take it some where else check other prices